My iPhone no longer syncs after iOS 5.0.1 update.

I have an iPhone 3GS (16GB), and ever since I updated to iOS 5.0.1 it has been refusing to sync via USB and WIFI. Apparently it needs an additional 8.32GB of space, despite the fact that nothing's changed with regards to the content being synced. I've attached a screenshot for reference.
Thanks in advance for your help.

I had this issue too. I did an OTA update.
I tried turning off my iPhone, removed and reinserted my SIM and turning it on again a few times without success. I also inserted my wife's SIM, it was OK. When I tried with mine again, it was not. I also tried going in and out of Airplane Mode too without success.
Afte a bit of trial and error, I finally got it to work.
What I did was:
1. Turn off WIFI.
2. Turn off my iPhone.
3. Removed and reinserted my SIM.
4. Turned on my iPhone. Almost immediately I saw the  "3G" indicator and after a couple of seconds, my SIM worked!
5. Turned WIFI back on.
From my issue, it seems the iOS 5.0.1 update got "confused" with the network setup.
HIH.
Andrew

Similar Messages

  • IPhone no longer works after iOS 5.0.1 update

    My iPhone 4 no longer recognizes its SIM card after updating from iOS 5.0 to 5.0.1.
    I followed the instructions in the article on the official Apple support site. Removing and reinserting the SIM card did not help, so I used iTunes to reset the iPhone.
    The result is that after switching on, the iPhone tells me that there is no SIM card in the slot (even if there there is) and that I should insert a SIM card with no PIN lock into the slot.
    I do not have a SIM card with no PIN lock.
    My phone company only distributes SIM cards with a PIN lock.
    What can I do now?

    I had this issue too. I did an OTA update.
    I tried turning off my iPhone, removed and reinserted my SIM and turning it on again a few times without success. I also inserted my wife's SIM, it was OK. When I tried with mine again, it was not. I also tried going in and out of Airplane Mode too without success.
    Afte a bit of trial and error, I finally got it to work.
    What I did was:
    1. Turn off WIFI.
    2. Turn off my iPhone.
    3. Removed and reinserted my SIM.
    4. Turned on my iPhone. Almost immediately I saw the  "3G" indicator and after a couple of seconds, my SIM worked!
    5. Turned WIFI back on.
    From my issue, it seems the iOS 5.0.1 update got "confused" with the network setup.
    HIH.
    Andrew

  • Iphone 4 is rebooting after ios 7.1.1 update

    Hi,
    My Iphone 4 is rebooting and shutting down frequently after ios 7.1.1 update, daily not able to receive calls as it is in shutdown mode and trying to reboot also taking more time, Can some one suggest me the best solution for this problem???

    Hi Sekhar_Nutakki,
    Thanks for visiting Apple Support Communities.
    I recommend these steps if your iPhone is shutting down or restarting unexpectedly:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Best Regards,
    Jeremy

  • IPad will no longer sync after iOS 5 update

    I updated my Original iPad to iOS 5 and now it no longer syncs; it stays stuck at the preparing to backup step. This happens whether I try it via WiFi or via the standard way with the cable.
    I'm thinking I should do a Restore from Backup and get it back to iOS 4.3.5.

    I've been stymied at this backup failure (and thus sync and update since both go through the backup process first) for a long time, ever since release 4.3.3 or thereabouts.
    Stay with me, please; this was part of my recent troubleshooting process.  I tried using the new install of Safari and sure enough, it only loaded blank pages.  iTunes (new release) Help also loaded only blank pages and then reported "computer not connected to the internet".
    In seeking a resolution to the Safari connection issue, I came across this advice from Mike41: "If anyone runs across my post of 7/21/2011 regarding Safari 5.1 not connecting to the Internet on my Windows Vista system, BorisKon suggested I run a command prompt window as administrator and execute the command "netsh winsock reset" (then be sure to reboot). I tried this and now Safari 5.1 can access the Internet. See the discussion athttps://discussions.apple.com/message/15734035#15734035. I had to reboot for the command to take effect. "
    I did this on my system and now Safari, iTunes, and the iPad backup all function 100%.
    Start/Run/"cmd" without quotes.
    Type "netsh winsock reset" without quotes.
    Reboot the computer.
    Happy, happy, joy, joy...

  • My car dock is no longer working after iOS 4.3.2 update...help!!

    I have an after market car dock that normally plays music through my car speakers and charges my iphone. After the most recent iOS update it still charges but does not play music. Any ideas?

