My iphone 4 died even though it had plenty of battery, and shows no sign of life until i put it on to charge where it shows the apple sign every now and then but just turns off again after a few seconds.....HELP!!!!

my iphone 4 died even though it had plenty of battery, and shows no sign of life until i put it on to charge where it shows the apple sign every now and then but just turns off again after a few seconds.....HELP!!!!

Could be a defective battery, you should get it checked by visiting an Authorized Apple Service Provider or Apple Store next to your place.
Find an Apple Authorized Service Provider

Similar Messages

  • My iPad was working perfectly fine and then it just turned off and wont turn back on. it had around 60% battery what do i do?

    i need some help. my iPad was working perfectly fine about 20mins ago and then it just turned off and wont turn back on. its was at about 60% when it stoped working so i have ruled out the fact that its dead. ive tryed turning it back on but it wont please help.

    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up
    EDIT - sorry TeeKnows. I was too slow on the draw. My apologies.
    Message was edited by: Demo

  • When my phone is not plugged into the charger or computer, it will not turn on at all; even though it is not dead. When it's plugged into the computer, it will go to a white screen with a grey apple icon and then it will turn off again and repeat. IOS7

    When my phone is not plugged into the charger or computer, it will not turn on at all; even though it is not dead. When it's plugged into the computer, it will go to a white screen with a grey apple icon and then it will turn off again and repeat. IOS7 and iPhone 5.

    http://support.apple.com/kb/HT1808
    Try this step and if you cannot get your device into recovery mode there is a chance you have a hardware failure and you need to call apple to see what service options you have.

  • Firefox installation made my power saver function misfire - the system goes down after a few minutes of inactivity but then comes right back on again after a few seconds.

    My power management scheme: turn off monitor after 2 min of inactivity; turn off hard discs after 5 min of inactivity. doesn't work reliably anymore. Usually, with Firefox installed, the system powers down after the preset times but then comes right back on again after a few seconds. If I restart the machine, my selected power management scheme works properly for a few cycles but then reverts to the mode of turning back on after a few seconds after having shut down.

    Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).<br />
    See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]<br />
    <br />
    If it does work in Safe-mode then disable all your extensions and then try to find which is causing it by enabling one at a time until the problem reappears.<br />
    You can use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.<br />
    You have to close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")
    Your above posted system details show outdated plugin(s) with known security and stability risks.
    *Java Plug-in 1.6.0_05 for Netscape Navigator (DLL Helper)
    Update the [[Java]] plugin to the latest version.
    *http://java.sun.com/javase/downloads/index.jsp (Java Platform: Download JRE)

  • MG 3250 new printer turns off automatically after a few seconds.

    My printer was just bought yesterday, a new one. It could turn on at the beginning, but while I started to setup the wireless connection, I got a problem installing the driver on my laptop so I turned off the printer. After this the printer never turned on properly. Everytime I press the power button, the printer turns on for a few seconds, the scaner lights up and toner moves a bit, then it shuts itself down. 
    I totally have no idea what happened and have no clue whether it is the board issue or setting issue. The toner was stuck but I have fixed it, not helping with the turn off issue tho.

    So I did call Apple. That was pointless since they had no idea what was wrong. I made an appointment with a Genius at the Apple store nearest to me. The associate who checked me in said his wife had the same problem (and discovered it while on an 8 hour flight, which stinks).
    The genius who helped me was great. He had no idea what the issue was and hadn't heard of the issue before, so he took my phone into the back room and ran some diagnostics.
    He found that there was nothing wrong with the hardware at all, but he noticed an error with my firmware.
    He restored my phone (while my phone was plugged into itunes he held down the home and wake/sleep buttons. Then when the apple logo appeared he let go of the sleep/wake button but kept the home button pressed). This erased everything. I wasn't worried about that since all my contacts, apps, and music were backed up on my computer.
    I guess he reinstalled the latest firmware and os update. He put a couple of albums worth of music on there too for me to test it. Problem solved.
    It took an hour or two for me to get everything back onto my phone and in its proper place.
    That was a pain, but worth it since I can now listen to music freely with no interruption.
    The only thing I'm really ****** about is that my game data is all erased. Apparently when you back up your apps in itunes, it doesn't back up your progress/saves/scores in your games. I have about 30 games on my phone so this really, really *****. I guess I will just have to replay all the levels in Angry Birds, Peggle, Cut the Rope, etc. Lost a lot of progress in Infinity Blade which is pretty especially awful.
    I just listened to about a half hour of music with no interruptions though, so I guess its a fair trade.
    Good luck.

