My iphone won't shut off the internal microhone when using garageband or amplitube, it used to work fine but then one day changed?

Hi, my iphone used to work fine, when using garageband with an irig it would shut off the internal mic, all of a sudden this is not the case. even without irig plugged i it still uses the internal mic which has never been a roblem? answers anyone?

I have the same issue, my iphone 4 wont connect to one of my macs but will charge, when i connect it to another mac it connects straight away... i restarted and reinstalled and nothing....
Laptop 1
iPhone 4 - Not connecting to iTunes but will charge.
iPhone 4s - Connects and charges.
iPhone 5 - Connects and charges.
Laptop 2
iPhone 4 - Connects and charges.
iPhone 4s - Connects and charges.
iPhone 5 - Connects and charges.

Similar Messages

  • HT1414 Anybody have an ipad that will not power on, for no reason? My ipad always worked fine and then one day it shut down because the battery was low so I plugged it in and it will not power on. Tryed the hard reset option still no power on :(

    Anybody have an ipad that will not power on, for no reason? My ipad always worked fine and then one day it shut down because the battery was low so I plugged it in and it will not power on. Tryed the hard reset option still no power on

    You can try recovery mode to see if you can revive the iPad.
    http://support.apple.com/kb/ht4097
    Have you left the iPad charging for a couple of hours or so to be sure?

  • My iPhone won't come off the Apple logo when turning on.

    Hello and thank you for taking the time to read this post.
    I accidentally left my iPhone 4 outside on the table for a week or so and upon charging the iPhone came on as usual and worked as usual, apart from I had to hold the off button and the home button at the same time for it to turn on but this worked first time however. When the iPhone then died and I charged it again the apple logo appears for a while, then disappears and then re-appears. I've tried holding the home button and the off button at the same time but that doesn't seem to do anything but make the iPhone show the Apple logo again.
    I was just wondering if there is anything I can do to fix this iPhone as I need it dearly or would I need to get a new one completely.
    Thank you. 

    Did it get liquid damaged?
    Look inside the headphone port, you will either be able to see a red or a white dot at the end of it.
    If it is white, then you should be ok from liquid damage.
    Next thing to do is to plug phone into iTunes, then to hold home and power button for 10 seconds, then let go of power but keep hold of home. iTunes should say it has discovered an iPhone in recovery mode and needs to be restored. Restore it and see if that does it. If it doesn't, then yeh, its dead

  • Iphone won't shut off properly, has frozen on spinning wheel screen

    iphone won't shut off properly, has frozen on spinning wheel screen

    Try to reset the phone by holding the sleep and home button until the Apple logo comes back again.
    If this does not help, connect in recovery mode and set it up "as new device", explained here iPhone and iPod touch: Unable to restore and here How to set up your iPhone or iPod touch as a new device

  • My screen wont turn on, and the screen is black. It was working fine, but then it just turned off. The only way it will work is if I close my laptop, and pinch the two screens together

    My screen wont turn on, and the screen is black. It was working fine, but then it just turned off. The only way it will work is if I close my laptop, and pinch the two screens together

    You have a hardware problem and you should take it into a apple store to be looked at and fixed.

  • I have an iPhone 6.  For the first two weeks my bluetooth worked fine but then started having issues.  Now, although it shows that it is connected to Bluetooth, I can't hear any of the calls.  The radio continues to play.  Please help!

    I have an iPhone 6.  For the first two weeks my bluetooth worked fine but then started having issues.  Now, although it shows that it is connected to Bluetooth, I can't hear any of the calls.  The radio continues to play.  Please help!

    Hello there, Srushevics.
    It sounds like you may be having issues with the connectivity of your iPhone with the Bluetooth in your vehicle. The following Knowledge Base article offers up some great steps for troubleshooting that Bluetooth connectivity with your iOS device:
    If you can’t use a Bluetooth accessory or car kit
    To resolve the issue, you'll need to first sign in to iCloud and review your devices:
    Sign in to iCloud on your iOS devices and Macs with OS X Yosemite (available this fall).
    On one of your devices, tap Settings > Bluetooth and look under My Devices. You'll see all devices that are connected to Bluetooth, but make sure that you see your Apple devices that are signed in to iCloud and are using iOS 8 or OS X Yosemite.
    Sign out of your iCloud account from any devices that you don't want to use. To sign out of iCloud on an iOS device, tap Settings > iCloud > Sign Out.
    Then, remove any inactive devices from iCloud:
    Sign in to iCloud.com.
    Select Find My iPhone.
    Select any devices that aren't active anymore.
    Wait for Find My iPhone to stop trying to find the inactive device.
    You should see the option to remove this device from your account. Select it to remove the device.
    After following the steps above, restart the device with the issue. Then try to use it with your Bluetooth accessory.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Hello, please help, my interface is connected to the microphone and when i open Logic 9 it does´t work. But I opened garageband to check and it works fine. I can record voice with any effect... With Logic i see the sound passes in the interface.