    Sometimes after iOS updates older tech or even off brand tech may not be supported. I use an older Griffin car charger with an iPhone & iPad and it won't charge because it is not supported. Maybe get a new dock or an Apple approved product, it kinda irritates me as well not being able to use off brand tech. Its cheaper than brand name products...
    Hope this helped

  • My iPhone 4S Display flickering after iOS 7.0.4 update.How to fix it ?

    Hey am using this iphone for two years now and i had no issue with iOS since i got this flickering screen after updated to ios 7.im tried resetting and restoring .still cant fix it. this iphone is a factory unlocked iphone .i bought from apple store opera france . please help me .how can i fix this issue ? i tried to downgrade for 6.1.3 and itunes doesnt allow to me downgrade even .

    Yes i restored as a new device .but still it doesnt stop flickering . but after ios 7 update only it got flickering problem.other than that iphone was perfecly running smooth without any bugs or errors .cant i dowgrade for ios 6.1.3 ? i tried using tinyumbrella and redsnow .it wont allow me to downgrade .i want to downgrade and see whether its a hardware problem or software problem.

  • Outlook calendar no longer syncs after IOS 7 / iTunes update

    Running Outlook 2003 on Win XP.  Yes that's what IT allows....
    Updated IOS7 (now at 7.0.3), tried to sync on the next day at work.  Itunes forced me to update (11.1.2.31).
    Updated iTunes.
    Notes sync.
    Calendar does not.
    iTunes says:
    Sync Calendars
    Your calendars are being synced with your iPhone over the air
    Over-the-air sync settings cane be changed on your iPhone
    I've disabled OTA calendar sync I know of (Google, iCloud) with no effect.  There are still some iCal feeds that I left on.
    Suggestions appreciated, but I'm stuck with my work environment for now.  Really would like to get back where I was before "updating". :-)

    Still struggling with this.  I did discover a diagnostic in iTunes, but it says all is well.  I suspect that is because it thinks the iPhone is syncing the Outlook calendar over the air:
      Microsoft Windows XP Professional Service Pack 3 (Build 2600)
    INTEL_ DX38BT__
    iTunes 11.1.3.8
    QuickTime 7.7.4
    FairPlay 2.5.16
    Apple Application Support 2.3.6
    iPod Updater Library 11.1f5
    CD Driver 2.2.3.0
    CD Driver DLL 2.1.3.1
    Apple Mobile Device 7.0.0.117
    Apple Mobile Device Driver 1.64.0.0
    Bonjour 3.0.0.10 (333.10)
    Gracenote SDK 1.9.6.502
    Gracenote MusicID 1.9.6.115
    Gracenote Submit 1.9.6.143
    Gracenote DSP 1.9.6.45
    iTunes Serial Number 0013BB300E265908
    Current user is an administrator.
    The current local date and time is 2013-11-08 18:09:43.
    iTunes is not running in safe mode.
    WebKit accelerated compositing is enabled.
    HDCP is not supported.
    Core Media is supported.
    Video Display Information
    NVIDIA Quadro FX 1500
    **** External Plug-ins Information ****
    No external plug-ins installed.
    **** Device Connectivity Tests ****
    iPodService 11.1.3.8 is currently running.
    iTunesHelper 11.1.3.8 is currently running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    Universal Serial Bus Controllers:
    Intel(R) ICH9 Family USB Universal Host Controller - 2934. Device is working properly.
    Intel(R) ICH9 Family USB Universal Host Controller - 2935. Device is working properly.
    Intel(R) ICH9 Family USB Universal Host Controller - 2936. Device is working properly.
    Intel(R) ICH9 Family USB Universal Host Controller - 2937. Device is working properly.
    Intel(R) ICH9 Family USB Universal Host Controller - 2938. Device is working properly.
    Intel(R) ICH9 Family USB Universal Host Controller - 2939. Device is working properly.
    Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293A. Device is working properly.
    Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C. Device is working properly.
    FireWire (IEEE 1394) Host Controllers:
    Texas Instruments OHCI Compliant IEEE 1394 Host Controller. Device is working properly.
    Connected Device Information:
    ----- iPhone, iPhone 5 (CDMA) running firmware version 7.0.3
    Serial Number: -------------- 
    **** Device Sync Tests ****
    Sync tests completed successfully.

