My ipod doesn´t charge the battery with ios6, what should i do?

I have updated the system to ios 6, but after that change I have noted that my ipod doesn´t charge the battety, I have checked the cable with other ipod (ios5) and it´s working, also when I connect it to my computer, it can´t be detected, what should i do? I can´t find how to solve it.. please help me

See the not-charging topic of:
iPod touch: Hardware troubleshooting
Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, foreign material and cracked or broken plastic.

Similar Messages

  • TA44551 my gen 4 iPod doesn't charge, the usb cable is good(works on other apple products) What should i do?

    my gen 4 iPod doesn't charge, the usb cable is good(works on other apple products) What should i do?

    What normally happens is most people take showers and listen to thier ipods or live around many sources of humidity.  Moisture corrodes the 30 pin connector on the ipod touch.  Clean and inspect the ipod touch's connection pins to resolve most charging/ sync issues.. The pins could also be dirty, bent or broken.  If dirty: Take 91% rubbing alcohol, dip a tooth brush into it, shake the excessive alcohol off leaving the brush damp(don't use to much alcohol, it should not be dripping).  Careful!!! The Pins are Very Fragile! Gently brush the connector pins, long ways, left to right in a few second bursts, inspecting the pins as you go...   If you have an eye loop or magnifying glass you can see inside the connector easily and see if the pins look dirty or bent or broken.  If they are bent you have to VERY GENTLY stand them back up.  If they are bent very far down, chances are you will snap them off trying to straighten them back up.  If they are not severely bent over, use a very small flat head precision screw driver to bend the pin back parallel with the good pins.  Pease note: certain pins are used by the wire for different things such as sync or charging... If your pins are broken off, do a search and find out what the individual pins on the ipod 30 pin connector do to see what is affected.  Worst case is your pins are broken off.  U can attempt to solder the broken pins back on without opening the ipod touch, which is super difficult to do, or you can open the touch and repair/replace to 30 pin connector entirely.  U will need to do some micro soldering to say to least! Don't attempt unless you are confident in your soldering skills and research how to open an ipod touch? You will need some specific tools and watch out for floating LINT!  Get some canned air ;) use a small 1/2 second bursts from 4-6" away because it will steam up you touch if used for to long. Good luck!

  • My brand new Ipad 2 is not charging the battery with py PC thru USB. Is that normal? When I plug it directly into the wall, it works... Thanks! Sam

    My brand new Ipad 2 is not charging the battery with py PC thru USB. Is that normal? When I plug it directly into the wall, it works... Thanks! Sam

    It talks extensively about charging in the user guide, and how USB ports on PCs and older Macs may not provide sufficient power to charge the iPad.  The user guide is available for free from the iBook store (accessed directly via the iPad iBooks app).
    My iPad charges fine when plugged in to the back of my iMac, but I would always prefer to use the mains adaptor to save the strain on my USB circuits (which can wear out if used heavily to power external devices).

  • MacBook Pro 2011 doesn't charge the battery at all. Only works with the powercord. Reset SMC already. Ideas?

    The battery doesn't charge at all anymore.
    My Macbook pro suddenly stopped working without the cord plugged in. 
    And when the laptop is switched off, it switches on by its own as soon as I plug it in.
    I reset the SMC, to no avail.
    Any tips?
    Thanks.
    MacBook Pro (13-inch Early 2011), Mac OS X (10.6.8), 2.3GHz Intel Core i5 processer

    If it has a replaceable battery, then consider replacing it.
    Open System Profiler in Utilities folder. After it opens click on the Power entry in the sidebar. See what it reports for your battery. If it's no longer usable it will generally say "Service."
    If you don't have a user-replaceable battery, then take it to an Apple Store.

  • I was updating my ipod and its frozen on the update circle until the battery drains. What should i do? I already tried reseting it does'nt work

    As i was updating my ipod it froze on the update circle. I've tried reseting it but it turns on normally and goes to the update circle until the battery drains. P,ease help.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer          
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • I cannot get my ipod shuffle to charge the battery

    It tells me it is sync up but will not charge.  Oddly, when i go to eject it from my laptop it does not show up. It is a great device for walking.  Thank you for any advice.
    csg1958

    Hello csg1958
    Start here for troubleshooting your iPod shuffle.
    iPod shuffle troubleshooting and service FAQ
    http://support.apple.com/kb/TS1412
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • When I plug my iPod into the charger and it's done charging the battery goes on and off and it wakes me up at night please tell me how to fix this!

    When my iPod is done charging the battery noise
    Goes on and off and it's very annoying and I can't figure out
    What it is and it goes off when I sleep walking me up please
    Help me!!