    Hello, please help, my interface is connected to the microphone and when i open Logic 9 it does´t work. But I opened garageband to check and it works fine. I can record voice with any effect... With Logic i see the sound passes in the interface but does not arrive in Logic. The Loops works fine and i can hear. Is just the sound to record the voice it does not work. What can i do ??? I used Logic before in the same computer and it worked fine. Thank you so much, I´m a begginer recording myself.

    Make sure you go into preferences in Logic and set the audio input to be your interface and the audio output to be either built in output or the interface, if that is hooked up to something else. It sounds like Garageband has the audio interface set as the input but not Logic.
    Also make sure you close all other applications except Logic to ensure it is not running in slave mode...

  • Please can anyone help with the continuing password rejection problem with email.Ipad and other systems work fine but despite reloading my password on imac it bounces back.Apple store has been visited and I have tried everything they suggest.

    Please can anyone help with the continuing password rejection problem with email on my imac.My Ipad and other systems work fine but despite reloading my password on imac it bounces back.Apple store has been visited and I have tried everything they suggest.

    I use free Yahoo mail webMail access because folders I created in webmail access doesn't get set up in Apple Mail. While I was searching for post about password and keychain issues, I stumbled on several threads that complain about Mail folder issues, so I'm holding off on Apple Mail.
    On the password and keychain issue that your post is all about.  I've been using login keychain to save and automatical fill my login screens for a year or so successfully, with Safari and Chrome. Automatic form fill also works for Facebook login. Unfortunately, about 4 to 6 months ago, automatic password form fill stopped working with Yahoo webmail, while still worked for GMail (Safari and Chrome). I tried deleting the password entry for my two Yahoo email accounts to start fresh, but neither Safari not Chrome will even ask me if I want to save the password. I was so frustrated that I eventually installed the keypassX 0.43 (password manager) that is quite primitive sompare to OS X's keychain (when it works). Probably no surprise to you yet.
    The surprise, to me at least, is that, for whatever reason, password auto form-fill from keychain started working again for Yahoo webmail login on Safari about 5-7 days ago. Still doesn't work on Chrome!
    Two tips I can share, at least with webmail access:
    1. Password is save only for one of my yahoo mail accounts. When I login in with my other yahoo account, I get no prompt to save the password, and form fill doesn't work when I try to log in a second time with my other Yahoo mail account.
    2. On inspection of my login keychain, I see a webform password item saved for my Yahoo account that works with keychain. The name of the password is: login.yahoo.com(MyAccountName1#). When I open the password item and look in the Access Control tab, I see Safari and Chome are listed as allowed to access this password item..
         I also an "Internet password" item with a name of just login.yahoo.com. When I open the the password item, it looks just like the password item created for MyAccountName#1, but the MyAccountName#2 is listed in the Account field. Inside the Access Control tab, no apps are listed in access permission. I added Safari and Chrome to the lists of allowed app, saved the password item.
    Now when I bring up the Yahoo login page(by bookmark) on Safari, form fill fills in MyAccountname#1 for name and the proper password and I can login in. When I change the name to MyAccountName#2, the correct password is retrieved and I can log in! Alas, it still doesn't work on Chrome.
    BTW, I changed the password item type from "Internet password" to "Web Form password" and saw no difference! I also edited the name to be "login.yahoo.com (MyAccountName#2)" to look like the web form password item that works, but it has no effect either.
    From my experimentation, here's my observation:
    1. A Web Form password item is created for the first account name(MyAccountName#1) for login.yahoo.com and typed as Web Form password. When I log in using MyAccountName#2, an Internet Password is created, but no applications are listed as allowed to access the password item, even when the password item was created after just logged in and logged out to yahoo with the account name and password for MyAccountName#2.
    2. Manually adding Safari as an app that is allowed to use the password item works. Doesn't work with Chrome!
    The version of Safari I'm using is Version 5.1.7 (6534.57.2). My installed version of Chrome is Version 21.0.1180.79 beta.

