My iphone isnt recognized after trying a firmware update

My iphone 3 started to restart itself about 3 days ago, and then quit charging about the same time,did a firmware update, but received an error 29 that i couldn't do the updates, it suggested a restore so it could respond with itunes, tried the restore, that also failed, left my screen with a itunes logo and USB cord, tried several times for restore didn't work, today the phone is not even recognized by either of my computers, the itunes logo is gone and there is a slow flashing apple on the screen when I plug it in.....USB or electric to charge,,,, any suggestions,, i am 40 days past my warrantee go figure,,,,,,,,,,,,,,

Iphone 3g can only go to 4.2.1

Similar Messages

  • Not Able To Print w/ Lexmark X2600 After Recent Airport Firmware Update

    Hi,
    So, after the recent firmware update for the Airport Extreme (802.11n), I can no longer print to my printer share. The device is recognized in Bonjour, and I use the correct driver as I did before, but when I send something to the printer, it just reads:
    "Connecting to MyNetwork.local...
    There is a problem communicating with the printer. Make sure the printer is powered on and connected to the computer. Delete or hold the job and try again."
    Now, if I connect the printer directly to my computer and set it up with the same drivers over USB, it works just fine. Can I get some support on this?

    Hi,
    Have you tried this?
    To change the printer’s network settings:
    1. Open the printer's embedded Web server.
    2. Click the Networking tab. For wireless settings, click Wireless. For IP settings, click IP
    Configuration.
    3. Change the printer's settings to match the settings of the network, then click Finish.
    4. Close the printer's EWS, then disconnect the Ethernet cable from the printer.
    5. The control panel lights will cycle.
    The previous procedure is from the Wireless Printer User Guide for your printer.
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • I have a Iphone 4 and after the last software update iOS.0.4, my phone is no longer connecting to the wifi at my house.

    I have a Iphone 4 and after the last software update iOS.0.4, my phone is no longer connecting to the wifi at my house.
    My MacBook Air is connected and my roommates phones are also connected, but my iphone that always was connected to the same network is no longer connecting to the wifi.
    The network is shown on the device but I can't join it.
    Whats going on? Does someone know how to solve this issue?
    Thank you!

    Problem persisted after fixes were done so wife called apple today.           Their fix is to turn cellular off when in the house and turn it back on when she leaves- the 4 doesn't keep the password so she has to enter the password too... This wasn't a fix ...it's just resolving the connection problem... They also said that they made ios6 have security features so nobody can hack into the wifi without having the password and it has to be entered to use the wifi.  My 5 and the iPads stay on with no problems.  It's just the 4.        So far so good...she's had wifi all day when home.    It's inconvenient but it's either completely reboot it with iTunes (which doesn't work for her) or buy a new phone and she won't do that either.
    So...Apple is saying that she didn't have to do the updates either and could've stayed with the previous iOS     but !!!too late now!!!  We've updated because we think our phones will run better but the ios6 just made it a pita for users
    I wonder if the hackers of the world are having as many issues as the peeps who are just trying to use their wifi??

  • Iphone 5 issues after IOS 8.2 update: my husband's phone and my phone get the same phone calls ONLY when we are home.  Any suggestions on where to look to fix this?

    Iphone 5 issues after IOS 8.2 update: all the iphones in the house receive the same phone calls ONLY while we are at home.  Any ideas on how to fix this?

    That is a new "feature" described in Connect your iPhone, iPad, and iPod touch using Continuity
    You can turn it off by going to Settings > FaceTime and changing "iPhone Cellular Calls" to off

  • After trying to install update on MacAir error message and then message saying panic (cpu caller 0xffffff800a859241): "Unable to find driver for this platform: \"ACPI\".... I'm worried as all of my work is on my computer and I'm afraid I will lose it all.

    I am totally worried I am going ot lose all my data after trying to install update on MacAir.  Cannot do anything error message saying panic ....."Unablet o find driver for this platform."