    After a short time the iPod's screen should automatically go off? Does that happen?
    Cover the iPod with something so the screen light does not bother yuu

  • Another lenovo (W530) doesn't charge a battery

    Hi folks!
    I was a happy owner of brand new W530 machine untill I mentioned that it doesn't charge the battery.
    The machine came to me with 94% charged batt and since then it got to 4% mark.
    Symptoms:
    -Lenovo Power Manager detects the batt, says it's good and charging, doesn't estimate how long it would get to charge it.
    -Windows power manager says "Pluged in, charging"
    -W530 worked perfectly on the batt, I made it to drain the battery by unplugging power cord and running "heavy" applications.
    -The battery indicator on top cover is flashing orange once per second.
    -AC Power source outputs 20.5V, BIOS v.1.08, Lenovo software of the most current versions.
    What I've tried:
    -Uninstalling and reinstalling Lenovo Power Manager.
    -Enabling/Disabling/Uninstalling "Microsoft ACPI - blah-blah"
    -Unplugging power cord and battery, pressing power button for 40 seconds and assebmling all together.
    Any working ideas are wellcome.
    Solved!
    Go to Solution.

    What have happened since my last post:
    Note: Lenovo power manager used to estimate power consumption 60-70W even if W530 in idle state. I thought it's ok, w530 is a powerful machine with 170W AC adapter.
    Lenovo was charging the battery very  slow (estimated 14 hours to full from 40%), with stops.
    I was looking through this forum and desided to check if I have CUDA enabled. I launched GPU-Z and found out that K2000M was suspened. Then device manager showed me troubles with K2000M. I reinstalled it with fresh drivers and rebooted. Despite K2000M was functioning since then, power consumtion is floating between 28-33W (almost idle state) and the battery is being charged like it should (1% per 2-3min).
    Now I may confirm that my lenovo works fine. 
    BTW It's still about 0.35V between first and last battery contacts. Looks like w530 doesn't output charging current if it doesn't detect any battery.
    PS Still no CUDA support

  • Thinkpad Yoga S1 Runs off AC but won't charge the battery

    I have recently purchased an S1, which is now having an issue that I can't seem to resolve on my own. The laptop works (almost) perfectly on A/C, but doesn't charge the battery. I noticed yesterday the battery was low (which was surprising, because I had only recently unplugged it) - so I plugged it in to charge.At which point, the battery icon in the system tray stated "8% (plugged in, not charging).I've tried the following to fix this: 1) Leaving it plugged in overnight completely off. 2) Running the battery calibration (fails w/ unexpected error). 3) Tried turning off battery optimization (Option is removed in newer version of drivers, so NA to my issue). 4) Tried reinstalling the power management drivers anyway (even though I already had the newer version). 5) Holding down the power button for 30 seconds, both plugged in and not plugged in (suggestion from forum). 6) Holding down the reset button (pin reset on the mobo) for 30 seconds, both plugged in and not plugged in. 7) Charging from BIOS. 8) Letting the battery run down to 0% in BIOS, then rebooting on A/C (another forum suggestion).  Now I'm just at 0% plugged in and not charging. Previously I said the computer almost worked perfectly, the almost is that the CPU is stuck at ~800mhz, even with all power management turned off (including Speedstep in BIOS) and the power profile set to high performance. Can anyone think of anything else I can try before I give up and send this thing back? It was working perfectly for the last couple of weeks or so, including getting ~ 4, 5 hours of battery life, so unless the battery failed very suddenly I can't imagine why it would just start refusing to charge.

    well I replaced the battery with another one I bought (exact same model for the battery SONY 45N1705, I was hoping I would get another battery version because I notice there is an update for the other battery revision that fixes issues with battery stopped charging. http://support.lenovo.com/us/en/downloads/ds001322. I forced the bios update from 1.07 to latest 1.24 using olydbg to skip the battery check. this did not help with anything relating to the battery. now I am stuck again where I was at the beginning..... im looking at buying a board replacement.... also I was looking at replacing the power supply but I check the voltage and the amps, and it is correctly matching what is written on the back of the laptop. still getting the 0% plugged in and charging.

  • I have an ipod nano 5th generation. the problem with it's that it doesn't show in itunes when connected to the laptop and it switches on on its own and songs start playing the battery gets consumed too fast after full charge. what is the actual problem?

    i have an ipod nano 5th generation. the problem with it's that it doesn't show in itunes when connected to the laptop and it switches on on its own and songs start playing the battery gets consumed too fast after full charge. what is the actual problem?