  • Big fan noise problem: the rear fan won't shut off, the BIOS won't update, systemupdate locks up

    I received new ThinkStaion (oh boy, lots of memory and CPU speed, yay!)
    I unfortunately left the originally installed Vista OS on there.  Very much regretting that as I believe it contributes to the following problems (BIOS).
    So the original problem was that after just a month of using my new ThinkStation, the System Board died, and it had to be replaced. Honestly, all I did was choose the sleep or hibernate option in Vista to shut down.  Afterwards,poof! didn't even get the proper Power lights on the system.  I diagnosed this with the online docs and then sat for a few hours on our tech support line doing all the same things to re-diagnose it.  
    So after the replacement, the rear fan will not shut off. Jet engine noise all day. I went into the system settings and selected "Quiet" for the Fan settings but that did not help.
    Research on this forum resulted in the possibility of a BIOS update fixing the problem.  Comparison to my co-workers systems which arrived at the same time shows this BIOS is woefully out of date, so even if it does not fix the fan issue I want to update it.  However, everything I've tried to do is failing for one reason or another. 
    (The fan issue does need resolution since in one week I will end up sharing an office (first time in many years, thanks IBM for nothing!) so since I don't want us both to have to wear noise cancelling headsets, I'd like to fix this without having to just pull the @#$@ power to the fan. Grrrr. )
    I downloaded what I felt were the appropriate Lenovo apps to update both the BIOS and the serial number but none seem to work properly from the command line in Vista.  One of the two (can't recall which) asks me to reboot and it never actually shuts down. Eternal "Shutting Down" message. Ga!  The other throws some gosh awful
    systemupdate le
    http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-69701
    eternal reboot
    BIOSD attempt:" 2xjy26usa
    http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-69701
    error 1275 no admin priv - I AM the administrator account, there is no other acct to use!
    Then I decided Vista might be the problem and found sites recommending flashing the BIOS from a bootable USB.  So I started down that path and after burning the wrong version, finally geting the AIK Vista tools installed and to the point of trying to make the USB bootable, it won't allow me to put the OS boot on it.  Ah, for the days when a simple "sys a:" took care of that.
    So, after reformatting the USB and pounding my head in the wall, keyboard, etc. I am at my wit's end.  What to do.  I just want the fan noise to go away.
    This does seem to duplicate other forum messages but I can't get anywhere on this.  Help!
    Solved!
    Go to Solution.

    FYI to all the helpful folks here (and any looking to shut their jet engine off as well): Flashing the BIOS did the trick.
    First I had to find a website with DOS OS files and put those on the USB instead of Vista.  Oldie but a goodie, but at least it booted! No other versions would.
    I had been intending to use the WinPhlash utility that Lenovo supplied with the BIOS update but since I was booting from DOS that was useless. However, I found a DOS version of it and used that instead. Boom baby!  Flashed and rebooted. 
    It did take two boots to get it back to normal (first one gave very alarming messages about no operating system being found but I think it was just a remnant of the reboot that was triggered from the DOS session).  A second boot returned life to normal and blissful silence from the server.  And I was finally able to get the model and serial number back in there to get rid of the bootup message it throws for that too.
    Ahhhhhhh. 
    Thanks to all for the hints - I believe I had gotten the idea of flashing the BIOS to solve this from some other thread I found here.  This is a very nice forum to have bookmarked.  

  • My Iphone 5S is shutting off by itself and when it fades off, the sound goes off too!! Has this got to do with the new ios rel.7.0.6 update?

    I have upgraded to my Iphone just recently and everything was working fine until I donwloaded to ios7.0.6 and now the phone would shut down for some reason....the music or live radio would also also fades off as the power shut down. Can anyone explains this? Or better still a solution.........

    Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)
    If this doesn't change anything, backup and restore your software via iTunes. If the problem continues, restore as a NEW device. If this solves it, that means there is some corruption in your backup file, or maybe it's one of your apps causing the trouble. If the problem is still there, you should take it to the Genius Bar at an Apple Store for evaluation.

  • My MBP was working fine, but then the display just shut off... What should I try?

    I was using my MacBook Pro 2011 13', when the display suddenly shut off. I thought at first that the computer shut down, but after a hard reset, the computer is on (keys lighting up, fan noises, heartbeat light on) but the display is completely black. I no longer have apple coverage. Does anyone have a recommendation of things I could try before taking it in?

    Try resetting the SMC.
    Barry

  • My iphone 5 was dropped in the toilet water yesterday and i pulled it out and left it alone but then after it was working perfectly and now it wont turn on .. what do i do ??!

