My ipod nano 6th gen wont charge, turn on or respond to anything i have done i have tried the troubleshooting and nothing works. I have droped it once but it work for about a month after and i havent wet it any tips would be much apriciated! thanks

My ipod nano 6th gen wont charge, turn on or respond to anything i have done. I have tried the troubleshooting and nothing works. I have droped it once but it work for about a month after and i havent wet it. any tips would be much apriciated! thanks

Try:                                               
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable       
- Try on another computer                            
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar                                     

Similar Messages

  • TA44551 Apple ipod nano 6th generation wont charge on pC, mains or car.

    My ipod nano 6th generation wont charge, either through mains, car or computer USB charger.  Had it one month, bought it from Amazon.  Just dead, wont wake up.  When it had charge tried master reset etc. still not able to charge or recognised/charge on PC

    It'll need to charge for a while before it will turn on. Leave it to charge for a couple of hours, then try again.

  • My ipod nano 6th gen will only turn on when plugged into a power source.

    My ipod nano 6th gen ONLY turns on when it is plugged into a power source. As soon as I unplug it, it turns off. I also tried to reset it and it did not help. Any suggestions? 

    Howdy mela1223,
    If I understand correctly your iPod will not stay on unless you have the charger plugged in even after resetting it. Normally this would indicate a hardware issue that would need a repair but to cover all the bases before that, the last troubleshooting that can be done for it would be to restore it with iTunes on a computer. 
    Restoring iPod to factory settings - Apple Support
    How to restore iPod
    Verify that you have an active Internet connection, because you may need to download new versions of the iTunes and iPod Software.
    Download and install the latest version of iTunes if necessary.
    Open iTunes. Connect your iPod to your computer using the USB or FireWire cable that came with your iPod.
    After a few moments, your iPod will appear in the Source panel in iTunes.
    Select your iPod in the Source panel. You will see information about your iPod appear in the Summary tab of the main iTunes window.
    Click Restore.
    If you are using a Mac, you will be asked to enter an administrator’s name and password.
    A progress bar will appear on the computer screen, indicating that stage one of the restore process has begun. When this stage is done, iTunes will present one of two messages with instructions specific to the iPod model you are restoring.
    Disconnect iPod and connect it to iPod Power Adapter (typically applies to older iPod models).
    Leave iPod connected to computer to complete restore (typically applies newer iPod models).
    During stage two of the restore process, the iPod displays an Apple logo as well as a progress bar at the bottom of the display. It is critical that the iPod remain connected to the computer or iPod power adapter during this stage. 
    Note: The progress bar may be difficult to see, because the backlight on the iPod display may be off.
    After stage two of the restore process is complete, the iTunes Setup Assistant window will appear. It will ask you to name your iPod and choose your syncing preferences, as it did when you connected your iPod for the first time.
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • Ipod Nano 6th gen not charging at all

    I have an Ipod Nano 7th Gen whichn was bought in Nov 2012 for my daughter.  the problem is that when I connect the Ipod to the computer to charge all of a sudden it is just not working at all.  And gives the error (USB Device not recoginesed) 'One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it.'  Can some one please help 

    Ok thanks all but got the remedy from a guy that had the same problem on the IPad.  All one has to do is to press the power button and the home butoon together for 10sec and it will reset the Ipod

  • My iPod Nano 4th Gen wont charge, sync, or turn on anymore.

    I have a blue iPod nano, 4th generation and it refuses to cooperate. I have the standard charge cord that plugs into the PC via USB and I have the wall adapter and when you plug it into either/or nothing happens. Right now it just keeps trying to reset itself over and over and over. I bought a brand new cord from The Source and plugged it in, still nothing. On top of all this, last week when I plugged it in, it gave me an error message saying "USB device not recognized." Any help would be greatly appreciated!

    Did you already try the troublshooting assistant?
    Apple - Support - iPod Troubleshooting Assistant
    Or Restoring iPod to factory settings
    Did you check the docking port for any kind of debris or lint?
    If it is not recognized in iTunes, try this: iPod not appearing in iTunes and iTunes for Windows: Device Connectivity Tests

  • IPod Nano 1st Gen Wont Charge With USB Cable

    I just purchased a brand new 4 gb white 1st gen iPod nano. From the moment I took it out of the packaging and tried to charge it with the provided USB cable I noticed it was not working. No response at all, nothing was getting into the iPod. I tried multiple USB cables with equal luck.
    I have a Dension I.C.E Link Plus in my car, I figured I'd try it, sure enough the iPod Nano began charging and booted up. I finished charging it to a full charge in my car.
    After a few days of use, I went to charge my iPod via USB cable and when I plug it in, it connects to the computer I can transfer songs perfectly but it constantly states that the iPod is "charged" displaying the plug battery icon not the flashing thunder bolt. So I figured it was charged, when I unplugged it from the USB cable the battery meter was clearly not charged.
    So, I assumed it was my computer USB ports being messed up so I purchased a A/C Wall Charger Adapter. Once again it would only display "charged" so far the only thing that will charge my nano is my car.
    With the A/C wall charger I have even tried multiple cables with no luck.
    CAN SOMEONE HELP ME!?!?!? I thought it was suppose to charge with the provided USB cable? Thanks!

