My ipod disabled itself for 23 million minutes. How can I fix it if I don't have itunes on my computer?
My ipod disabled itself for 23 million minutes. How can I fix it if I don't have itunes on my computer?
A computer with iTunes is not required
If you have Find My iPhone enabled, you can use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
You need the iPod and iPad conencted to the interned and FindMyiPod turned on on the iPod an the iPad need to have the FindMyiPhone app installed. That now requires iOS 7 on the device.
You can also wipe by on a computer/s browser, going to icloud.com>FindMyiPhone
Similar Messages
-
I am a professor and frequently need to open pdfs of academic journal articles from electronic databases. Within the last two or three weeks, when I try to do this using Firefox, only the first page of the pdf displays and the rest are blank. In addition, a bar appears across the top with the message "This pdf file may not display properly." So I have had to switch to Internet Explorer to open the files and do my research. What is going on and how can I fix it so I can open pdf files from the Web in Firefox and have them display properly?
My question is simple - why would you put an application in production that has a lot of bugs? To replace a good and steady Adobe product? My customers will believe that I put a pathetic fallible form online. They are not sophisticated on computers so I just tell them to use IE. Ugh
I must agree with pgwebgirl! -
Someone played with my ipod trying to guess my pass word and locked it up for 21,684,750 minutes how can I fix this so that I can enter my pass code in
Hi,
You will have to place your iPod in Recovery Mode and restore it via iTunes: http://support.apple.com/kb/HT1808.
Hope this helps!
---likeabird--- -
Whenever I go to preview a song in itunes, the song with play out for about 10 seconds and then stop. Why isn't the song previews working? How can I fix this? I tried updating my itunes and it didn't work. I use windows 7. Thanks!
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
My computer has a white screen at start up and sits for hours. How can I fix my computer?
My computer has a white screen at start up and sits for hours. How can I fix my computer?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My iPod touch is disabled due to too many password attempts, I don't have iTunes on my computer what shall I do to get my iPod to work?
If You Are Locked Out Or Have Forgotten Your Passcode or Just Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. iOS- Understanding passcodes
If you have forgotten your Restrictions code, then follow the instructions
below but DO NOT restore any previous backup. If you do then you will
simply be restoring the old Restrictions code you have forgotten. This
same warning applies if you need to restore a clean system.
A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
1. Verify that you are using the latest version of iTunes before attempting to update.
2. Connect your device to your computer.
3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
4. Select the Summary tab.
5. Select the Restore option.
6. When prompted to back up your settings before restoring, select the Back Up
option (see in the image below). If you have just backed up the device, it is not
necessary to create another.
7. Select the Restore option when iTunes prompts you (as long as you've backed up,
you should not have to worry about restoring your iOS device).
8. When the restore process has completed, the device restarts and displays the Apple
logo while starting up:
After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
iOS, keep your device connected until the "Connect to iTunes" screen goes away or
you see "iPhone is activated."
9. The final step is to restore your device from a previous backup. If you do not have a
backup to restore, then restore as New.
If you are restoring to fix a forgotten Restrictions Code or as a New device, then skip Step 9 and restore as New. -
My iPad 2 shows I have 7 apps that need to be updated and when I go into my App Store it won't pull up anything for my updates how can I fix this????
It seems Apple is having some issues at their end. There have been hundreds of posts on the forum with the same problem.
-
I'm installing windows 7 64-bit on my imac which I've done before but I get a message that the partition is GPT even after I format the bootcamp partition. I just upgraded my hard drive to a 3tb and I'm allocating 1tb for windows. How can I fix this?
No easy fix for a few reasons:
1) Bootcamp requires a hybrid MBR for the partition table. That is: both an MBR and a GPT partition table at the same time with the GPT one having all partitions and the MBR one having only the ones that are relevant, but at most 4 of them (including the protective partition and the Macintosh HD one). Which leads us to:
2) The MBR part of the hybrid partition table cannot work with 3TB hard drives. MBR is limited to 2TB.