    Hi Guys
    No good news I'm afraid. I have been through ALL the system caches and files that were updated at the time of said issue. Reset - rebuild and even gone back to my TimeMachine copy from earlier this AM. Nothing! Can only assume it is something deeper in the /usr or var or private folders.....
    I have cloned the system and core files (/usr, /private) etc etc to an external HD and it still recreates the fault. I am afraid to say I have no more time at the minute to look at so have put my machine back to 2 hours prior via my TimeCapsule.
    I the absense of anyone else or, indeed, Apple fixing in the next 12 hours, will get back onto it from the cloned copy I have kept and see if I can find the offending file/files...
    Sorry I don't have an immedaite solution.

  • Any plans to fix wireless networking after the 40S51U Firmware Update 2.2.5 broke it?

    After the 40S51U Firmware Update 2.2.5 wireless passwords must be re-entered every time the device is powered on. It's been almost 4 months since the untested patch was released – is a fix coming?

    You're the only person I can remember having that issue. You should call customer support.
    - Peter

  • IPhone not recognized after Mac security update

    I have a Mac iBook G4 running OSX 10.4.11, and an iPhone 3G running OS 3.0. Up to now they have worked fine together. The phone was charged on the iBook this morning. This afternoon I ran software update on the Mac which installed the latest security update (2009-05, I think). After that, the phone is not recognized when plugged in the USB port. It no longer charges, nor is it recognized by iTunes.
    I have checked the following to be sure that the security update is the culprit:
    The iPhone with the same cable works fine on another Mac (running 10.5).
    Other devices (thumb drive, printer) work fine in the same USB ports.
    Finally, I restarted the iBook from the original installation CD for OSX 10.4. When running with the original version, the iPhone is recognized correctly.
    So, I am reporting a problem with the security update, and I need to know how to back it off, or how to get it fixed.
    Thanks for any help.
    NOTE: Software update also installed iTunes 9.0.1 along with updates to Quicktime and Safari. However, none of these apps even have to be running to show that the phone will not charge.

    The problem was solved by resetting the System Management Unit, thanks to a helpful phone call with an Apple Expert. On the iBook this required unplugging, removing the battery, and holding the power button in for 15 seconds.
    Earlier I tried zapping the PRAM, as someone suggested, but the phone was not recognized. But it turns out it did show up in the System Profiler.
    I have no idea why this happened in the first place, right after the software update.

  • Iphone not recognized after upgrading to itunes 8.2

    Phone not recognized in itunes after the 8.2 update, is this a bug?

    Ok, I've found a workaround on another thread (http://discussions.apple.com/thread.jspa?messageID=9658855).
    According to that poster (he has an iPod Touch), Apple Tech Support told him to disconnect his computer from the Internet, and then try to connect his iPod Touch. This worked for him. I just tried it and it works reliably.
    After reading the post I plugged out my Internet connection from my laptop, and then connect my iPhone. It was detected. I repeated this 4 more times and each time the device was detected and came up in my iTunes sidebar. I then restarted my machine and tried it again 5 times. It worked all 5 times. When I reconnected my machine to the Internet, the problem came back the very next time I plugged my phone in.

  • Iphone went off after trying to update to iOS 8.1.3

    My iphone went off while trying to update to iOS 8.1.3

    Hey cliffordmien, 
    That is not good so lets see if we can get it back up for you. Try restarting your iPhone and try the update again. If you still have issues then you may need to update your iPhone through iTunes. If you restart your iPhone and it is booting up to the plug in to iTunes graphic you will need to restore it with iTunes. 
    Resolve issues with an over-the-air iOS update
    http://support.apple.com/en-us/TS4431
    If you can't update or restore your iPhone, iPad, or iPod touch
    http://support.apple.com/en-us/HT201263
    Take care,
    -Norm G.

  • Anyone unable to connect to bluetooth devices on iphone 4 GSM after 4.3.5 update?

