My iPod Nano 5th G. Won't turn on off the charger!?

I recently just found my iPod since it's been lost, I can't understand why it won't turn on when it's not on the charger? It comes on when I put the charger in, thats fine, an I can listen to music and all, it even shows the bolt on the battery and that it's charging, also shows fine on my computer, it connects an I can sync music but I just don't get why when I take it out the charger it goes off and won't turn back on! I tried looking online on how to reset which I did but no luck not even when when I tried resetting it while charging t still won't come on without the charger connected to it. Unless I'm doing it wrong, I don't get it. It never had that problem, although it's been dead for a really long time but does it make a difference? And the battery doesn't show full, it still shows it charging you know when it moving ? And I can't even tell if the battery has gotten at least half way charged cause it goes right off when I take the charger out. Its been about 7-8 hours that I had it on and off the charger . Can you help me? Does the battery have be completely full to where it's still and green ? Not moving back and forth meaning it's not charged at all? Some gadgets don't show the battery is at least half way. On the computer on iTunes, it says it's up to date

Hello undertow5613,
I would be concerned as well if my iPod nano was not powering on.  I found a resource that I think would help in a situation like this.
I recommend following the steps in this troubleshooting assistant:
iPod nano (5th generation) Troubleshooting Assistant
http://www.apple.com/support/ipod/five_rs/nano5gen/
Thank you for posting in the Apple Support Communities. 
Best,
Sheila M.

Similar Messages

  • IPod Touch 5th Generation won't turn on and the home button is broken, followed the steps from another thread but it's still not working

    I have an iPod Touch 5th Generation with iOS 8.1, my home button is broken and I've been using AssistiveTouch for months now. Today I just locked my iPod and it wouldn't unlock again, it doesn't respond at all, it won't turn on. It was almost fully charged, so it's not the battery. I followed the steps from this thread, but I'm still getting the "USBMuxListenerCreate: No Error" message in CMD Prompt. I bought my iPod abroad and even though I do have the warranty, I've been told at the iStore that it's not valid here, so going to the store isn't really an option. Any ideas how to solve this?

    Sorry, but without a working home button it is not possible to reset or restore your device. You should visit an Authorized Appel Service Provider or Apple Store to get it serviced. The warranty for an iPod is not limited to the country where it has been bought, check here: one-year limited warranty
    Jailbraking the device will void the warranty.
    You can check the warranty status by inserting the serial number on this page: https://selfsolve.apple.com/agreementWarrantyDynamic.do
    A list of Authorized Apple Service Providers can be found here: iPod touch - Contact Us - Apple Support

  • My iPod touch 5th generation won't turn on after the new iOS update

    I've just updated my iPod touch 5th generation to the iOS 8.1.1. (or whatever the newest update is) but once it updated, it now won't turn back on. I've tried plugging it into multiple chargers and computers just in case it wasn't charged, and tired turning it on, but all I get is the apple logo and nothing's happening. What can I do? I haven't backed it up this month and I don't want to loose all my stuff. Thanks.

    Try the following. It is very likely that the iPod will have to be erased:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     
    In the future make sure yo backup before updating. I always backup to both iTunes and iCloud before updating .

  • My ipod nano (square - 4GB) won't turn on even when charging, how can i get it to turn on?, my ipod nano (square - 4GB) won't turn on even when charging, how can i get it to turn on?

    my ipod nano (4GB, 3rd generation) won't turn on or charge after running out of battery? How can I get it to turn on?

    How long have you left it to charge?  At least half an hour or more?  Did you try a hard reset after leaving it to start for a few hours? To reset the device, press and hold both the Select (Center) and Menu buttons together long enough for the Apple logo to appear.
    B-rock

  • My iPod touch 5th gen won't turn on past the apple logo, do I need to restore to factory settings? If so, is there a way to save my photos?

