My iphone 4s has hung up while trying to reset to factory defaults.

I tried to reset my iphone 4 s to factory default and it just hangs.ive tried turning off but it just has the line like its trying to update.

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
  3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
  4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
  5. If necessary, open iTunes. You should see the following "recovery mode" alert:
  6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Similar Messages

  • I am getting an error message that my network connection has timed out. while trying to update my iPhone on iTunes. Has anyone found a solution? I was given some advice about turning off my firewall and/or virus protection but am nervous about doing that.

    I get a message that my network connection has timed out while trying to update my iPhone on iTunes. Has anyone else had that problem and if so what solutions have you found? I was told to turn off my firewall and/or virus protection while updating but am nervous about doing that for obvious reasons. I'm also disgusted with Apple not providing free tech support.

    See this article about the ports that have to be open during the update process. iTunes has to contact Apple during the download. iTunes for Windows: Troubleshooting security software issues

  • I bought a iphone 5s from gumtree. While trying to activate it i realised there was an account linked to it through an apple id. it doesnt say the phone is in lost mode and it still has warranty. am i able to get a fix from apple?

    i bought a iphone 5s from gumtree. While trying to activate it i realised there was an account linked to it through an apple id. it doesnt say the phone is in lost mode and it still has warranty. am i able to get a fix from apple?

    unfortunately - no
    if the device is on ios 7.1 or above there's two things.
    1) the device may be restored to factory settings - but the phone can't be activated. imei unlock is different to Iphone activatio. - your friend unlocked it to use any sim in any country. iOS 7 forces you to restore the phone and reimpit the original icloud login. This can only be solved if you a)forgot the login/changed  it, and can prove to apple youre the owner; b) to get the original owner to deauthorize his account associated with the phone, on his/her computer.
    2)if there's also a Passcode lock on the phone, and the last registered sim doesn't work (in the case of a stolen phone) - then it's impossible for you to do anything, full security = restore will lead to activation lock immediately. There's no bypass to it, the fake videos online only allow a bypass if the device was a 'jailbrokem' one - which would invalidate apple trying/ever wanting to help you.
    if you know who the phone belonged to previously (usually comes up with the icloud username on it) then you can ask them to deactivate it.
    otherwise, you have what we call - a brickb- won't even work as a super iPod touch
    my iphone was stolen on sat in prague - white, 32 gb iphone 5 - if it's mine, I'll have it back please   just incase

  • Getting session has timed out while trying to redeem a gift card. have had no problem in the past.  am running a g4 since 2002 with os 10.4 and itunes 9. have no internet problems and can connect to store ok. so far apple no help keeps blaming it on othrs

    am having trouble for the first time trying to redeem a gift card. Everything same on computer, OS, and internet connection. have been able to redeem other cards. this time am getting "SESSION HAS TIMED OUT" while trying to redeem card. have contacted apple and checked out all their suggestion iE:( must be your connection. typed in code wrong, too old version of itunes, etc) anything but why would a gift card code bee tied to a specific vetrsion of ITUNES. Rediculous!! there has to be others out there that have an older version if itune than i have. has anyone ever had the error "SESSION HAS TIMED OUT" and if so was it corrected?? any information other than apples {change password and give us lots of personal info they probably have) would be appreciated..

    Hello,
    As far as I can see, that Verizon Jet Pack wireless Modem uses WPA2 to connect.
    The Router might complicate things right now.
    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    Is that Interface dragged to the top of Network>Show:>Network Port Configurations and checked ON?
    The Interface that connects to the Internet, needs to be drug to the top of System Preferences>Network>Show:>Network Port Configurations and checked ON.
    If using Wifi/Airport...
    Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

  • I have this message appearing "the application finder has unexpectedly quit while trying to restore its windows"... someone PLEASE help

    I have this message appearing "the application finder has unexpectedly quit while trying to restore its windows"...
    So far it doesn't appear to be effecting anything that i can see on my imac BUT it is incredibly annoying and popping up at bad times, and it all happened when my imac automatically updated itself. So annoying. PLEASE help!!!