I am working on a small EFI app that can boot Windows in EFI mode on a Mac and that would mean that you can go GPT only on your system. The progress of the app is slow due to the nature of EFI and for now requires that you do an unattended Windows install with slipstreamed graphics drivers, but we are adding VGA loading on top of EFI quite soon after the rest of the app stabilises. The status of the app is documented at:
Win7 x64 booting natively via EFI (no bios emulation)
Windows does actually successfully boot in EFI mode on most Macs (anything with a 64bit EFI should work), but does not have graphics support even if you load the driver due to the VGA pci registers not being set by the firmware. Furthermore, in Setup and Safe Mode, Windows uses VGA instead of GOP which is a failure by design since VGA is a BIOS standard and not really compatible without hacks with EFI. Other EFI implementations also add VGA compatibility at a high cost to the firmware complexity for the VGA cards available on the market that don't actually contain anything in their ROM except the VGA BIOS.
My recomendations:
1) Install on a second smaller hard-drive; or
2) Wait for the EFI app to come out officially and use that to boot Windows Vista SP1 x64 and Windows 7 x64 (RTM and SP1) in the native EFI mode.
3) Wait for Windows 8 which supports VGA-less booting acording to the AMD presentation at UEFI Plugfest. -
my iphone automatically goes to landscape mode.. i can't view the songs in the ipod app coz of this. How can I fix this?
I am having the same problem with a new phone. Is yours new? I was planning to take this one back to the store where I purchased it. I updated itunes and phone software, didn't help, so I'm thinking it's a hardware problem.
-
When i go to Settings- Store, i don't have an "automatic download" for music. How can i fix this?
When i go to Settings->Store, i don't have an "automatic download" for music. How can i fix this?
Not all features of automatic downloads are available in all countries. See this article for a list of countries that shows what content is available.
http://support.apple.com/kb/ts3599 -
Mountain Lion disabled my internal superdrive. How can I fix it?
Mountain Lion disabled my internal superdrive. How can I fix it?
What do you mean by "disabled"?
-
I tried to download a tv show off iTunes on my iPad and it keeps saying I can't download it at this time. But I've paid for it already, how can I fix it?
Try to sign out of iTunes and sign back in, that usually fixes authentication problems.
-
Preferences are missing for Time Machine,how can I fix this?
Preferences are missing from Time Machine,how can I fix this?
Please don't SHOUT!
We're all users here and you'll get more help if you give us some coherrent information.
Firstly, do you have an external Hard Drive connected to use for your Time Machine backup?
Secondly "stacks" is not a programme; it's one method of presenting folder icons in the dock, and is accessed from the 'view options' choice which appears if you click on the folder. Right-clicking the folder will go straight to the options menu. -
I want to cancel my monthly subscription, there aren't any "Cancel plan" button or link for me. How can i cancel my plan. Don't send me the "help" page, i have received much useless advice from adobe. Just help me cancel my PLAN! THANK YOU.
Return, cancel, or exchange an Adobe order
or contact adobe support, http://helpx.adobe.com/x-productkb/global/service-ccm.html -
Some text replies only show up on my MacBook Air and not to my iPhone for some contacts how can I fix this?
Click once on the sleep/wake button to ignore the caller and the call will eventually
go to voicemail. Click twice to send the caller directly to email.
Maybe you are looking for
-
The MainStage 3 Audio preferences window will not find the Aggregate Device input. I have both an Apogee Jam and a MOTU Mike Ultralight in USB ports. The Audio aggregator finds them and treats them as one device. The Aggregate Device does not show
-
Error trying to send email -- IOException while sending message
Email is successful when: I run my application through JDeveloper or when I use a classpath, but if I try to execute app via a jar file, i get the following error message: IOException while sending message. The jar file does include mail.jar and acti
-
Adobe v9 on W7 and office 2007. cannot create PDF from MS word using Adobe. But can from Excel, PPT
Adobe v9 on W7 and office 2007. cannot create PDF from MS word using Adobe. But can from Excel, PPT and other MS office apps. Reinslalled Adobe, updated Office, and Adobe no help! Also I can create a pdf from the MS Word and it is using the Adobe 9.
-
Lightroom 5 - Lens correction / correction objectif - Sony Alpha A7 SEL2870
Hello everybody. I download lightroom 5 (trial version). I shoot in Raw with my Sony Alpha A7 with the basic lens 28-70 (SEL2870). I didn't found the correction for my lens. The version is (I think) update. How can I do? Thanks Hello tout le monde. J
-
I hope Apple adds a 'back' button to the system. It would make a big difference to be able to NOT have to start over every time I chase a link from an email and then have to get back to mail, and it would be generally helpful. Anyone know why there i