  • Calendar not syncing after iOS 4.3.1 update

    Over-the-air calendar synchronization with MS Exchange (Outlook) seems to be broken after upgrading to iOS 4.3.1 (8F190). Worked fine last week with iOS 4.2.1. Both "Push" method and "Fetch" methods are affected. Email synchronization with the same Exchange server is working fine.
    When someone sends a meeting invite, the invite temporarily shows up on the iPod touch calendar until the meeting is accepted on the PC (which causes the invite email to be deleted). At this point, the meeting shows up as accepted on the Outlook Calendar on the PC, but no longer shows up on the iPod Touch calendar.
    I have also tried entering a meeting on the iPod touch calendar and it has not sync'd to the Exchange server. So the syncing issue seems to be bi-directional.
    I'm not seeing any error messages regarding any sort of synchronization problems (actually I'm not sure where to look for such errors), so I'm entering a new topic.

    I'm having the same problem after updating to 4.3 and it's driving me crazy.
    I noticed today when some of the meetings I created on my iPhone were not on the Exchange server and some of the meetings I created in Outlook are not on my iPhone. I turned off calendar sync with my Exchange on the iPhone to clear the entries and turned it back on, but some of the calendar items will not sync no matter how many times I reset it.
    I then decided to check my contacts and sure enough the latest contact I added to my iPhone never made it to the Exchange server. I'm not sure if the Exchange contacts are syncing to the iPhone yet, but I suspect they are not.
    APPLE WE NEED A FIX ASAP! I left BlackBerry for iPhone because of how well the Exchange integration worked, but now it's REALLY BROKEN!
    I am on 4.3 and not sure if I should update to 4.3.1?

  • HT4623 iPhone 4 not working after iOS 6.0.1 update

    I have just updated my phone to iOS 6.0.1, however after the phone updated, it no longer switches on and I just have a grey screen. When I try and plug the phone into iTunes, it does not recognise anything. Is this likely to be a problem due to the updating iOS6.0.1 or has something else liekly to have broken on the phone and it's just pure coincidence that it happened when I did the update?

    I would try a restore in itunes then set up as new iphone (dont use restore from back up) pain I know but it can do the trick.
    Still no luck Apple Store get them to sort it or New Phone Please!

  • Key clicks no longer operating after iOS 4.2.1 Update

    After updating my iPAD to iOS 4.2.1 the audible key click feature no longer works - even though I have it turned on in the Settings panel. Resetting the iPAD did not change this.

    Check the switch formally known as the screen orientation lock. It now mutes all system sounds.

  • Gmail no longer works after iOS 6.1.3 update

    I just updated my iPad 3 to iOS 6.1.3 and immediately noticed that when I tried to open the mail client, it would launch and shut off.  Turns out that I had to delete all of my gmail accounts and then the mail client worked.  I tried to add the gmail accounts back but now I get the following error:
    The IMAP server "imap.gmail.com" is not responding. Check your network connection and that you entered the correct information in the "Incoming Mail Server" field.
    The strange part is that I also updated my iPhone 5 and everything works fine, including gmail!  I check the setting between the two devices and they are the same.
    Apparently, many have reported these types of issues over the past few days.  However, I've yet to see a solution.  Apple hasn't seemed to have responded at all.

    JimHdk,
    Not sure what the issue is...like I said, my iPhone works fine with the 6.1.3 upgrade, the iPad doesn't...only after the updgrade.  Additionally, other's have reported the same issue with gmail.
    https://www.google.com/#hl=en&sclient=psy-ab&q=ios+6.1.3+gmail&oq=ios+6.1.3+gmai l&gs_l=hp.3...626.4887.0.5057.15.15.0.0.0.0.232.1902.4j10j1.15.0...0.0...1c.1.7. psy-ab.O_GfIONYv3U&pbx=1&bav=on.2,or.r_qf.&bvm=bv.44158598,d.dmg&fp=a4b1ae1098b9 eca0&biw=1486&bih=683

  • IPhone 4 total malfunction after iOS 5.1.1 update

    I updated my iPhone 4  to iOS 5.1.1 on Friday, it worked normally for about 24 hours, and now all of a sudden it is completely unusable. If I press the home button absolutely nothing happens. But if I plug it into the charger and then press the home button, the white apple appears, and it boots to the grey screen that you get with a brand new phone. When I then swipe the slider I am asked for a passcode, so I enter the one I used when the phone was working normally. I then get the screen that says to connect to iTunes. Problem is that I'm traveling and so for the moment cannot connect to my iMac at home. (I have a PowerPC G4 laptop with me that can't go beyond OS 10.4 and iTunes 9.1.1.) Can anyone shed any light on this? Is there anything I can do now or do I have to wait until I return home? Or is the phone totally toast or what? I've read some stuff about SIM cards being corrupted with this update. Would a new one restore the whole phone?