  • X31 backlight turns off annoyingly after a few seconds

    Weird problem with my x31.  Normally, everything is...well...normal.
    But every once in a while, the LCD backlight will turn off after 3-10 seconds of keyboard/mouse inactivity.  As long as I keep typing, the light will stay on.  But if I pause to think, the backlight goes off and the only way to bring it back on is to hit F3 to "darken the screen" and then move the mouse around or hit a key.
    It's like there's some sort of extreme power saving mode going on in the system.
    It happens even at the boot screen or the BIOS editor...so this is some bit of hardware that has gotten confused.  After a couple of hours, it goes away...but the system isn't much use when it's happening.
    When the backlight is off, the LCD is still painting a picture -- I just need to shoot a powerful flashlight at the screen and all the pixels are being properly controlled.  There's just no illumination.
    Ideas?  Is there some sort of software diagnostic that would knock some sense back into the backlight controller?

    No, the backlight is the color it should be.
    I turned off the power-saving mode for "auto-dim" -- but that is calibrated in minutes, and this is happening in seconds (not only that, but its erratic...sometimes 1 second, sometimes 10).
    Just for fun I downloaded the latest version of the Power Management stuff (which was just updated a week ago) and ran a whole series of PCDoctor diagnostics on the hardware.  Problem is gone for now...we'll see if that actually was the solution.

  • IPhone 5 died even though it was at 60 % battery

    This is what happened: I charged the phone before I left, and it was at 60 %. I hung out with some friends for a few hours, without using my phone. Then as I was walking home, I started listening to some music, and took a couple of photos with the iPhone camera. Two minutes later and the phone just died on me. I have no idea what happened. The music just stopped, it went black, and the charging symbol started showing. I tried to click on the start button, the restart button etc, but nothing was working. When I got home, I connected it to my Macbook Pro for charging, and it worked. It said the battery was at 60 %, and basically confirmed that the iPhone wasn't dead after all.
    What is going on? Can someone please help me with this.. do I need a new battery?

    Could be a defective battery, you should get it checked by visiting an Authorized Apple Service Provider or Apple Store next to your place.
    Find an Apple Authorized Service Provider

  • TS1367 My computer wont turn on it brings up a bar it fills 1/4 of the way then it just turns off

    please help I have a macbook pro I turn it on and it has sound and everything but a bar comes up it fills 1/4 of the way and then my computer turns off again please help me.
    my os x is:
    Mac OS X Lion 10.7.5

    Try starting you computer by holding down the command + R keys then run disk utility on your have drive to verify/repair it.  http://support.apple.com/kb/HT1782?viewlocale=en_US&locale=en_US

  • My macbook pro shuts down and doesnt let me turn it on after a few days i try to turn it on and it works but then after a few hours or so of using it it turns off again and the cycle of me waiting days to turn it back on happens again whats the prob?

    my macbook pro shuts down and doesnt let me turn it on after a few days i try to turn it on and it works but then after a few hours or so of using it it turns off again and the cycle of me waiting days to turn it back on happens again whats the prob?

    If you haven't already done so, try this simple step first.

  • My screen wont turn on, and the screen is black. It was working fine, but then it just turned off. The only way it will work is if I close my laptop, and pinch the two screens together

    My screen wont turn on, and the screen is black. It was working fine, but then it just turned off. The only way it will work is if I close my laptop, and pinch the two screens together

    You have a hardware problem and you should take it into a apple store to be looked at and fixed.

  • My iphone 4s was working fine then it just turned off and wont turn back on but my home button dosent work what do i do?

    my iphone 4s was working fine then it just turned off and wont turn back on but my home button dosent work what do i do?