    Finder crashes are often caused by "Google Drive." If it's installed, I suggest you first check for an update. If that doesn't solve the problem, remove it according to the developer's instructions. You may need to start the computer in safe mode to do so. Back up all data before making any changes.
    If you use Google Drive and don't want to remove it, then try deselecting the option in its preferences to "show status icons." According to reports, that may be enough to stop the crashing.
    Similar cloud-data clients such as "Dolly Drive," "iDrive," "Open Drive," "Transporter Desktop," and others can cause the same problem.

  • My iPhone 4S has locked up while updating the ios. what do I do?

    my iPhone 4S has locked up while updating the ios. what do I do?

    Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. Then try it again.

  • HT1937 My new iPhone 4S has no service, have tried the troubleshooting it was no help, what can I do?

    My new iPhone 4S has no service, have tried the trouble shooting it was no help,

    Try a payphone, landline, or borrow a phone from a friend or relative.
    Or you can email your carrier - try using google.

  • Server Error - While trying to reset my ePrintCenter Password

    Server Error - While trying to reset my ePrintCenter Password.

    Hello @cameronweir73 ,
    Welcome to the HP forum.
    I understand you are getting a server error when you try to reset your password.
    I would like to help.
    Have you tried another web browser?
    You could also call the Cloud Services Department.
    They should be able to get the password reset.
    Please call our Cloud Services at 855-785-2777.
    If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    Hours:
    Mon-Fri. 8am - 11pm, Sat. 9am-8pm - EST
    Mon-Fri. 7am - 10pm, Sat. 8am-7pm - CST
    Mon-Fri. 6am - 9pm, Sat. 7am-6pm - MST
    Mon-Fri. 5am - 8pm, Sat. 6am-5pm - PST
    Aardvark1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!

  • My airport extreme (generation 5) was set up using wifi and has worked flawlessly (on macbook pro 2 iphones and window 7 HP pc)until recently. I have reset to factory defaults over and over but still cannot get on the internet. Any suggestions?

    My airport extreme (generation 5) was set up using wifi and has worked flawlessly (on macbook pro 2 iphones and window 7 HP pc)until recently. I have reset to factory defaults over and over but still cannot get on the internet. However I can then take my DSL cord and insert it in a different Ethernet port other than the WAN port and I can get internet on my Mac and iphones but only wifi on my husband's PC.  I hate to spend another $179 if this is just something I'm doing wrong. Please help

    I'm having a bit of trouble confirming that the ZyXEL is a combination modem & wireless-N router. If it is, then you really won't get any advantages of using the 802.11g AirPort.
    If the range of your ZyXEL is limited, you may find that doing either or both of the following will help: 1) Move the ZyXEL so that it is higher vs. lower in the room, that is away from any closed areas or placed in a metal cabinet, and 2) Changing radio channels. The latter is especially important in you live in an area where there are a number of competing Wi-Fi.
    A good utility to find out, is iStumbler. You would use this to find these other Wi-Fi and find which have the strongest signal value. Those that do, you would also want to note which channel they are operating on, and then, change yours to one that is at least 3-5 channels away. So, for example, if you find strong ones on channels 1 & 6, change yours to 11.

  • Mac and iPad connect to wifi, iPhone will not. I have tried all resets besides the full erase reset and nothing seems to work. Any suggestions?

    Mac and iPad connect to wifi, iPhone will not. I have tried all resets besides the "erase all contents and settings" and nothing seems to work. Any suggestions?

    http://support.apple.com/kb/HT1414
    I would honestly try this. It is how to restore your phone and see if it works.

  • HT201412 My Ipad has frozen I have tried to reset by pressing the sleep and Home. still frozen???????????

    My Ipad has frozen I have tried to reset by pressing the sleep and Home. still frozen???????????