    I've had my iPod touch 5th gen for a little over half a year now, haven't had any issues until now. Yesterday it randomly shut down, and when I try to turn it back on, the apple logo shows up but the iPod just stays on that screen, it doesn't turn on any further. I think I might need to restore it to the factory settings to get it to work again, but I'm concerned that I'm going to lose all my photos. I found the backup folder in my computer but it doesn't have any files in it. I have over 600 pictures on my iPod and I really don't want to lose them all. Is there a way that I can either get my iPod to work again without restoring, or a way that I can extract the photos without the iPod actually being in functioning condition? The computer doesn't recognize the device when it gets connected via the USB. Thanks!

    - Connect the iPod to your computer and try to make a backup
    iOS: How to back up and restore your content
    - Next reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    and try making a backup again. If you can't then there is no way of getting the info off the iPod unless data recovery company can do it. Not cheap.
    - If photos are in an existing iPod backup (iTune>Preferences>Devices  for iTunes backup or an iCloud backu) then restore from that backup. See the restore topic of:
    iOS: How to back up
    - If you used PhotoStream then try getting them from your PhotoStream. See that topic of:
    iOS: Importing personal photos and videos from iOS devices to your computer

  • My ipod nano 5th generation won't sync. It says disc cannot be found.

    My iPod nano 5th generation won't sync for some reason. It is almost like my PC is reading it as a regular mp3 player. I have to manually open itunes when I connect it.

    The computer won't see them as the same iPod despite the name.
    You might want to reload Windows on your computer or reinstall the USB root driver.

  • My ipod touch 5th generation will not turn on and the home button doesn't work. what do i do?

    Hello my name is Leslie and i would like to ask you guys a question on how to fix my ipod or what is wrong with it. My ipod touch 5th generation will not turn on and the home button doesn't work. what can i do to fix it ?

    Has the home button worked in the past, or is this been something that hasn't worked for some time? The only way to reset the device is with the sleep/wake (power) and home buttons together. Without it, you would have to wait until the battery dies and then plug it in to try and reset it. The Home button is used for several user troubleshooting steps. Without it, you cannot perform a reset, put the device into recovery mode, or place it in DFU mode. You need to get the home button repaired.

  • My macbook black shutdown during a thunder storm , what do i need to? it won't turn on and the charger light is not on green or on at all..have i fried it?

    my macbook black shutdown during a thunder storm , what do i need to? it won't turn on and the charger light is not on green or on at all..have i fried it?please help a.s.a.p...

    Most likely.
    You can try to boot from the Install DVD for your Mac and run AHT from there if it boots.
    If not it sounds like it is time to take it to Apple for repair.
    Allan

  • My iPod Touch 5th gen won't turn on

    My iPod touch 5th gen was working fine and was fully charged and then it just shut off and won't turn back on.  There has been no damage to it from anything and there was no reason it should've shut off.  I tried holding down the lock button for a minute and I also tried plugging it in..still nothing.  I can't hold down the home button and lock button at the same time because the home button has been stuck down for about a month.  What else can I try to make it work?

    Turn on without Home/Power Button

  • My iPod touch 5th gen won't turn on after updating to iOS 8 using the computer,help!?

    On my computer (using windows) I tried to update my iPod touch 5th gen to iOS 8 using iTunes, using this website http://www.gottabemobile.com/2014/09/17/the-secret-to-skipping-long-ios-8-downlo ads-and-problems/ as a guide.
    It kept coming up with this error http://support.apple.com/en-us/HT201442 after the update.
    Now my iPod won't turn on and it shows the charger with the lightening with an arrow above it pointing to the iTunes logo.
    So i plugged it into iTunes but i don't know what i'm supposed to do, any help?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • I have a 4th generation iPod nano 4th and when I turn it on, the screen won't progress passed the main screen with the Apple logo. What should I do?

