My iPhone 5 alternates between ringer and silent, when on "ringer".

Is anyone able to advise a solution to iPhone 5. When on Ringer, it cycles continuously between silent (with vibrate enabled or not) and "ringer". I have reset the device which has not resolved the problem. But, it has kept me occupied resetting my personal settings.
thank you in advance

Thanks, I'll prob just do it myself. My phone's too old so I doubt they'll do anything for free.

Similar Messages

Powerbook alternates between battery and adapter when plugged in

The other day my PB started alternating between battery and adapter when plugged in: the symbol changes from batt to charging every few seconds, brightness goes up and down. I've managed to find a position where it will actually charge. I even tried a new adapter, but it's still extremely temperamental.
I'm afraid there's something wrong with the internal power jack, but is there anything else it could be? Any way to tweak the jack?
Thanks!

No, there's no way to "adjust" the port. It's soldered to a small Sound/DC-In card inside the Powerbook. What's apparently happened to yours is that the cord has been jerked rougly up, down or sideways one time too many, and one or more of the solder joints has broken. Because it's now able to move, however slightly, the rest of the joints are also being stressed every time you connect or disconnect the cord. Sooner or later another will break, then another. You'll end up having to replace the card when you can no longer shim or jimmy the port so it makes proper contact.
If you're very good at very small-scale soldering, you could take the card out and try to repair it, but if you're an average ham-handed Joe like me, replacing the board is a better bet. Getting to it, while not actually difficult, is a pretty considerable adventure in an Albook, because nearly everything else has to be removed from the case first to reach it.

Optimizing iPhone battery life: Between charges and before replacement

FYI. An excellent iPhone battery care article by iPhoneAtlas.com:
Optimizing iPhone battery life: Between charges and before replacement
http://www.iphoneatlas.com/2007/07/09/optimizing-iphone-battery-life-between-cha rges-and-before-replacement/

OK, I agree that is a completely false statement. The rest of the article is pretty good.
If you assume a linear decrease in battery charge for each full cycle (which it really isn't, but much easier to model in a spreadsheet). Then 80% of original charge after 400 full cycles is approximately 0.8% loss in battery charge per full charge cycle (again this is a simplification, stay with me). This means that after 400 cycles, you are at approximately 80% of your original total charge level. As stated by Apple.
So, extrapolating that out to EOL (end of life) which Apple assumes to be 50% battery charge, it would take approximately 1,000 full charge cycles for your battery to be EOL (according to Apple). It would actually be slightly less than that since it won't be a linear function.
For me, that's 2 to 4 years of use depending on whether or not I continue using the iPhone as much as I have this first full week.

Iphone 5 rotates between vertical and horizontal modes, but does not flip vertically.

New Iphone 5 rotates between vertical and horizontal modes, but does not flip vertically.
Tried restarting, checked the lock, gyroscope.

Hey Oprion,
Thanks for the question and congrats on your new iPhone 5c. The orientation of your iPhone will depend on the application you are using. For example, most of the built in applications only support the three main orientations (Horizontal, Vertical, Horizontal), whereas the Voice Memo’s application will operate “upside down” for easier access to the microphone.
Change the screen orientation - iPhone
http://help.apple.com/iphone/7/#/iph3badf94ec
Thanks,
Matt M.

Why does my email address and text message alternate between mine and my husbands name?

Whenever I send an email or a text message, the name of the sender alternates between me and my husband - I'm so confused!

Hello,
Mail Preferences>Composing>Addressing:... is Send new Mail from set to a specific address or from Account of last viewed mailbox?
In Address Book do you have a combined entry for you & husband?

Macbook Pro alternates between charging and not charging

Hello,
I have a 15-inch Late 2011 MBP, and the problem that I am currently having, is when I am charging my MBP from a relativly low charge, or when I am charging it as well as running a highly demanding program, the power adapter will get extremely hot to the tuch, and my computer will then alternate between charing and not chargin. When the computer is aternating between charging and not chargin, the light on the Magsafe connector will be orange (like a normal charge), then it will go out (like I unplugged the addapter from the wall), then it will turn green (like when it is fully charged/or when you first connect it to the computer before it startes chargeing), then it will go back to Orange for a few (~10-15 seconds), then it will start the cycle all over again.
         Some side information that might help: This is my second charger for this computer, the cord right behind the Magsafe conector fell apart after a few months; I did however replace if with an Apple 85W power adapter (no offbrand/knockoff). Also, the grounding plug on the extension broke off a while ago, however I did use this same extension (the original that came with my computer) with the original addapter which I had absolutly no problems with (appart from falling appart after a few months).
          I am considering getting a new Extension for my computer, because i beleace that the fact that there is no ground is causing static/buzzing when i use headphones, though I bleave this is not realted to my power adapter problem.
          So, do you think I should just replace the entire addapter and extension? I wanted to ask here first, because I do not want to get a new addapter if it is going to do the same thing again.
          Thanks for any addvice!

