My iphone won't start at all and slowly started to fade out
my iphone won't charge from Dec 31 midnight. well first it was freezing, and i lock it then i plug the charger. but it doesn't turn on until morning - right now actually. i already restore it and it was working but it freeze again! i reboot it over and over but black dots started to show up and the screen started to fade out. according to my experience, the screen were burned. is it means that i should go to the store for fixing it or i should get a new phone? HELP!
Did you try booting into your Recovery partition? Hold down the command and R keys whilst booting and if you can get to your Recovery partition use Disk Utility to verify your disk and, if needed, repair the disk.
If it can't be repaired, then it's likely dying.
Clinton
Similar Messages
-
my iphone 4s shuts itself off all the time. starts normal and then shut it off and start all over again, what is wrong?
Your iPHone is designed by intention to shut off when there is a reason for the softwarer to believe that danger is immenent to the hardware. This can occurr if the software is running applications that have been corrupted due to all types of different scenarios. My best advice to you would be to restore your device back to default manufactures settings and do NOT restore the current backup of the IOS program currently running.
If this corrects the problem with your device intermittently restarting you will then know you have had applications there were corrupted on your device. Once you are convinced there are no issues with the hardware of your device you then are free to begin downloading software apps that were earlier on the device.
Good luck. -
My iPhone won't work without wifi and I can't receive or send iMessage unless I have wifi or 3G can't use Instagram, Twitter or anything to do with internet or messaging, how do i fix it?
For anyone else wondering how to fix this, all I did was turn my iPhone off and then turn it back on.
-
So the left side of my iPhone isn't working at all and I even tried turning it off for 5 minutes about 10 million times but nothing is working. Any suggestions on what to do I need help like ASAP!?
Have you performed a reset? Tap and hold the Home button and the On/Off button for approximately 10-15 seconds, until the Apple logo appears. Release both buttons and await restart.
-
My iPad air won't change at all, and I don't know if it's the port or charger cable it is charging normally but it just won't charge. I have had a new port put in before after a charger getting stuck in there but it worked fine after and now it's not working at all! I don't know if maybe it's the charger getting old but I have spent far too much money on this iPad then I should have as it's one problem after another witch is causing me lots of stress.
Try giving your iPad a reset. Hold down the sleep and home keys for about 20 seconds. When you see the silver apple, let go and let it reboot and try again.
How are you charging it? its's best charged plugged into the wall not via USB. So if you're trying via USB, try using the supplied power block plugged into the wall. -
InDesign won't open at all and no error report is given, I can't even open up my existing files. Any suggestions?
i have the 30 day trial because I'm doing a project for a college class. Im running the most updated version of windows
-
Iphone was dead when i woke up, wont start or charge and suddenly started after 10 minutes.
Iphone was dead when i woke up, wont start or charge and suddenly started after 10 minutes.
Try a reset. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. The phone should restart. This can take up to 20 seconds.
-
Macbook Pro 2014
13-inch
Intel i5
8GB RAM
128GB flash SSD,
Integrated Graphics
iPhoto library is on external HDD
I was in a slideshow, with around 1,911 photos in it. About halfway through, my Macbook ran out of battery. Now when I restarted and charged the Macbook and reopened iPhoto, the slideshow won't advance through photos, and I can't figure out any reason why it would do this.
I thought it may be corrupted, so I deleted and reinstalled iPhoto library, iPhoto itself, and disconnected and reconnected my external HDD.
This didn't work, the photos still won't advance.
I don't know any reason why this would be happening, and there is ample space on my internal drive.
I'm happy to provide more information if needed!
Many Thanks,
JamesMake a few tests, James, to narrow down the problem and find out, if the slideshow is corrupted, your iPhoto Library, or settings in your account.
To test, if only your slideshow has a problem, create a new slideshow, just for testing. Just use "File > New Slideshow" and add a few photos. Does this slideshow play correctly?
If the test slideshow does not play either, create a new iPhoto Library. Use the File menu in iPhoto: File > Switch to library > Create New. Import a few photos and create a slideshow. Does it play?
If even a new library does not solve the problem, test in a different user account (see this document: Isolating an issue by using another user account - Apple Support):
This process involves creating a new user account, logging in to it, and testing for the issue.
