My iPhone turns off whenever it goes into standby mode and has to be turned back on to work

My iPhone turns off whenever it goes into standby mode and has to be turned back on to work

That's normal behavior. It turns off automatically in order to preserve the battery. Pushing the On/Off button turns it on immediately. This also requires entering the passcode and prevents the phone from being accessed by anyone but you.

Similar Messages

  • WiFi turns off, too , when going into Airplane Mode

    Hi all,
    not sure if this was the case before OS4 but I have noticed that when connected to Wifi and then switching to air-plane mode , Wifi will turn off as well but works again after turning it back on. (Air-plane mode will also stay turned on)
    Is this a bug or normal behaviour?
    Thanks

    That is how it has always been (well not always, original you couldn't have Wifi and Airplane at same time).
    Process is always turn on Airplane, then you have to manually turn back on WiFi.

  • My iphone 4 only turns on when its plugged into a wall and when it finally turns on it lasts for about a minute then it turns off and while its on the signal says searching, what should i do?

    my iphone 4 only turns on when its plugged into a wall and when it finally turns on it lasts for about a minute then it turns off and while its on the signal says searching, what should i do?

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.      
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. You likely have a bad battery.
    Apple Retail Store - Genius Bar                       
    Apple will exchange your iPod for a refurbished one with a new battery for $79. They do not fix yours.
    Apple - iPod Repair price                       
    A third-party place like the following will replace yur battery for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the battery yourself if you are up to it. A replacement costs about $10
    iPod Touch Repair – iFixit

  • Macbook spontaneously goes into sleep mode and screen off mode

    Hi. My Macbook spontaneously goes into sleep mode and screen off mode with varying time between each instance. It usually goes for a few minutes or even hours without doing it and then will go through periods of fluctuation between the modes. I believe this to have started with a minor orange juice accident rather than it being anything software related.
    Any ideas as to how I might rectify the problem? Thanks very much in advance,
    Danny

    When you say it goes into sleep mode ...do you mean you actually see the white pulsing light?
    It may be that there is an application running (perhaps in the background) that is keeping your book awake. Printer software sometimes does this for example ...try logging out and seeing if it sleeps like that. If it does, then it very well may be a background process running.
    You may find some items in System Preferences/Accounts/Login Items that may be the culprit.

  • I am about to go get my 4th iphone 4s since November!  Up in the left coener where it shows your signal strength, it goes into searching mode and stays there.  Kills my battery.  This one has lasted the longest-I got it December 23.  Any ideas out there?

    I am about to go get my 4th iphone 4s since November!  Up in the left corner where it shows your signal strength, it goes into searching mode and stays there.  Kills my battery.  While in searching, no calls can be made/recieved, no internet, etc. This one has lasted the longest-I got it December 23.  Any ideas out there?

    Both.  The first two, I did use my itunes.  The guy at the apple store said that could be the problem.  The last time they gave me a new phone and SIM card, and the tech said it wouldnt be the itunes.  Just to be safe, I never connected this phone to the itunes until last night-after it started searching- to save everything since I'm sure they will be replacing the phone today.  But hey, thanks for the suggestions.  I'm about at my wits end with Apple!!  Especially since i added a third line to my account just so I could get an iphone back.

  • Monitor goes into sleep mode and will not wake up

    My monitor goes to sleep and will not wake up.  I try powering off and that will not respond.  I have to unplug the workstation and start back up.  I have turn off sleep to never sleep and now it just goes to sleep when Im working. 

    Hello @rosendahl14,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how your monitor goes into sleep mode and will not wake up, and I would be happy to assist you in this matter!
    To rule out any sleep mode issues with the monitor, I am providing you with some steps you can try below:
    Step 1. Unplug the power cord from the back of the monitor and the wall
    Step 2. Hold the power button down for at least one minute
    Step 3. Plug the power cord back into the monitor and then into the wall outlet (not a power bar or surge protector)
    Step 4. Press the Menu button on the monitor
    Step 5. Navigate to the Factory Reset option and select it
    Step 6. Try a different cable connecting your monitor to your computer
    If the above steps did not resolve your issue you can try the monitor on a computer or other device to see if the issue persists. Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assis​t.html
    To further diagnose a possible hibernation issue with your desktop, I recommend following the steps in this document on Troubleshooting sleep and hibernate issues (Windows 7). I also recommend following the steps below to reset your system's power management settings:
    Step 1. Click the Start button
    Step 2. In the search box, type "Command Prompt"
    Step 3. Right-click Command Prompt
    Step 4. Click Run as administrator
    Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter 
    reference: http://superuser.com/questions/669571/windows-8-1-​64-bit-power-schemes-gone
    Please re-post with the results of your troubleshooting, and I look forward to your reply!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • While editing a document,Pages goes into beachball mode,and quit