    After I updated my iphone 4 to 4.3.5 firmware I have not been able to connect to any bluetooth devices.  Also what is strange is that I also updated my wife's 3GS to 4.3.5 and she cannot connect to any bluetooth devices eitherl.  When I search for anyone else having this issue I find nothing.  Anybody?

    cliffsnotez wrote:
    After I updated my iphone 4 to 4.3.5 firmware I have not been able to connect to any bluetooth devices.  Also what is strange is that I also updated my wife's 3GS to 4.3.5 and she cannot connect to any bluetooth devices eitherl.  When I search for anyone else having this issue I find nothing.  Anybody?
    I have no bluetooth problem after updating to 4.3.5. Have you tried un-pairing the devices, then pairing them as new devices? Have you tried Reset Network Settings? And have you seen this: iOS: Wi-Fi or Bluetooth settings grayed out or dim

  • IPhone acting wierd after 1.1.3 update.

    After the new software update, my iPhone screen stops responding randomly. It only happens while I'm on safari and the iPod. It only happens rarely on the iPod, but when on safari, it happens enough to be a nuisance. Is this a problem other people are having or is it my iPhone itself?

    Have you tried the troubleshooting steps in the order I provided with my first post in this thread with the last being calling AppleCare or making an appointment at an Apple Store?
    This is not normal except for getting slow to think from time to time with powering the iPhone off and on - which should be done with a GSM phone every few days or so regardless or a Reset which should take care of this aspect.
    I power my iPhone off and on each morning before beginning the day and I usually do a Reset once a week or so just to keep things running smooth.

  • 27" iMac very sluggish after recent software/firmware update

    I bought my 27" iMac (2.7 GHz Intel Core i5, 4GB RAM) maybe 6-7 months ago...and it has had NO problems. Even after updating to Lion. Smooth.
    But after the most recent graphics firmware update (Feb 29) and software update (late Feb/ealry March 2012...can't remember exact date)...now my iMac is so sluggish! Running more than one application really makes my iMac run slow. And I'm not talking about Photoshop...I'm talking about Firefox, Safari, Mail, iTunes. Basic ones. Especially bad when I play video...very choppy.
    Any clue what's going on? I ran Disk Utilitiy (all good, repaired permissions), Clean My Mac, CCleaner...all say good and healthy. So I am at a loss.
    Any help would be greatly be appreciated. I'm still under warranty...but I don't think I need to bring it in do I?
    Thanks!