Create a new standard or admin user account in Users & Groups preferences.
Use these instructions for OS X Mavericks.
See these instructions for OS X Mountain Lion.
See this video, or these instructions for OS X Lion.
Optional: If you have any specific files you wish to test with, copy (don't move) those items to the /Users/Shared folder in the Finder.
Log out of your current user account by choosing Log Out from the Apple () menu.
Log in with the new account you created.
Attempt to reproduce the issue you were seeing in your regular user account.
After you have completed testing, log out of the test account by choosing Log Out from the Apple () menu.
Log in as your regular account.
After you have completed all testing with the test user account, you may want to delete it. You can delete an account in the Users & Groups pane of System Preferences.
Note: Prior to deleting a test account, make sure you are completely done with it. If you have files in the Guest User you wish to keep, you should copy them to the /Users/Shared folder .
If you should find, that slideshows only play in a new user account, post back. -
I just bought an iMac, while setting it up I was prompted to update the OS software. I tried to update it. It won't complete the update, and says "Error- requested timed out. (102) what does that mean? how do I fix it?
If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Select "/var/log/install.log" from the file list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar. Then select the messages from the last installation or update attempt, starting from the time when you initiated it. If you're not sure when that was, start over and note the time. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting. -
My iPhone is stuck in recovery mode and I've been freaked out ever since what do i do?
My iPhone is stuck in recovery mode and I've bee freaked out ever since what do i do?
Follow the 3R's- if a restart does not solve your problem proceed
User troubleshooting is:
1.restart, ie power off/on,
2. reset http://support.apple.com/kb/HT1430,
3. restore from backup, restore as new device. http://support.apple.com/kb/HT1414 -
My iPhone won't turn on all the way. It just has the apple and white background
I've tried pressing the top button and home button but still doesn't work
Hello Evelyn,
Thank you for providing the details of the issue you are experiencing with your iPhone. It is definitely inconvenient and frustrating when you are not able to access your iPhone.
I recommend following steps 4-6 below for an issue like this:
If a single application is not responding or stops responding when it opens, you can force it to close.
If the device is unresponsive or if certain controls aren't working as expected, restart your device.
If the device remains unresponsive or does not turn on (or power on),reset your device.
If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
Let charge for at least twenty minutes, then see if it starts normally.
If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
If the screen displays a red battery icon, continue charging the device until the battery is fully charged.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
You can find the full article here:
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
If you get to step 5, I recommend backing up your iPhone before performing the restore:
iOS: How to back up and restore your content
http://support.apple.com/kb/HT1766
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I was having trouble purchasing candy crush updates (for no apparent reason, as it has been fine previously). I thought perhpas I needed to download some new software and promptly started the IOS 6 update. It installed and then asked me to complete the final few steps by signing in with my apple id. When I try to do that it says "it cannot connect to the server". I have tried turing it off and on and over riding it, but it won't let me do anything at all now on my ipad mini.
Can anyone help? I literally can't function!!!!You can't override it no matter what you do. The device has to connect to the server to complete the iOS update. You could try rebooting the iPad and see if that lets you connect to the server after it starts up.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If that will not work, you can try connecting to iTunes on your computer and see if the activation will complete. Sometimes when thes activation issues arise, you end up having to restore the device again, but first things first. Reboot and see what happens. -
Laptop won't power up. lights and fan starts then quits.
HP Compaq MX 9420. Refuses to power up. Lights and fan starts, but then cuts off before boot up process begins. Won't let me do "Hard Reset". What do I do?
Hi JediMaster47,
Welcome to the HP Forums!
I would like to take a moment and thank you for using the forum, it is a great place to find answers. For you to have the best experience in the HP forum, I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I grasp that the notebook powers up and you hear the fan and see lights, but it does not boot into Windows. Here is a link to Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot to assist you.
If this has not helped, I suggest calling HP support for assistance.
Please call HP technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. HP Technical Support Sitemap
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping! -
Videos from my iPhone won't upload to YouTube? Just started happening
Videos on my iPhone won't be accepted by YouTube or FlickR. I get messages saying that there is something wrong with the file. I haven't done anything differently than before. What's going on?
