My iphone 4 can't find a network

I bought my iphone 4 in Ny and brought to Brazil. It was working fine till last Friday. It can't find a network anymore. It says on the upper left corner "no service" instead of showing the carrier name and its signal. I tried to contact my carrier but it seems to be everything fine, I even tried de microchip on my Ipad and it worked perfectly, so it should be a proclem with the phone.
I tried to reset the device, but nothing seems to work.
Anyone could help me on this, please!!!
(excuse my lousy english, please!)

1. Try doing a hard reset:
Press and hold both the Home button and the Sleep/wake button simultaneously for about 15 seconds and release when the Apple logo appears.
2. If that doesn't work, use this article for troubleshooting: http://support.apple.com/kb/ts1398
3. If that doesn't solve the issue, backup the device and restore it as new.
In that case, use: http://support.apple.com/kb/HT4137
NB: set up as a NEW device because a software issue will be in the backup. If the issue persists after restoring as new, you should offer the device for service.
If you get specific error messages/codes in iTunes when updating/restoring, check this: http://support.apple.com/kb/ts3694 for causes and solutions
If you restore your iPhone to factory settings without a backup and still can't detect/connect to any network, you should offer the device for service.
Good luck
JW

Similar Messages

  • After I connect with my iPhone (3GS 5.0.1) to any Ad-hoc wireless Network then walk away out of the reach of my wifi network, my iPhone can't find any wifi Network afterwards, only by turning off the iPhone completely and turning on again.

    After I connect my iPhone (3GS 5.0.1) to any Ad-hoc wireless Network then walk away out of the reach of my wifi network, my iPhone can't find any wifi Network afterwards, only by turning off the iPhone completely and turning on again.
    switching off wifi and on again or going into airplane mode did't help!
    This problem happens only with ad-hoc wifi networks not with normal ones.
    (Ad-Hoc network was created on XP Computer)

    Welcome to Apple Discussions
    Sorry, but the 169.x.x.x IP address is internally generated by the iPod (and iPhone) and indicates that a network has been detected but no IP address has been issued. Your friends iPhone was not connected to your ad hoc network either - it connected to the internet through the 3G network.
    You should read through the Vista help screens on ad hoc networking for some insight how this works. You should be able to get some ideas there.
    In the mean time, $40 or less will buy you a very capable wireless router with four Ethernet ports and will simplify your network tremendously. Having used Windows ICS for a long time, the addition of a router and a real network simplified things so much.

  • IPhone can't find my wifi network. Why?

    I have a Wi-Fi network at home, using WPA2 encryption. My other devices - computer, iPad, AppleTV - can all connect to the network. But my iPhone can't. It keeps saying it can't find the network. What can I do to fix this? (My network does not have MAC access control, or a hidden network name, or anything like that.)

    Never mind, I found the problem: I had to switch to the 2.4 Ghz band on my Airport router.
    I don't know why that helped, but it did. :confused:

  • IPhone 4s can't find cellular network.  iPad logged right on. Tried soft reset and two button reset, neither worked. In Detroit airport any ideas?

    Iphone 4s can't find cellular network in Detroit airport. iPad logged right on. Tried reset network and hard boot and airplane off on. No luck. Any ideas?

    So, I can see that nobody had any ideas.  In case anyone is interested, I did cave and get an Airport Extreme.  My iPhone 4s connected in about 3 seconds, as did my MacBook, my iMac and my old 3G phone.  The router is in the EXACT SAME SPOT as my Netgear router.  No reception problems, no dropping wifi.
    The Sony Blu-Ray connected on the second attempt, but the TiVos are another story.  Reset my N-adapters to factory default and then did setup, found the network just fine assured me that my wifi was configured to the new router, but the TiVos refuse to connect.  It's always something! lol  I'm sure somebody can tell me how to fix this. 

  • My iphone can not find the wifi networks

    my iphone can not find the wifi networks

    Is your router plugged in?  Do you have internet?
    Come on...
    I have the same issue.  Yesterday I could connect to my wifi just fine, but today I turned on my wifi and the wheel just spins and spins.  I restart my phone and I get the "greyed out" wifi switch. So I restart, and I'm back to square one.  The wheel just keeps spinning.
    I've updated the router firmware, I've power cycled everything multiple times, and still nothing.
    Can anyone give a real solution? Or do we just have to suffer until apple update this **** IOS6?

  • Wi-fi bridge between two routers TP-LINK WR841ND (WDS).  HP 1536 dnf MFP connect to one of this routers (copper).  My Ipad or Iphone can't find HP 1536 dnf MFP (using Eprint). Ipad and iphone connect   to router across WiFi.