First, if your computer is under Applecare, so is your charger. If it is, just take the charger and computer to the Genius Bar and they'll take care of it. If it's not, you still might want to make the trip to the Genius Bar. The eval is free, and you'll find out exactly what your problem is. Not to mention that you're in the right place to buy another one if you need to.

HT4623 hi..i just bought an iphone 5 yesterday 32GB..and now when i am trying to update the software..it says the following: unable to check for update/an error occurred while cheking for a software update...please help me..is it a problem in my new iphon

hi..i just bought an iphone 5 yesterday 32GB..and now when i am trying to update the software..it says the following: unable to check for update/an error occurred while cheking for a software update...please help me..is it a problem in my new iphone??or it's just an temporary error in the apple software center???

Lyndsay237 wrote:
This device does not have a sim card in it. Could this be the reason or am I missing something when I am trying to update.
Yes. You can't update or restore any GSM iPhone without a valid sim card installed in the phone. The sim card need not be activated, but it must be valid & present. If you want to update, you need to get a sim card.

In Mountain Lion how does OS select between ethernet and WiFi when both are activated??

In Mountain Lion how does OS select between ethernet and WiFi when both are activated?? How does OS use "both" networl accesses??

It will pick the highest service in the list which has an internet connection.
To order the list, open Network System Preferences and select Set order of network services from the button below the service list.

What are the configuration need between R3 and XI when we use RFC sync adap

hi,
What are the configuration need between R3 and XI when we use RFC sync adapter.
Regards
siva.

if its the sender adapter ref:
RFC adapter
Sender- /people/michal.krawczyk2/blog/2005/03/29/configuring-the-sender-rfc-adapter--step-by-step
Receiver;
http://help.sap.com/saphelp_nw04/helpdata/en/c8/e80440a832e369e10000000a155106/content.htm
Also;
trouble shooting rfc/soap -
/people/shabarish.vijayakumar/blog/2008/01/08/troubleshooting--rfc-and-soap-scenarios-updated-on-20042009

How does iPad choose between wifi and 3G when both are 'on'?

Easy peasy question.
I have 02 and Wifi going on my iPad. I know I can use 02 out and about and I know I can use wifi at home etc.
But when I'm at home how do I make sure I'm using my wifi for data and not my cellular connection???
I've been turning my cellular to 'off' when at home, just in case, but I don't want to have the faff of turning it off and on, so it would be nice to know how the iPad chooses between wifi and 3G when both data access points are active.
Also I've had no wifi troubles at home at all. so far... The acid test will be setting it up at work as they have proxyies for everything, but obviously I don't have proxies at home. I'm not sure if the settings screen can cope with different proxies dependent upon different wifi networks... * grin *

In the status bar I have
a signal strength indicator then 'O2-UK' then the 'fan' No mention of 3G.
I'm guessing you're going to say that when 3G is showing then 3G is being used for data?

Difference between CS3 and CS4 when placing images, percentage not kept

There is some kind of difference between CS3 and CS4 when placing images. The images I've dealt with right now were vector images but it might apply to all kinds of images.
When replacing an existing image, the CS4 behaviour is to let the image fill up the frame. In CS3 the percentage was set to 100% as default (the % you see when selecting the image, not the container).
Also when replacing an impage in CS4, the "inner" image frame is kept, while in C3, the percentage was kept.
Is there some kind of placement preferences / settings to let CS4 act the same wat as CS3 did, when placing an image?
-- Andreas

Yes, the behavior was changed in CS4 (and many users, like me, prefer the new system).
If you click and drag a loaded image place cursor the entire image will be be scaled to fit the proportionally drawn frame -- a huge timesaver if you mostly place uncropped art. If you want 100% of the image at 100% scale, just click and release -- same as before, or as before you can pre-draw a frame and place into it and your image will come in cropped at 100% (unless you've changed the fitting options for the frame before placing).
Peter