    What have you tried so far in terms of troubleshooting this issue?  Are you plugging the iPod into a high powered USB 2.0 port on the back of your PC? Have you tried a different USB cable?
    What happens if you try to reset the device with it still connected to the PC?
    How to reset iPod
    Has this iPod ever worked on this PC or is this the first time you have time you have tried connecting it?
    Have you carefully worked through each and every single suggestion in this Apple support document?
    iPod not recognized in 'My Computer' and in iTunes for Windows
    B-rock

  • Does the iPod nano come with a means to charge the battery?

    Does the iPod nano come with a means to charge the battery?

    Yes it comes with a syncing cable that you can connect to your PC's USB ports to charge or you can connect it to an Apple wall adapater (sold seperately).
    B-rock

  • My IPad screen is dark and will not turn on. I have charged the battery and nothing. I have tried to reset the device as well with no luck. Any suggestions?

    My IPad screen is dark and will not turn on. I have charged the battery and no luck. I have tried to restart it multiple times with no luck. During the restart, the screen will flicker like it is trying to restart but the silver apple never shows. Any suggestions?

    Please tell me that it has NEVER been jailbroke.  If it has never been jailbroke, here are some standard repair procedures:
    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  It could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow the on-screen directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here.  You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again.  Also, read this.

  • I have an ipod mini. and when it comes on it shows the battery with a ! mark. What does this mean?

    I have an ipod mini. When it comes on it shows the battery with  a !   What does that mean?

    That just usually means the battery needs to be recharged.  If you have already tried recharging it, see some of the troubleshooting steps in this Apple support document.
    Charging your iPod battery
    B-rock

  • Am having problems with my Zeppelin music player and iPod classic. The Zeppelin, bought Dec '12, and the iPod, bought same time, used to work fine but now when I attach iPod to Zeppelin I get a message that says the iPod doesn't support the accesory!

    I bought a Zeppelin music player and iPod classic in December 2012, and all went well until I last synched the iPod with iTunes, and now I get a message saying that the iPod doesn't recognise the attached accessory when I try to connect it to the Zeppelin. I did recently update to the latest iTunes version-could this be the problem, and if so how do I cure it? All help appreciated.

    It's still charging when you plug it in. That just means it won't play music out the speaker. If that's what you were looking to do, they have speakers for iPods.
    -Molly

  • My iPad 2 wifi keeps rebooting , and it doesn't update the battery status . Can anyone help me with this one?

    My Ipad 2 keeps rebooting and it doesn't update the battery status anymore.
    Here is the error
    Incident Identifier: D729F1DF-6960-4847-A6C3-75351A67AE9B
    CrashReporter Key:   c7e1a298a42fc9bbb41b4ed79ff29a1655de12a6
    Hardware Model:      iPad2,1
    Date/Time:       2013-02-16 02:58:06.115 -0800
    OS Version:      iOS 6.0 (10A403)
    CRC ERR!
    I had this problem for quiet sometime now, and I would really appreciate your help. THANKS

    I did try restoring the ipad a couple of times and it didn't do the trick. I also tried updating the firmware.
    The only thing that worked for a while when the ipad - on it's own - rebooted itself into a black screen with white text and automatically fixed the issue. It worked perfectly for a couple of months but it came back after I forgot to charge the ipad , does anyone know how I can force the ipad into that screen again ?

Maybe you are looking for

  • How to get a value for Select One Choice in the backing bean

    Friends, Does any one have any idea, how to get the value of a selected item value from the Select One Choice component in the backing bean iin valueChangeListener method. Right now I am always getting the sequence of the selected item, instead the a

  • IPhone Photos App Photo Library has no Delete button

    iPhone 4S iOS 6.1.3 Photos App Photo Library Album Pictures have no Delete button in the bottom right bottom corner like found in Camera Roll Album Pictures. How do I delete obsolescent photos on the iPhone Photo Library Album without sync deleting i

  • Is there a terminal command to disable the "Boing' sound ?

    Hello, Everyone I was wondering if any one knows if there is a terminal command that can be used to disable the "boing" sound that folders and files make (in Tiger) as they are being moved about the desktop and or into finder windows. A couple of peo

  • Error: e_auth_bad_device_key _or_pkcs12

    Tengo varios ebooks, los cuales puede abrir en el momento de la descarga sin ningún problema, y ya he empezado a leer, sin embargo, ahora no me deja abrirlos, me dice que la clave está dañada y me muestra este error, tengo el adobe digital editions 2

  • Internal number assignment for materials

    Hi, all. I need your help. In my system, material code is 5 digit number. Material code is created and assigned internally. But If i terminate transaction - MM01 when I create material master, next material code is not sequencial. ex.)    last materi