    I have a 4th generation 8GB iPod nano and it will not progress past the blank screen with the white apple logo on it. I have charged it fully and tried to restart it by pressing and holding the menu buttons for 3-7 seconds. The devices screen will turn off and then, after a couple of seconds, the screen with the Apple logo will appear again. This screen will remain lit until the iPod runs out of battery again. I have tried plugging it into my Macbook Pro. I have the newest versions of iTunes software and OS X Mavericks. The computer will not recognize the iPod and the device will not show up in the computers list of devices. I looked up the troubleshooting for the device and found out how to put the device into disk mode. I followed the intructions but the iPod would not go into disk mode. The screen still displayed the Apple logo and would not set into disk mode. I fear that I have run out of options. I have come to this forum in hopes that I can still salvage my device. If there is anything I can do, please loet me know so I can try it. If not, I am affraid I will have to go to an Apple store of authorized retailer and have it repaired or replaced.

    Try manually connecting the device to your PC in Disk Mode and then restoring it iTunes.
    From http://support.apple.com/kb/HT1363
    Putting iPod devices with a Click Wheel into Disk Mode
    If necessary, verify that your iPod has a Click Wheel.
    Before placing the iPod into Disk Mode, verify that it is charged.
    Toggle the Hold switch on and off (set it to Hold, then turn it off again.)
    Press and hold the Menu and Select buttons for at least six seconds, until the Apple logo appears.
    When the Apple logo appears, release the Menu and Select buttons and immediately press and hold the Select and the Play/Pause buttons until the Disk Mode screen appears.
    Connect the iPod to your computer; the screen on the iPod will should say "Do not disconnect".
    If you are having difficulty putting your iPod into Disk Mode, set it on a flat surface. Make sure that the finger pressing the Select button is not touching the Click Wheel. Also make sure that you are pressing the Play/Pause button toward the outside of the Click Wheel and not near the center. If you are still unable to put your iPod into Disk Mode, use one finger from one hand to press the Select button, and one finger from the other hand to press the Play/Pause button.
    B-rock

  • My iPod nano 5th generation won't work on my windows 8.1 laptop,help?

    Ok last year I got my first Toshiba laptop for Christmas and had my iPod nano since 2010. The iPod was fittied in perfectly when I first got the laptop and there was no problem with it until a few days ago it wasnt able to recognize the device at all. I tried uninstalling iTunes, turning off the laptop and putting the ipod in plus taking it out god knows how much, it still wouldn't recognize the device! Ive never seen it to fail although we have an old Windows XP computer and there was no problem regonizing it but I prefer to have the iPod on my own laptop computer so I can install purchases easily! Can somebody please tell me how to solve this problem?!

    Hi Gglove,
    Welcome to the Support Communities!
    The article below may be able to help you with this issue.  You may need to remove and reinstall the iTunes software for Windows 8.  Click on the link to see more details and screenshots.
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    http://support.apple.com/kb/HT1923?viewlocale=en_US
    Cheers,
    - Judy

  • Ipod nano 3rd generation won't turn on

    iPod nano 3rd gen.   Suddenly stopped working, Should I assume it is shot or anyone have any solutions.
    Was recently working, then a white screen and static.   Wont power on, and iTunes does not recognize it. 