    While editing a document,Pages goes into beachball mode,and quit.  Cannot retrieve edits

    Is it just one particular document or any document?
    If just one document I'd guess there is some corruption in the document, usually a font or an image.
    If it is all documents, the corruption likely lies in the Pages preferences. Go to HD > Users > (your account) > Library > Preferences, delete the com.apple.iwork.pages.plist file & then restart Pages. In Finder, hold down the Option key while clicking on the Go menu & your user Library will appear about halfway down the list.

  • My macbook pro automatically goes into safe mode and doesn't start. I use mavericks.  what to do? ?

    my macbook pro automatically goes into safe mode and doesn't start. I use mavericks. What to do??

    Can you boot into your Recovery partition (hold down the command and R keys whilst booting)?
    Call back - you'll be able to connect to this forum from Safari whilst in Recovery.
    Clinton

  • My new macbook pro retina randomly goes into standby mode

    My new macbook pro retina randomly goes into standby mode. I have to close the screen and wait a few seconds and re-open it in order for it to come back on.
    Sometimes it immediately goes back into standby mode again after closing and reopening the screen. I have checked the battery level everytime, and it has never been below 40% when this occurs. Is this a Mountain Lion issue?

    Well I fixed my problem.
    I took it into the Apple store. Even without the other two monitors they were able to recreate the problem. One symptom (I had) was that one of the Hot Corners was set to Disable screen saver. If you then put your cursor there, you'd go into screen saver mode. Change the setting to another corner and the problem follows you there.
    The Apple person at the Genius bar logged out as me and back in as test and same problem. He tried some stuff and finally said I needed to wipe the drive and reinstall the OS (Lion). I'd only had the machine for 12 hours and had just migrated my data to it, so I didn't mind doing that. I did it at home.
    Problem solved.
    BUT... then I reinstalled the driver for my EVGA UV Plus 19 (most current drivers) and bingo problem back. Uninstall. Problem gone. I'm now using mini display port to DVI for one monitor and HDMI for the other I think the machine is a bit warmer this way (versus using a USB to the EVGA device) but at least it's not sleeping all the time. Someone might say "it (the heat) is your imagination" or something else. Or someone might say "use the other thunderbolt port for another mini-display port to DVI" but I need that for the LAN... c'est la vie.
    Maybe I'll write to evga and see what they say. Maybe they'll fix their driver and/or Apple will fix it.

  • Wifi goes on and off, backlit keyboard doesn't work and no sound since Lion  upgrade. I can get the wifi back by going into safe mode and re booting(someone suggested on here), but can't let computer die or turn off or have to do it again.

    My Wifi connection goes off if computer dies or shuts off, I can only make it work if I go into safe mode and reboot, it was just that, but now my keyboard doesn't light up like it's supposed to in low or no light and in system preferences it's like it doesn't exist.  Also, the sound doesn't work, I can't turn it up or down, it shows the sound icon grayed out and the anti symbol when I push F11 and F12, also it's like it doesn't exist in system preferences either. I have never had any problems with my MB Pro, I purchased in Feb. 2010. , but I upgraded to Lion last month, I haven't been using my laptop as much since I had an Ipad I given to me, so I think that's why I didn't notice these issues right away. What do I do? HELP!! Do I take it to Apple? I don't have the Apple care warranty, so will it be expensive for them to fix? Can I get my money back for Lion if I restore to Snow Leopard?

    Take it to an Apple store or AASP. How much it will cost will depend on their determination of the problems. To bad you didn't purchase extended AppleCare. No you don't get your money back for purchasing Lion.

  • HT1414 Phone goes into panic mode and shuts off and reboots every once in a while

    So i had my iphone 4s replaced a few months ago and i restored my iphone with my backup from my last iphone i had and i just started noticing my iphone wouldnt respond when i hit the power or home button even tho i know i have it turned on and when i press the home button it reboots or either it will go into panic mode and i have to hold down the Power Button and Home Button till it restarts itself. I dont think my backup files on itunes are corrupted but maybe they are or maybe my phone is malfuctioning. Anyone have this problem with Iphone 4s or 5 or anyone have any advice whats going on or what i should do?