    Try a reset a few more times.
    1. Hold the Sleep and Home button down (together)
    2. For about 10 seconds
    3. Until you see the Apple logo (very important)

  • Ipod has a white screen . tried to reset it. did not work. just lost all of my music

    ipod has a white screen. tried to reset it. still has a white screen and now all of my music is gone

    Hi PINKPASSION,
    If you are having issues with your 2nd Gen iPod Nano, you may want to try the troubleshooting steps from the following page:
    iPod nano (2nd generation) Troubleshooting Assistant
    http://www.apple.com/support/ipod/five_rs/nano2gen/
    Regards,
    - Brenden

  • Thinkpad twist (s230u) bad sectors and trying to reset to factory software

    Hi all
    My thinkpad suddenly not starting. During bootup, I tried to scan and fix sectors but after 3-4 hours, it said it can not be done (after finding like 400 errors). May be the hard drive is partially corrupted. I tried to reset to factory setting from within startup screen it went till 42% and hung for two days. When I restarted it can not now complete even factory reset.
    Is there a way I can get factory os installation and settings from online lenovo website? Any help is appreciated.
    By the way my laptop is out of warranty.
    Thanks
    Anil
    Solved!
    Go to Solution.

    Good day and welcome to the community.
    Sorry you're having difficulty.
    Your best bet would be to call Support (info below) to request recovery media, as it is not available as a download.
    Hope this helps.
    Regards.
    United States
    THINK-branded products
    English
    1-800-426-7378
    24 hours a day 7 days/week
    Software Premium Support - Windows & Android Operating Systems
    English
    1-855-271-3879
    8AM-11PM Eastern, daily
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество
    Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
    PM requests for individual support are not answered. If a post solves your issue, please mark it so.
    X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
    I am not a Lenovo employee.

  • I have a cp1215 has started to be extra slow have reset to factory defaults and reinstalled driver

    I have a cp1215 has started to be extra slow have reset to factory defaults and reinstalled driver on the computer etc....
    I think where it is taking the most time is in the deleting from the print queue.  I have an HP desktop computer with 3gb ram on windows xp. even if all I am doing is printing a test page with no other programs started it takes for ever to print a page.
    any help would be appreciated

    Hi Mikeryan,
    Have you tried turning off bidirectional communication?
    Open your printers and faxes folder, right click the icon for your printer, and choose printer properties.
    Go to the ports tab, and un-check "Enable Bidirectional Communication".
    Restart your computer, and try printing to see if the issue has been resolved.
    Hope this helps
    I am an HP Employee
    Click the KUDOS Star to say "Thanks"
    Please mark the post that solves your problem as "Accepted Solution"

  • Wifi just stopped working on an iPhone 4S, iOS 8.1.3. Have reset to factory  settings and restored, still no wifi.

    Wifi just stopped working on an iPhone 4S, iOS 8.1.3. Have reset to factory  settings and restored, still no wifi. Will next release of iOS address this problem?

    Hey there kevin8!
    I have an article for you that can help you continue to troubleshoot this issue with the Wi-Fi on your iPhone. The article can be found right here:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Hopefully that will help resolve your issue. Thanks for using the Apple Support Communities!
    Cheers,
    Braden

Maybe you are looking for

  • Can't add anything to sidebar

    I'm running Lion- I can't add anything to my sidebar. I have EVERYTHING checked when i go to Finder-Preferences, but nothing is showing up. I can't drag anything in there either. What the F?

  • How does preparedstatement work?

    In jb9 online book, it said "An object that represents a precompiled SQL statement. A SQL statement is precompiled and stored in a PreparedStatement object. This object can then be used to efficiently execute this statement multiple times. ". But in

  • Fingerprint Reader Support

    Does anybody know if Snow Leopard has drivers for fingerprint reader devices, in particular the Microsoft USB Fingerprint reader?

  • Problem in Live View

    I have my screen split with code on the left and comp on the right.  When I hit Live button, my code window goes away.  Is there a way to prevent this from happening?  I would like to stay in Live view and code.

  • Help! RMI throws NoSuchMethodError

    Everything goes fine. The rmiregistry starts, server code starts. The binding takes place properly but when u do Test test = (Test)Naming.lookup( "rmi://localhost/test") it gives this : Exception in thread "main" java.lang.NoSuchMethodError: stub cla