    Howdy maggie63,
    It sounds like your iPod nano will not turn on, or respond to anything. I want to recommend 2 things here.
    First, reset the iPod with these steps:
    Reset
    To reset your iPod:
    1. Toggle the Hold switch on and off. (Slide it to Hold, then turn it off again.)
    2. Press and hold the Menu and Center (Select) buttons simultaneously until the Apple logo appears, about 6 to 10 seconds. You may need to repeat this step.
    Tip:
    If you are having difficulty resetting your iPod, set it on a flat surface. Make sure the finger pressing the Select button is not touching any part of the click wheel. Also make sure that you are pressing the Menu button toward the outside of the click wheel, and not near the center.
    If the above steps did not work, try connecting iPod to a power adapter and plug the power adapter into an electrical outlet, or connect iPod to your computer. Make sure the computer is turned on and isn't set to go to sleep.
    If that does not work I would next try to restore the iPod with iTunes:
    1. Make sure you've reinstalled the latest version of iTunes.
    2. Open iTunes, and then connect your iPod to your computer.
    3. After a few moments, it will appear in the source list in iTunes. If the iPod's display doesn't show "Connected" or "Do not disconnect" you may need to put the iPod into disk mode to proceed.
    4. Select your iPod in the source list and you will see information about it appear in the Summary tab of the main iTunes windows.
    5. Click the Restore button. You will be prompted with one or more restore options that may prompt iTunes to automatically download of the latest iPod Software. The 4 possible restore options are:
    Restore Option 1: Restore - Restores with same iPod Software version already on iPod.
    Restore Option 2: Use Same Version - Restores with same iPod Software version already on iPod, even though a newer version is available.
    Restore Option 3: Use Newest Version - Restores with latest iPod Software version on your computer.
    Restore Option 4: Restore and Update - Restores with latest iPod Software version on your computer.
    6. A message will appear prompting you to enter an administrator's name and password.
    7. A progress bar will appear on the computer screen indicating that the first stage of the restore process has started. When this stage is completed, iTunes will instruct you to leave iPod connected to your computer to complete restore.
    8. During the stage 2 of the restore process, the iPod will show an Apple logo as well as a progress bar at the bottom of the display. It is critical that the iPod remains connected to the computer or iPod Power adapter during this stage. Note: The progress bar may be difficult to see since the backlight on the iPod display may be off.
    9. After stage 2 of the restore process is complete and the iPod is connected to the computer, the iTunes Setup Assistant window will appear asking you to name your iPod and choose your syncing preferences similar to when you connected your iPod for the first time.
    Both these bits of info are from this article named:
    iPod nano (3rd generation) Troubleshooting Assistant
    http://www.apple.com/support/ipod/five_rs/nano3gen/#
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • My ipod touch 5th gen won't turn on or reset and my computer won't recognise it. It's 1 day old and all I did was try to plug it into the speaker system

    My ipod touch 5th generation was purchased brand new yesterday. After charging it and loading my music i went to plug it into my icoustic dock which I got as a bundle with the ipod only to have my ipod screen go blank and now it refuses to turn on, reset or get recognised by my computer or itunes. I have the latests software as it was only uploaded last night. Should I be taking it back to the shop? Has anyone else had a similar problem?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • Re : My ipod nano 3rd generations won't turn on . ? Help

    My ipod nano wont turn on . itried to change it but still nothing . Can someone help me .?

    Try resetting it, hold down the center button and the menu button at the same time for about 15-30 seconds or when the apple appears let go of both buttons. If this does not work, do the same thing while it is plugged into the computer or outlet.

Maybe you are looking for

  • File Upload using PRC API's

    Guys, I am trying to upload a new document using PRC API's. Below is required code snippet that i am using. IRemoteDocument remoteDoc = documentManager.createRemoteDocument(folderID,dataSourceID,document.getPath()); remoteDoc.setOverrideName(document

  • Exporting to a word doc- what's the point? Why does it not work?

    hello, whenever I export and PDF into a word document in order to highlight and make notes, the word document either says "unable to read document" or there are lines through the word document and it's not in a format in which I can highlight and mak

  • Penalty costs in the optimizer

    I have a requirement in my project where the sales orders should have a higher priority than the forecast.  I have defined the delay penalty for the sales orders as 1 per unit per day and the delay penalty for the forecast as 0.01 per unit per day. 

  • Display record details

    I created a program that saves an entry to a customer table, ztable. Now I want to edit any entries from that table and I need to display the details. Ex. If I select record1 on in the first parameters, all other parameters will show the other detail

  • First and Last Word on Page

    Hi, I am trying to create a document that is similar to a dictionary or an index of information. I want the first and last word on each page to be displayed automatically at the top corner and bottom corner of each page, to make navigation in the doc