    Hello.
    I have wi-fi bridge between two routers TP-LINK WR841ND.
    The name of this technology - WDS.
    HP Laser JET 1536 dnf MFP connect to one of this routers (copper).
    Second device (my NETBOOK) connect to second router (WiFi).
    I have good communication between NETBOOK and HP Laser JET 1536 dnf MFP via WiFI-bridge.
    In usual case NETBOOK can find (and can Ping) network printer and make a print some files.
    But my Ipad or Iphone can't find HP Laser JET 1536 dnf MFP (using Eprint). Ipad and iphone connect
    to router across WiFi.
    Please, help!

    Are you using the ePrint Mobile App, the ePrint Printer Control App, or just trying to send an email to the printer's ePrint email address?
    Does AirPrint work?
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

  • My Apple TV suddenly can't find my network and tells me it is not connected..help?

    My Apple TV suddenly can't find my network and tells me it is not connected..help?  I have reset my time capsule and have all the latest updates. My iPhone and ipad do not show airplay even though I have it turned on in Apple TV.

    Try the following steps, check whether things are working after each step where appropriate, before trying the next.
    Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
    Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
    Restart the Apple TV (Settings > General > Restart).
    Restart the Apple TV by removing ALL the cables for 30 seconds.
    Restart your router.
    Restart your mobile device.

  • My iphone can not find my router

    Hi!
    What am I doing wrong. My Iphone can not find my wireless router and I know, that I write the password correctly, when it's asking for it.
    It comes back with the message: Can not establish connection to router.
    Please help me.
    Regards
    Lonni

    This is happening to me too (sorry I am not an answer)
    Mine worked fine and then I begun to notice that the wifi had dropped. I initially could reconnect in wifi settings but now it says 'not connected' and is stuck in a loop of looking for a wifi but not ever finding one.
    I have tired rebooting and reset network settings, I even bought a new up to date router.  The router powers another iphone in the house asn various outher apple gadgets like ipads so I doubt the router is at fault.
    I am begining to suspect a hardware problem, I hope not as it is out of warranty
    Any ideas?

  • Photosmart b209a can't find wireless network.

    I've only had this printer for three days. The "Easy One Button" process to get it to find a network failed. It cannot find my wireless network.
    I'm using XP Professional on my laptop. McAfee Virus scanning and Firewall. (Not that it matters if the printer can't find the wireless network)
    I have a DSL D-link router with NO MAC filtering and yet when I print the Wireless Network Test Report it gives me this whole spiel on MAC address filtering and asks to add the MAC address of the printer to the router... but there's no offered solution if MAC filtering is turned off.
    I've changed my router security key from WEP to WPA-PSK.
    I've managed to get it to connect twice... and to print a test page on separate days. I have no idea what it is I do that gets it 'online' but it doesn't seem to last.
    I have spent several hours over the past three days (wasting entire days) trying to work out what the problem is. I have read forum posts; I have googled for solutions. The troubleshooting guide for the printer seems hopeless.
    The printer is on the same desk as the router with only a computer monitor between them.
    When I print the HP Network Configuration Page it states the status of the 802.11 Wireless is "Disconnected". The printer's wireless light is on, showing that the wireless radio is working on the printer.
    I bought HP because my last printer was HP and it was excellent (but not wireless). If I can't get it to go online, seriously, I'll take it back and exchange it for a different brand of printer. All I want is a printer I can print to wirelessly, is that so hard to ask? Yes, I'm getting really frustrated here. I live in a rural area and I don't have access to geek friends or a computer professional or anything like that and returning the printer requires a two hour drive so I have to be as self-sufficient as possible. Please, try not to use too many technical terms. I can understand some but not all and if anybody can help me, please be clear in their instructions (ie, don't just say 'go to setup blah blah blah' without saying which setup you're talking about.)
    Thanks for any help. It is appreciated.

    Yes, the desktop is connected to the router with an Ethernet cable.
    Yes the laptop is wireless.
    The printer is connected to the router via wireless (which I've already stated, it keeps losing the wireless network).
    If I don't have my printer connected to the desktop via cable, then I won't have any printing capability at all, because, as I just said, the printer keeps losing the wireless network! I need at least some way of printing when the printer can't find the network (even though the wireless network is working perfectly fine).
    So, desktop connected to router with cable.
    Laptop is wireless
    Printer is wireless for laptop use (but it keeps losing the network and therefore is totally useless in that respect)
    Printer is connected to desktop via cable to enable printing because of wireless continuing to lose connection to wireless network.
    In fact my printer hasn't been able to connect to the wireless network for 2 days now... even though I'm currently connected to it on my wireless laptop.
    Sometimes the printer finds the network, sometimes it doesn't and when it does, if I try to print from the laptop wirelessly, the printer loses the network.
    This really is poor product and the installation manual might as well be used for toilet paper for all its worth, same with the 'help' feature on the disk. I only chose HP because I was familiar with it, since my previous printer was HP and reliable (but not wireless). I'm seriously wishing I'd purchased a different brand.
    I'm not an IT tech, but I've managed to be able to connect modems and routers and other peripherals to my network without too much hassle at all... until now.
    I'm sorry if I sound angry but this is completely frustrating. I spent good money for a product that I am unable to use for the main purpose I bought it! I'm reduced to saving things to USB sticks and physically taking them to the desktop computer and having to print from there.