    Hi Linc Davis,
    I am trying the Terminal commands as you suggested. I am copying and pasting the output below:
    Step 1 output:
    com.Cycling74.driver.Soundflower (1.5.1)
    Step 2 output (after password):
    com.microsoft.office.licensing.helper
    com.machangout.glims.loader
    com.citrixonline.GoToMyPC.CommAgent
    Step 3 output:
    com.citrixonline.GoToMyPC.LaunchAgent
    com.adobe.CS4ServiceManager
    com.macpaw.CleanMyMac.volumeWatcher
    com.macpaw.CleanMyMac.trashSizeWatcher
    com.macpaw.CleanMyMac.helperTool
    com.google.keystone.user.agent
    Step 4 output:
    /Library/Components:
    /Library/Extensions:
    /Library/Frameworks:
    AEProfiling.framework
    AERegistration.framework
    Adobe AIR.framework
    AudioMixEngine.framework
    GlimsAdditions.framework
    HPDeviceModel.framework
    HPPml.framework
    HPServicesInterface.framework
    HPSmartPrint.framework
    NyxAudioAnalysis.framework
    PluginManager.framework
    iLifeFaceRecognition.framework
    iLifeKit.framework
    iLifePageLayout.framework
    iLifeSQLAccess.framework
    iLifeSlideshow.framework
    net.juniper.DSApplicationServices.framework
    net.juniper.DSCoreServices.framework
    net.juniper.DSNetworkDiagnostics.framework
    /Library/Input Methods:
    /Library/Internet Plug-Ins:
    .DS_Store
    AdobePDFViewer.plugin
    Flash Player.plugin
    GlimsAdditions.webplugin
    JavaAppletPlugin.plugin
    OfficeLiveBrowserPlugin.plugin
    Quartz Composer.webplugin
    QuickTime Plugin.plugin
    SharePointBrowserPlugin.plugin
    SharePointWebKitPlugin.webplugin
    Silverlight.plugin
    flashplayer.xpt
    huludesktop.webplugin
    iPhotoPhotocast.plugin
    net.juniper.DSSafariExtensions.plugin
    nsIQTScriptablePlugin.xpt
    /Library/Keyboard Layouts:
    /Library/LaunchAgents:
    com.adobe.CS4ServiceManager.plist
    com.citrixonline.GoToMyPC.LaunchAgent.plist
    com.machangout.glims.agent.plist
    /Library/LaunchDaemons:
    com.apple.remotepairtool.plist
    com.citrixonline.GoToMyPC.CommAgent.plist
    com.machangout.glims.loader.plist
    com.microsoft.office.licensing.helper.plist
    /Library/PreferencePanes:
    Flash Player.prefPane
    GoToMyPC.prefPane
    Perian.prefPane
    /Library/PrivilegedHelperTools:
    com.microsoft.office.licensing.helper
    /Library/QuickLook:
    GBQLGenerator.qlgenerator
    iWork.qlgenerator
    /Library/QuickTime:
    AC3MovieImport.component
    AppleIntermediateCodec.component
    AppleMPEG2Codec.component
    Perian.component
    /Library/ScriptingAdditions:
    Adobe Unit Types.osax
    Glims.osax
    /Library/Spotlight:
    GBSpotlightImporter.mdimporter
    LogicPro.mdimporter
    Microsoft Office.mdimporter
    iWork.mdimporter
    /Library/StartupItems:
    Aladdin
    /etc/mach_init.d:
    /etc/mach_init_per_login_session.d:
    /etc/mach_init_per_user.d:
    Library/Address Book Plug-Ins:
    SkypeABDialer.bundle
    SkypeABSMS.bundle
    YMsgrCallABPlugin.bundle
    YMsgrMsnABPlugin.bundle
    YMsgrSmsABPlugin.bundle
    YMsgrYimABPlugin.bundle
    Library/Fonts:
    Library/Input Methods:
    .localized
    Library/Internet Plug-Ins:
    BrowserPlus_2.9.2.plugin
    GlimsAddition.notplugin
    Picasa.plugin
    Library/Keyboard Layouts:
    Library/LaunchAgents:
    com.apple.AddressBook.ScheduledSync.ABExchangeSource.1B4BA2C7-8ACA-4857-8BDE-B6F 9698BABA2.plist
    com.apple.AddressBook.ScheduledSync.PHXCardDAVSource.1F0D2067-5983-4134-AD50-A70 652DAED7C.plist
    com.apple.AddressBook.ScheduledSync.PHXCardDAVSource.A4130F93-370D-42FD-86A0-CD8 4B1494812.plist
    com.google.keystone.agent.plist
    com.macpaw.CleanMyMac.helperTool.plist
    com.macpaw.CleanMyMac.trashSizeWatcher.plist
    com.macpaw.CleanMyMac.volumeWatcher.plist
    Library/PreferencePanes:
    BrowserPlusPrefs.prefPane
    Growl.prefPane
    Step 5 output:
    2012-03-11 22:38:01.741 osascript[408:707] Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    osascript: OpenScripting.framework - scripting addition "/Library/ScriptingAdditions/Adobe Unit Types.osax" declares no loadable handlers.
    GrowlHelperApp, Skype, Nokia Multimedia Transfer, Quicksilver, Dropbox
    Ok...I hope you can see if there are some 3rd party apps that are slowing down my system Linc Davis...please let me know okay?
    Thank you very much for your assitance!!!

  • Freeze at startup after System and Firmware update - Help!