Display alternates between dark and bright

I have several issues but I suspect somehow they are all related as they all began about the same time, within about an hour of each other, which was maybe a week ago.
Periodically, my display slowly cycles between dark and bright. Sometimes the display will suddenly go to sleep on it's own, usually after a period of about 20 seconds of me not doing something and when I wake it up the display is quite dim. Other times the computer goes to sleep (not just the display) requiring me to log back on. I use password for startup. I open the display settings after log-on and the brightness slider has somehow moved way over to the dark end (left). I slide it up to where I like it and soon it does it again all by itself again after a very short period of inactivity. I have noticed that if I leave the brightness control alone (dim) without readjusting it it seems to take longer for the other issues to develop. I would normally place the brightness slider just under half way up. My sleep time settings are currently: computer - 1 hr, display 15 min. That is plugged in which is pretty much the only way I ever seem to use it ... plugged in.
Another issue is an occaisional rapid beeping. It's the same low beep that you hear when you try to do something stupid and the computer is telling you you've made an error. The difference is this is a long, unending string of rapid beeps; I'd estimate maybe 15 - 20 beeps per second. The sound does not stop. I have to mute the speakers to shut it up. I have not yet been able to determine a recognizable pattern of common variables for when this happens. The other day when the computer went to sleep by itself and I woke it and tried to input my password and I saw that the input bar was filled with black balls as if it was remembering my password which I did not like but when I hit enter the logon dilaog box shook, the entry field emptied and refilled on it's own. I held the backspace key for several seconds and nothing seemed to happen. I used shift/command/arrow to highlight the entire string and deleted it but as soon as the characters were deleted I saw the input line quickly fill back up again one ball at a time at roughly the same rate as the beeps. Then it occured to me that the beeps were similar to those you would hear if you held a key down and filled an entire entry field with a hundred of a particular character and was still holding down the key long after the field was full. My first thought was that a key was stuck down. Not so. Each and every key is free to move and functions normally.
Last night I closed the lid to put the computer to put it sleep before I went to bed. About 3 hours later I was awakened by the sound of the rapid beeping. I got out of bed and went to the computer and opened the lid to find the same input line black balls issue but this time it was accompanied by the beeping and the display was also cycling between bright and dim. As it was the middle of the night I killed the machine by holding down the power button and forcing a shutdown. This evening I decided to do the upgrade from 10.9.1 to 10.9.2 hoping that might help but it did not. I have not heard the beeping since the upgrade but the display is still cycling, which was the first thing I noticed when all of this began.

Turns out it may have been sofware issue. I suspected software anyway because rebooting could temporarily cure it. I spoke to an Apple Service and Support person on the phone. She went through a fairly lengthy process with me to evaluate the machine and determine if it was hardware or software related. The results of those steps did not lead her to any concrete conclusions but she was able to hear the beeping issue happening in real time. She guided me through the steps of O/S recovery and now several hours later the machine appears to be functioning as it is supposed to. Typically the issue(s) would show up after maybe twenty minutes or a half hour after a hard boot. I am to monitor the thing for the next week or so watching for any signs of the issues slowly returning.
Here's keeping my fingers crossed.

Usage in My Verizon alternates between used and available

At least that is what it appears to do. When I refresh the screen in My Verizon, it appears to flip between used and available.
Very Strange Behavior indeed...

I'm not sure what you mean by "flip between used and available" - I have a line graph that is the total allowance, then a green bar indicating usage... the numbers on the right show what I have used out of my total allowance, and the graph is a visual representation of the numbers.
See photo:

I can not install Itunes 10.5 on vista or windows 7 my iphone 4 is much slower and freezes when i go to the store they turn me away with my laptops and tell me to buy there computer thats the only answer. I know there has to be away around it?

I ca not install Itunes 10.5 on vista or windows 7 my iPhone 4 is much slower and freezes and also certain apps and also certain features will not work on the phone now that I cannot update it to ios5. When I go to the store they turn me away with my laptops and tell me to buy there computer that's the only answer. I know there has to be away around it? I am also up for a new upgrade on my second phone line and was going to get a 4s but now I am thinking it may be the wrong choice I am very unhappy with Apple right now...

WOW! That font is difficult to read. But, see if this support document helps you http://support.apple.com/kb/TS3989. Photos stream is based on date and photos more than 30 days old are removed. Photostream is designed as a temporary storage to allow you to download the photos to the computer.

My iphone email not showing attachment and signature when send out to anyone ?

email not showing attachment and signature when send out to anyone ?

This is what I did:
How to put iPod touch / iPhone into DFU mode
A small guide on how to put your iPod touch / iPhone into DFU mode. Works with all G’s of iPod touch / iPhone
What is DFU: Device Firmware Upgrade
Step 1: Turn off your iPod touch / iPhone completely and connect to PC / mac
Step 2: Hold down the Power button for 3 seconds
Step 3: Without releasing the power button, also hold the Home button for 10 seconds
Step 4: Without releasing the home button, release the power button and keep holding the Home button for 20 seconds.
Itunes will identify that you are in DFU mode.
That's when I got the black screen with USB and iTunes icons. iTunes itself, did not show my phone.

My iPhone 5 alternates between ringer and silent, when on "ringer".

Similar Messages

Maybe you are looking for