    Apart from the battery being dead (make sure by plugging into a power source for 15 minutes), hold the sleep/wake button and home button together for 10 - 20 seconds or until the apple logo appears.
    If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support

  • When I try starting my iPod touch, it won't start; the Apple logo comes up for a few seconds, and then, it just shuts off. I tried to charge it through an outlet; the iPod didn't even charge, so I tried to restore my settings on my computer. iTunes won't

    when i try starting my IPod  it won't start, the Apple logo comes up for a few seconds,and then. it just shut off . I tried to charged it through an outlet, the IPod didn't eve charger so I tried to restore my setting in my computer, i tunes won't

    But that requires the computer to see the ipod. I am having the same problem and I keep being told to restore it, but you have to either get the ipod to turn on or have the computer see it in order to so that. Right now I have a pretty useless 32GB ipod touch cos I cant get the thing to turn on! I can only get the apple logo for like maybe 20 seconds and it goes away. Ive charged it for days on a wall charger, on the computer usb charger, and on a speaker charger. Nothing works.

  • My iMac turns on the start up chime sounds, you see the apple icon on the screen and then it just shuts off.  Any ideas?

    My iMac turns on the start up chime sounds, you see the apple icon on the screen and then it just shuts off.  Any ideas?

    Do these two resets:
    SMC RESET
    http://support.apple.com/kb/HT3964
    Shut down the computer.
    Unplug the computer's power cord and ALL peripherals.
    Wait 15 seconds.
    Attach the computers power cable.
    Wait another 5 seconds and press the power button to turn on the computer.
    The 5 second timing is important to a successful reset.
    PRAM RESET
    Zap the PRAM
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • My Wi-Fi works, but after a while not anymore. Then I've to turn of on the Wi-Fi and turn it on after a few seconds. Can anybody help me with this annoying problem?

    Hello,
    My Wi-Fi doesn't work good. After a while it doesn't work and then I've to turn of the Wi-Fi and turn it on after a few seconds. Does anybody has this same annoying problem?
    Jelle van Blokland.

    Hi Jelle van Blokland,
    Here is an article that has troubleshooting for Wi-Fi connections in iOS, including disconnecting:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Cheers!
    - Ari

  • I want to know what happened to my ipod cause for exemple, when I turn on sometimes all the screen appears with lines and everything look like lines and I have to turn off again..

    I want to know what happened to my ipod, cause after a while that it was off when I want to run in on it gets lines, like if that would be broken and I have to turn off again..

    What generation is your iPod? My sister's 2g/3g(I'm not sure which) was doing something similar, but it would put a different graphic on the screen every time. We took it in to the apple store and they didn't determine what it was. One thing they said to try was to restore it and gradually add content on to see if it's an app or something loaded on it. If that doesn't work then they said it's probably something in the software or firmware. They gave her the option of getting one exactly like the one she had or getting the new one like I have. She ended up getting the new one on sale at target.

Maybe you are looking for

  • Broken image in case of transport via NWDI

    I have a image file in a webdynpro application. I have placed it in the src -> mimes -> comps -> package folder. When I deploy the application I can see the image on the application. Now when I released the application from development to staging, th

  • Error occurred during initialization of VM & java/lang/NoClassDefFoundError

    ascertain:tcglive:~/BUILD/bin> ./listJobs Error occurred during initialization of VM java/lang/NoClassDefFoundError: java/lang/Object ascertain:tcglive:~/BUILD/bin> ./startJobServer -fg Error occurred during initialization of VM java/lang/NoClassDefF

  • Can't get iPhone 4s calander to sync to iMac

    The reminders and notes picked up on Mac.  Had two other people set everything on phone, however calander events on phone are still not showing up on calander on Mac.  Do see the events when going to ICloud online.  What's wrong?

  • Copernicus crashes when after adding certain fields to a Webservice

    Hi Everybody, I am having a frustrating issue that is causing Copernicus to crash whenever I add certain fields to a Web service. For instance, if I create a web service for the ServiceRequest BO, and include the TextCollection field, once it is save

  • FIELDS TO BE GREY IN A PO AT ITEM LEVEL

    Sir, i want to make some fields grey in a PO How can i configure it at document level. Example:Material tab,delivery tab wnted to be grey at item level regards amey Moderator message: subject in capital letters is not allowed Edited by: Jürgen L. on