    I dropped my iphone 5 in the toilet at the park yesterday and it was still working so i turned it off and left it in my purse but then when i got home i put it to charge and it was working perfectly and then i used it till it as 1% i put it to charge again then ichecked on it in an hour and it wouldnt turn on no matter if i plugged it in . .then my friend tld me to leave it in the rice so i did overnight and now today it still didnt turn .. what do ido?? please help ?

    Replace it - it is almost certainly ruined beyond recovery at this point.  You had a slim chance at best - had you left it turned off, never tried to charge it, and placed it in uncooked rice for 5-7 days it might have worked (although honestly, not likely).
    For future reference, water and energized electrical circuits will mean disaster as the electronics will short out.  Never power on a wet device, and never connect it to an external power source (if it has a removable battery, immediately disconnect and remove the battery as well).
    Now, it is has to have been shorted out beyond any hope of recovery.
    You can get an out of warranty replacement from Apple for $269.00 USD
    http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipho ne

  • HT201210 I upgraded from iPhone 3G to 4S a few days ago. I choose the option to restore from my last 3G backup. It worked fine but I just realized that I do not have the new apps which come with the 4S. What should I do? Thanks for any help. Léo

    I upgraded from iPhone 3G to 4S a few days ago. When setting up the new 4S, I choose to restore my last 3G backup. It started by updating the OS to version 5.1 (9B179) then restored my apps and setting. Everything went well except that I realized I do not have the new apps which come with the 4S, like FaceTime, HD video and Siri.
    What should I do to correct this?
    Thank you in advance for any help on this.

    Ah, FaceTime is not an app, either. It's accessed by tapping the FaceTime button when you are in the contacts app and have selected a contact. This can also be done from the Phone app under the Contacts tab, or during a call, you can switch to FaceTime.
    Let me know what other apps/features you are missing.

  • I'm using Firefox version 3.6 on my '02 Mac G4. When I installed it, it worked fine, But then all of a sudden the "save" and "save as" windows stopped coming up at all when I selected "save" anywhere in Firefox. What happened and how do I fix it?

    I downloaded and installed Firefox on my '02 Mac G4. It worked great. Now I have version 3.6. But my weird problem is one day when I ran it, the "save" and "save as" windows stopped popping up at all. I'd left click a picture and select "save as" and nothing would happen. I'd go to the menu and select "save" and still no window would pop up. It would just act as if nothing had been clicked. No loading icon or anything and no "save as" window. I've never been able to get it to work. The volunteer in the live support chat typed "That IS weird.." I tried his suggestion but it did nothing. I may have deleted the plist preferences file in the preferences library folder to get it started again after a freeze up threw it out of whack but I've never had this happen before.And i've tried doing that again to see if that would restore it. But the plist always regenerates itself and the "save as " window still never appears when I run Firefox. The "save" window works just fine in every other program on my Mac, but not in Firefox. Weird..

    Leliforever, cheek you list of installed add-ons, the Ask toolbar can be installed without the users knowledge.
    For checking other extensions that may cause this, follow the procedure in this link - https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

  • Hi, I have a problem with my Epson Stylus NX420. I had it connected and it worked fine but then all of a sudden it just stopped. It said it was offline, but it wasn't. So I tried to reinstall the printer, so i deleted it and clicked the   button to add

    Hi, I have a problem with my Epson Stylus NX420. I had it connected to my computer, and it worked fine. But I preformed a remodel and before the printer was connected to a windows desktop, and now it is not. I don't know if this could the be the cause of the problem. But I tried to print something and it showed me the printer as offline, but it wasn't. Thus to try to fix this, as I have done before I deleted the printer and tried to add it again. But as I went to add it, the printer was not there. I have searched the internet for an answer and I have found nothing. I do not understand why this has happened, nor how to fix it. Please help me.

    Because you had the printer connected to Windows, the print queue on your Mac was for this connection. With you moving the printer away from the Windows computer, the print queue on the Mac will no longer work and will show offline. So for the new connection of the printer you have to create a new print queue.
    Now the question is; how is the printer connected to the Mac. If it is connected by USB to the Mac then it should appear in the Default Add Printer view. If it is connected to the Mac via some other method, then could you reply with how it is connected.
    If it is connected to the Mac by USB then the most likely cause for the printer not appearing in the Default Add Printer view is thenUSB printer cable. So try disconnecting it and reconnecting it or even try another USB printer cable.

Maybe you are looking for