    Hey Fleurdemimi,
    Thanks for the question. I understand you are experiencing issues with your iPhone 4s. Based on the information you have provided, restoring your iPhone in recovery mode may resolve your issue:
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    Thanks,
    Matt M.

  • 24" imac goes into sleep mode and lights on circuit flicker

    Hi -
      I have a 24" imac and have found that when the display goes into sleep mode the lights on the circuit flicker.
      I have searched the web and other users have complained of the same issue with no resolution.  
      Here is a similiar post - https://discussions.apple.com/thread/2606099?start=0&tstart=0.      The resolution is probably you need to get the iMac serviced,  what i'm wondering is what is the problem in the imac that is causing the issue.    Is this a defect?
      Before anyone questions the circuitry in my house here is what I have verified.
      An electrician has come and verified the electric panel is good and all circuit breakers are good.   All circuits in my house are copper, no aluminum.
      I can plug the iMac into any circuit and the problem starts right when the Imac's display goes to sleep.     I have owned the iMac for approximately 5 months now (bought it used) and the problem started about a month ago.
      Assuming this has to be serviced I dread to wonder the price .
      Thanks for anyones help.

    The sleep timeout has nothing to do with disk activity. It's based on user input, although some background processes can pre-empt it. If you don't want the machine to sleep automatically, disable automatic sleep in the Energy Saver preference pane.

  • RBDAPP01 going into SLEEP Mode and Idocs still in 64 status

    Hey all,
          I have a Inbound Idoc interface which is being processed using RBDAPP01 Program. The Issue I am facing is that the job running the rbdapp01 program goes into sleep mode even though there are idocs present in 64 status. I tried to debug the work process using SM66 but it does not open any debugging window although it says debugging started. If I cancel the Job and run it again it processes those Idocs Any input on how one can resolve this issue?
    Thanks.

    Hi Aparna,
    Here is extract from SAP material on running RBDAPP01 transaction and possible reasons for delay in processing. HOpe this can help you.
    To automate the treatment of IDocs, you must run the ABAP program RBDAPP01 (transaction BD20) in job. This program has a very good option for parallel processing which can reduce a lot the time required for treatment. However use it carefully and make sure you set a packetsize high enough to avoid that your SAP system be overwhelm by demands for available dialog tasks (don't forget one dialog task is monopolized per IDocs packed to treat).
    Best Regards,
    Krishna

  • My phone turned off by itself while it was charging and it does not turn on

    Good morning, I have an iPhone 5 iOS 8.2 I believe.
    I connected my phone to the charger and went to sleep as usual and when I woke up it was off dead and since that I can not turn it on. I tried to turn it on several times but it did not work
    please help me with this issue.
    Asmaa AlRawe

    IIt happened with me 2years ago with iPhone 4s running ios6,i thought the phone is dead, try to restart ur phone(even if it looks turned off) by holding power button and home screen button together till apple's logo appear , it worked with me b4,good luck and best regards.

  • I just updated 3 addons and now Firefox goes into background mode and I am not able to reach the Tools/Addons to disable any addons.

    Firefox stays in foreground for maybe 10 secs before going into background. I can't reach FF to do anything with FF.
    I have to use Task Manager to close FF.
    I don't remember which 3 addons were updated, but I was notified of updates when I tried to open FF at about midnight this morning.

    hi there i tried the removal of the sessionstore.js file and and fired up the mozilla firefox up again and still no joy from the windows xp machine all other browsers work fine, its just hanging still, reading the article from the link you sent i can't any issues that i am getting but i did manage to un-install the FF8 again deleted any folders and dowloaded V3.6.24 from here http://www.mozilla.org/en-US/firefox/all-older.html
    then updated from there and all seemed to go well then yet again i got the same issue ,when i open the browser i am unable to type in the search and use the mouse on the File edit etc menus rendering the browser useless so i think its a the update to V8.0 that is causing the issue, when i reinstalled i had no themes no plugins the extensions on the 1st boot ticked the MS .net there was that and java Un-ticked when the browser booted up it was the same hanging for ever . i think i may stick with the older version for now until a fix is available as there is some thing that does not like this new version on that pc... but i hope you can help me to upgrade as its annoying now
    :-)

Maybe you are looking for