Good question for YouTube and FlickR. What does YouTube and FlickR technical support have to say about this since this?
-
Driver for SQL server with wlserver can't start at all and "no suitable driver" and
Hi all,
After I download the jDriver for Ms sql 2000 server, I set the classpath as document
told, I test it using the utils.dbping it works fine. But when I try to use it
with the weblogic server 6.1 I have the problem as following:
I included the jDriver classes in the classpath of the startWeblogic.cmd as
set CLASSPATH=.;.\lib\weblogic_sp.jar;.\lib\weblogic.jar;C:\weblogic\mssqlserver4v70\classes
saved the startWeblogic.cmd file Then I start the wls with startWeblogic.cmd(the
new classpath). It starts fine Then I setup the connection sql pool using the
weblogic.jdbc.mssqlserver4.Driver It says "No suitable driver"
I found that in the weblogic.jar(shipped with the weblogic 6.1) and in the jDriver
classes, there are two files which have the same name is weblogic.jdbc.mssqlserver4.Driver.
Because in the classpath .\lib\weblogic.jar comes first so weblogic server takes
weblogic.jdbc.mssqlserver4.Driver of the weblogic.jar rather than in the jDriver
classes directory. So I thought the matter of changing the order in the classpath
(.\lib\weblogic_sp.jar;C:\weblogic\mssqlserver4v70\classes;.\lib\weblogic.jar")
will solve the problem, but when I changed the oder in the classpath the weblogic
server did not start AT ALL with the following errror.
------------------Begin error----------------------------
C:\bea\wlserver6.1>"C:\bea\jdk131\bin\java" -hotspot -ms64m -mx64m -classpath
". ;.\lib\weblogic_sp.jar;C:\weblogic\mssqlserver4v70\classes;.\lib\weblogic.jar"
-Dweblogic.Domain=mydomain -Dweblogic.Name=myserver -Dbea.home="C:\\bea" -Dweblogic.management.password=
-Dweblogic.ProductionModeEnabled=true -Djava.security.policy="C:\bea\wlserver6.
1/lib/weblogic.policy" weblogic.Server ***************************************************************************
The WebLogic Server did not start up properly. Exception raised: java.lang.NoSuchMethodError
at weblogic.Home.getFileSource(Home.java:66) at weblogic.Home.<init>(Home.java:29)
at weblogic.Home.getInstance(Home.java:81) at weblogic.Home.getPath(Home.java:89)
at weblogic.security.internal.ServerAuthenticate.main(ServerAuthenticate .java:77)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:200) at weblogic.Server.main(Server.java:35)
Reason: Fatal initialization exception ***************************************************************************
C:\bea\wlserver6.1>goto finish
------------------End error----------------------------
I wonder how can I use the jDriver with weblogic server?
Do you have any idea what I have done wrong or how to get around with this problem?
Please help
Thanks in advanceTom wrote:
Thank you very much, Joe and Laurent
It works now. You save my life :);-)
Joseph Weinstein <[email protected]> wrote:
tom wrote:
Hi Joe, Thanks for your fast reply.No problem. They pay me to be hear on weekdays ;-)
So what you tell me the driver for MSSQL 2000 is in the weblogic.jaris that
correct.yes.
And my connection pool definition:
<JDBCConnectionPool DriverName="weblogic.jdbc.mssqlserver4.Driver"
MaxCapacity="5" Name="mySQLPool"
Properties="user=sa;db=ejb20;hostname=XXX;password=realpassword;appname=ejb20Phone;server=ivm_server:1433"
Targets="" URL="jdbc:weblogic:mySqlPool"/>I see the problem. The URL is broken. It should be the URL that the particular
driver wants, eg:
jdbc:weblogic:mssqlserver4:ivm_server
Then set the pool's Properties to have the user, password, appname, and
db. (no server needed, it's in the URL, and 1433
is default)
thanks,
Joe
I have the port as doc suggest 1433 but it would not help me.
Please help
Thanks Joe
Joseph Weinstein <[email protected]> wrote:
Hi. Our ms driver is already in the plain 6.1 jar file, so there is
no
need for the additional
driver download or classes in the server path. Dbping should workwith
just the server
weblogic.jar etc in your classpath. What is the error you got originally
trying to use
the MS driver with/in weblogic? Show me your pool definition. That's
probably where the
problem will be...