  • My iphone can use only one network

    Hi, my iphone can use only Orange network. I live in mauritius and i just bought my iphone from Mauritius telecome Orange. Now when i insert another network on it, it says please insert simcard. I cant use other network on this. Is it possible to unlock it, and how?
    Some people told me to jailbreak it :O i dont wana do this!
    Please help me out.. i really love using iphone

    If Orange won't unlock your iPhone, and I'm sorry to say that according to Apple's information they do not offer unlocking (though call them to confirm) your only recourse would be to sell the iPhone and purchase a new one in the country to which you move, should you do so.
    Regards.

  • Where can i find my network key?

    where can I find my "network key"?

    One method is via the AirPort Utility, as follows:
    AirPort Utility > Select the AirPort > Manual Setup
    From the Utility's menubar: Base Station > Equivalent Network Password

  • HT5569 4S phone to IOS 7.1.2 and lost my wi-fi.   The wi-fi is on, but can't find ANY networks.   I have been through all the steps, from turning the phone on and off, resetting the network settings, resetting the whole phone, redownloading 7.1.2 an

    I updated my 4S phone to IOS 7.1.2 and lost my wi-fi.   The wi-fi is on, but can't find ANY networks.   I have been through all the steps, from turning the phone on and off, resetting the network settings, resetting the whole phone, redownloading 7.1.2 and lastly going to the Apple store for help.   They tried all the exact same steps I did, took the phone apart and looked at and said it is in "pristine" condition.   They have no idea why it isn't working, but they could offer to sell me another phone.    This is extremely annoying!    They claim it has nothing to do with the update to 7.1.2, but that is when I lost the wi-fi, so it has to be related!

    My 4s i-phone which is 2 years old cannot find any wi-fi networks not even my home network... I had the same problem two months ago but i turned off the i-phone for 8 hours and then it was okay... Now it happened again.... I tried to restart the modem but whilst my laptop is connected regularly, my phone still cannot find any wi-fi networks... I restart the i-phone, i reset it, i chose reset network settings, reset all settings, i turned it off for a whole day in case it was overloaded, i turned on the airplane mode and turned it off again, i put it into the freezer for 10 minutes within a zipped bag but 3 days now and i still cannot be connected to my home wifi... I went to the technician today and he told me that it means that wi-fi is broken and that i need to change it with a charge of 70 euro but i have to give my phone for 10 working days so as to be fixed... I am so frustrated and i don't know if i want to give 70 euro for wifi since i don't know if it would make the same problems again... 

  • Can't find my network utility ?

    can't find my network utility ?

    Care to share which OS you are using?
    Your profile is a complete blank.  Since you posted in the MBP forums, everyone is assuming that is what you have.

  • TS1398 My Ipad 2 can not find ANY networks. All my other devices in my home are just fine. Any thoughts????

    My Ipad 2 can not find ANY networks. All my other devices in my home are just fine. Any thoughts????

    My Ipad 2 can not find ANY networks. All my other devices in my home are just fine. Any thoughts????

  • Iphone 5 cant finde Cellolar network

    iphone 5 cant finde Cellolar network and cant connect to wirlles network
    all of that after restor and befor actuli
    i try to activet it but i cant whit out network place help me

    but is recognize wifi

Maybe you are looking for

  • How to get data from a table in a condition between twomonth

    hai friends I have a query that is i want to get data from a table based on a condition between two months in a format of char column Ex I have a column called from_month in the format of 'mon/yyyy'(already converted from date') then the second colum

  • Windows 2008 R2 SP1 failure Error 800F0818

    We are trying to update ServicePack 1 on a Windows 2008 R2. The update is being executed with WSUS. We tried to download the package from internet and the problem is the same. Error 800F0818. Here is the log of System Update Readiness Tool ==========

  • Error in using bapi

    Hi, I am using bapi 'BAPI_QUOTATION_CREATEFROMDATA' for creating quotation. it is giving error 'External number assignment is not defined for document type ZSQ' Can you please suggest me the reason of this error. Thanks, Sushant.

  • Dynamic WebService client within a WebService Handler

    We have a WebService running on WebLogic 10.3 that has a handler that contains a Webservice client that connects to a set of IIS WebServices. The client is called with code like this: QName qname = new QName("http://www.company.com/Webservices/", "Us

  • Java fx text editor

    Hi guys, I'm new of Java Fx technology, that I find fantastic! What I want know is to embed in my java fx application a rich text editor (like a smart word processor). What I need is this: 1) open a document format in text editor 2) perform formattin