    Exact same thing happened to my Iphone 4 on August 4th (366th day of 1 Year Warranty).  When connecting to ITunes, Restore fails and a message pops up in Itunes stating that "There is a problem with your IPhone" and directs you to Customer Support.  I took the phone to  Apple Store, the Geeks there experienced the same problem and were unable to resolve.  They suggested that the phone needed to be replaced at cost of $159.99 eventhough it started to malfunction 1 day after warranty expired.  Endless amount of pleading/arguing failed to sway them into giving me a free replacement.  Phne still not working.  Would changing the SIM help?

  • Problem on Syncing after iOS 7.1.2 update

    My iPhone 4S just updated to iOS 7.1.2 and I intended to add some songs into it. However when I tried to sync, the sync process only lasted for 5 seconds and my songs are not imported into my iPhone. Already restored it and tried again, but to no avail. Is it the flaw in the new iOS or the iTunes issue? Apparently my mother was bored and she went to download a free song from the iTunes, was that also one of the cause for all these? HELP PLEASEEEEEEEE

    check and uncheck or uncheck and recheck "sync only checked songs and videos" setting.
    You should be able to sync music.

  • IPhone 5 battery draining after iOS 6.0.2 update even on standby mode without wifi/ 3G at all.

    My newly bought iPhone 5 was on iOS 6.0.1
    everything worked fine and i had no wifi nor battery issues at all until I upgraded it to iOS 6.0.
    i noticed some battery drainage even when i'm not using my phone at all it still drains 1-2% on standby mode with no wifi nor 3G at all in an hour,
    If i use wifi it'll drain 4-5% in a few minutes time, more serious case when i use 3G, it's literally draining in EVERY SINGLE MINUTE.

    ckuan wrote:
    Jonathan wrote:
    So my iPhone 5 always had the problem of disconnecting from the wifi signal I was on whenever the iPhone is locked.
    Per designed, Wi-Fi will disconnect in sleep mode to save battery.
    If you want Wi-Fi to stay connected even in sleep mode, plugin to a wall power socket.
    No it's not "per design". It's not supposed to disconnect when locked/in sleep mode. The whole concept of having live notifications to work when your phone is locked is the standard for smartphones. Having this feature only accessable when pluging/charging the phone is rediculous and counter-productive. But it's good to know that I'm not the only one who has this issue. I hope all our issues are solved swiftly, good luck to you all

  • Iphone 3GS keeps restarting after ios 4.3.2 update! Help please.`

    So I recently updated my uncles iPhone 3GS from a very old version 3 something to the latest. It randomly restarts within about 5 minutes of using the phone. You could be in a call and it would just shut down. Any help on resolving this issue please?

    Sorry unit was upgraded to iOS 4.3.3. Unit is now out of warranty by 23 days. I would like to think out of courtesy that Apple would replace my iPhone for the inconvenience caused by the upgrade as the phone was working perfect prior to the upgrade.
    Please help Apple!!!

Maybe you are looking for

  • Adobe, please stop running from this issue! (GPU vs CPU anomalies / fades)

    Adobe, I have tried to bring this issue to light many times, and your own users have argued it ad finem, but to no avail! I am TIRED of getting terrible alpha blending (and opacity curve) results with GPU acceleration enabled, vs CPU. In fact, it is

  • Standby database in sync ... ?

    Dear Experts, (Oracle 10g, Windows Server 2003). we have a standby database in maximum performace mode, I want to make sure that both are in sync or not, ihow to find ? and if they are not then what must be done to make them in sync. Thanks&Regards s

  • Sendmail.php

    Hello, I'm trying to do a sendmail.php - I looked at this site for advice - so I pretty much copy & pasted the code from it; http://www.codetricks.com/article.php?cat=phpmysql&id=11 Having followed the instructions, it seems to have worked, i.e. give

  • Msi Neo2 Kingston HyperX PC3200 BH5 Any Good ?

    Hi Guys Anyone using 2x256mb Kingston HyperX Pc3200 Bh5 on the neo2? curious at what fsb/timings u can run. and if 3.1-> V would help. thinking of buying a pair but would be great seeing some results first. thx in advance.

  • Problem to insert using execute immediate

    Have a procedure like this: create or replace procedure proc_set_category( VC_object_id IN number, VC_object IN varchar2, VC_category_id IN varchar2 is sq varchar2(200); BEGIN      sq:='INSERT INTO ' || VC_object ||'_category (' || VC_object || '_id,