    I took the automated system upgrade last Sunday including updates on a bunch of Apple applications, OS X 10.4.6 (it was included if I recall correctly) and a SMC Firmware update. After downloading all files and installing them my iMac restarted. After that the SMC Firmware upgrade started and I followed the instructions ending in another restart.
    This is where my problems began. At this startup I got through the grey screen with the Apple logo and got so far as to the blue screen with the Mac symbol saying something like "starting up". The progress bar started moving and froze after reaching about a fifth of its final length.
    As this was a firmware update I didn't want to interrupt anything so I left it for the night (no progress in the morning) and for the next day. Still no progress when I came home from work so I shut it down (pulled the power cord).
    Efter this I've tried to fall back using the Firmware Restoration CD available at Apple's support page, but this doesn't work. My iMac refuses to start the installation of the old Firmware even though I follow the fallback instructions. (After starting the computer and keeping the power on button pressed I wait for the front light below the screen to first flash rapidly for a while and then do a SOS (three short, three long and three short blinks). The SOS however, never happens, instead the computer proceeds directly to the grey startup screen before it freezes when it reaches the blue screen.
    I have no clue to what to do. Any and all help will be greatly appreciated.
    Staffan
    iMac 20" (Intel)   Mac OS X (10.4.6)  

    minxlj,
    It is not my intention to be rude, however, it is my intention to be direct. Do you have a G5 or do you have an Intel Core Duo, or perhaps even both? Because right now your signature says you have a G5, which has PPC chips in it made by IBM, not Core Duo chips made by Intel.
    The reason I ask is because, just as in another Discussion here in the Intel forum, you are responding to information that appears to not apply to the computer you say you have and you are giving information that, if you have a G5, does not apply to the computers of the folks here in the Intel forum.
    Could you please clear that up by correcting your signature so everyone here knows you are comparing oranges with oranges and not mangos with oranges?
    Staffan,
    As far as the SMC Firmware update and the Firmware Restoration CD, the two items are not related. The Firmware Restoration CD is only for the Firmware Update that came out in mid-April. It is intended for someone whose computer messed up in the application of the Firmware Update and is intended to bring their computer back to its Firmware state prior to the botched Firmware Update. It will not assist you if you had problems applying the SMC Firmware Update from early May.
    If I am understanding your description of your Mac's problem it sounds if if you have successfully installed the SMC firmware update, but now have a possible 3rd party satrtupitem that is not allowing your Mac's OS X to fully boot. You can check to see if both the Firmware Update and SMC Firmware Update have been successfully installed by booting your Mac into safe Mode by pressing the "Shift" key during startup. This boot will take longer than normal because it is verifying and repairing your directory. After the desktop appears, go to Apps/Utilities/System Profiler. In the Contents section, highlight Hardware and Hardware Overview should show; Boot ROM Version: IM41.0055.B03 for the Firmware update and SMC Version: 1.1f5 for the SMC Firmware Update.

  • Iphone wont charge after iso7.0.3 update

    I updated my iphone 4s to the current ISO 7.0.3 yesterday morning after my phone had been charging overnight.I had a full battery after the update but when i came to put on charge again last night it wouldnt charge. I have tried 3 different charging stations but nothing is charging it. Can anyone help?

    I have the same problem.  I have an iPhone 4 and after upgrading to iOS 7.03 (my first upgrade to iOS 7), my phone volume is almost inaudible.  I have the same problem with the headphones for phone calls.  Listening to music on my headphones works fine.  I have also done a restore and set up as new phone and it doesn't fix the problem though it wasted 4 hours.

  • Aye have bought an old iphone 8gb phone its not a 3g one and aye can't download any apps because it needs to upgrade to ios4.3 how do aye upgrade my iphone? I have tried checking for updates but it keeps saying its up to date

    Aye need to update my old iphone 8gb its not a 3g phone its the older one to ios4.3 and it won't let me update so aye can't download any apps and aye have tried checking for updates and it says that my iphone is up to date can anyone help?

    To identify your iPhone see:
    http://support.apple.com/kb/HT3939

Maybe you are looking for