Joe
tom wrote:
Hi all,
After I download the jDriver for Ms sql 2000 server, I set the classpathas document
told, I test it using the utils.dbping it works fine. But when I
try
to use it
with the weblogic server 6.1 I have the problem as following:
I included the jDriver classes in the classpath of the startWeblogic.cmdas
set CLASSPATH=.;.\lib\weblogic_sp.jar;.\lib\weblogic.jar;C:\weblogic\mssqlserver4v70\classes
saved the startWeblogic.cmd file Then I start the wls with startWeblogic.cmd(the
new classpath). It starts fine Then I setup the connection sql poolusing the
weblogic.jdbc.mssqlserver4.Driver It says "No suitable driver"
I found that in the weblogic.jar(shipped with the weblogic 6.1)
and
in the jDriver
classes, there are two files which have the same name is weblogic.jdbc.mssqlserver4.Driver.
Because in the classpath .\lib\weblogic.jar comes first so weblogicserver takes
weblogic.jdbc.mssqlserver4.Driver of the weblogic.jar rather than
in
the jDriver
classes directory. So I thought the matter of changing the order
in
the classpath
(.\lib\weblogic_sp.jar;C:\weblogic\mssqlserver4v70\classes;.\lib\weblogic.jar")
will solve the problem, but when I changed the oder in the classpaththe weblogic
server did not start AT ALL with the following errror.
------------------Begin error----------------------------
C:\bea\wlserver6.1>"C:\bea\jdk131\bin\java" -hotspot -ms64m -mx64m-classpath
". ;.\lib\weblogic_sp.jar;C:\weblogic\mssqlserver4v70\classes;.\lib\weblogic.jar"
-Dweblogic.Domain=mydomain -Dweblogic.Name=myserver -Dbea.home="C:\\bea"-Dweblogic.management.password=
-Dweblogic.ProductionModeEnabled=true -Djava.security.policy="C:\bea\wlserver6.
1/lib/weblogic.policy" weblogic.Server ***************************************************************************
The WebLogic Server did not start up properly. Exception raised:
java.lang.NoSuchMethodError
at weblogic.Home.getFileSource(Home.java:66) at weblogic.Home.<init>(Home.java:29)
at weblogic.Home.getInstance(Home.java:81) at weblogic.Home.getPath(Home.java:89)
at weblogic.security.internal.ServerAuthenticate.main(ServerAuthenticate.java:77)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:200) at weblogic.Server.main(Server.java:35)
Reason: Fatal initialization exception ***************************************************************************
C:\bea\wlserver6.1>goto finish
------------------End error----------------------------
I wonder how can I use the jDriver with weblogic server?
Do you have any idea what I have done wrong or how to get around
with
this problem?
Please help
Thanks in advance
Maybe you are looking for
-
Hi! I have an iPhone 4S with iOS 6.1.3 and I have iTunes 11.1.3.8. on my Windows 8. Now I can't sync my iPhone, because the device is not recognised by iTunes. Somebody have any idea why, or what can I do (except refresh the iPhone software) ?
-
On iCal,how to change the travel time mode from car to foot?
on iCal (Mavericks), how to change the traveltime mode before an event ? i only have the "time" choice with "5 min, 15 min, 30 min, 1 hour, 2 hours". I would like to choose "foot/walking" , "car" or "Train/bus".
-
How do I turn off Auto Play for Audible Downloads?
Ok so this is ticking me off....How do I turn off the Auto Play when downloading Auduible books. It downloads to my download folder and then just startes playing in iTunes. This annoys the heck out of me and I really want it to stop doing it. Es[e
-
Add new contact person in contact management
Hi All, I have been created email in contact management(SRM). in Tab "General", Contact person field, i cannot select new item/New contact person from combobox. I have read at HELP file,then i found to add new contact person in contact management, go
-
OSX Mavericks Keeps Restarting at Random Times When Connected with External Monitors
Starting today, my MacBook Pro started crashing with the below panic report. It appears to only happen when I connect external monitors to the Thunderbolt port. I've been using multiple monitors for the last 6 months without issue. Thanks in advance.