    Yes you have a one year warranty from the date of purchase from Apple. Go to this link and on the bottom right hand side it will ask you to enter your serial number and will tell you if you are still under warranty. http://www.apple.com/support/
    If you are you can take it to a Apple store, or request service online here http://depot.info.apple.com/ipod/
    If it is out of warranty you can google a third party service provider and get it serviced out of warranty. There are two that I know of that provide free diagnostic service. You only pay for shipping and they will tell you what is wrong and what it will cost to fix. They are ifixipodsfast.com and ipodmods.com but there are others also (I just have no experience with them) Good luck and as was stated it should charge from your usb. and just for grins, look at the docking connector on your ipod and see if there is any obstruction that is obvious.

  • Ipod nano 2nd gen wont charge, or show up on itunes or the pc itself

    hey my ipod nano 4gb when plugged in wont show up on my pc or in itunes. it doesnt even charge. i've tried restarting the computer and reinstalling itunes. other ipods work on it fine. ive tried it on other computers and it doesnt work either. i have a set of speakers and it charges and plays through them without any problems.
    PLEASE HELP!

    I had the exact same problem!!!! As far as I know their no good solution exept what I did....
    1. go back to the store
    2. Explain the problem
    3. Get them to take the iPod back and get another mp3 player that roughly costs the same. (I swapped my iPod for a creative zen-v...)
    Good luck getting it to work or good luck in the store!!!

  • Does the iPod Nano (6th gen.) charge when plugged in in the car?

    I just bought it yesterday and had it plugged in in the car, yet it still lost power. Is it supposed to?
    love and hugs xox
    Timothy

    Mi ipod Nano lo utilice dos horas y empeso a sonar un ruido luego deja de sonar no lo reinicio lo actualice y nada que puede ser. Gracias
    My iPod Nano to use it two hours and get started ringing noise then
    not stop ringing update and reboot nothing that can be.
    thanks

  • HT1459 MY IPOD NANO 6TH GENERATION WILL NOT TURN ON I GOT IT FOR CHRISTMAS AND PLAYED THE RADIO ON IT WITH OUT PLUGING IT INOT ITUNES AND I WAS WONERING HOW TO FIX IT ?

    hi my ipod nano 6th generation will not turn on what should i do ...no batery left and never pluged it into itunes

    Hi meganisawsome,
    If your iPod will not turn on and you are getting indicators that there is no battery left, the first step would be to make sure that the iPod has been charged correctly. You may find the following article useful:
    Apple Support: Charging your iPod battery
    http://support.apple.com/kb/HT1384
    If you are still having issues after charging, you may want to look at this article:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS3474
    Regards,
    - Brenden

  • How much will apple charge me for fixing a cracked ipod nano 6th gen screen??

    Well I don't have any warranty and i want to get my ipod nano fixed! So how much will apple charge me to fix a cracked ipod nano 6th gen screen????

    They won't actually "fix" the iPod, but instead will replace it with an exact refurbished replica.  See this page for pricing.
    http://www.apple.com/support/ipod/service/prices/
    B-rock

  • My ipod nano 6th Gen. bought 5th Jan 2011 suddenly cannot be switched on. Last use is just 3h ago and everything went perfect til then Even shows no reaction when connected to charging cable. Anyone who can help?

    My ipod nano 6th Gen. bought 5th Jan 2011 suddenly cannot be switched on. Last use is just 3h ago and everything went perfect til then Even shows no reaction when connected to charging cable. Anyone who can help?

    See the Will not turn or screen remains dark section of this Apple support document to start troubleshooting the issue.
    iPod nano (6th generation): Hardware troubleshooting
    B-rock

  • My ipod nano 6th gen fell out of my pockey and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed

    My ipod nano 6th gen fell out of my pocket and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed? It is pretty frustrating, it fell from about 3 feet out of my pocket and now looks like it was beaten by a hammer.

    Debbie:
    deborahfromwindsor wrote:
    he advises restarting by inserting the OSX disc and pressing down the C button to reboot from there then selecting disk utility, hard disk and repair.... Does he mean me to hold down the C key on the alpha keyboard or the ctrl key?
    Should I just ask for my money back??? If it is a simple repair do I just literally push the disc in, push the power button and hold down the C button?
    That's where I would begin, too, with
    Repair Disk
    Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
    Go to Installer menu (Panther and earlier) or Utilities menu (Tiger) and launch Disk Utility.
    Select your HDD (manufacturer ID) in the left panel.
    Select First Aid in the Main panel.
    (Check S.M.A.R.TStatus of HDD at the bottom of right panel, and report if it saysanything but Verified)
    Click Repair Disk on the bottom right.
    If DU reports disk does not need repairs quit DU and restart.
    If DU reports errors Repair again and again until DU reports disk is repaired.
    If DU reports errors it cannot repair you will need touse autility like TechTool Pro,Drive Geniusor DiskWarrior
    First we need to determine if the issue you are experiencing with the computer is software or hardware based. Once we have gotten things sorted out there should be time enough to make you decision about keeping or returning it.
    cornelius

  • I plugged my ipod nano 6th gen in to the latest version of itunes today and as soon as i plugged it it it turned on automatically as it should when i came back to it 5 mins later, picked it up and it felt warm and it wouldnt turn on. what should i do?

    I plugged my ipod nano 6th gen in to the latest version of itunes today and as soon as i plugged it it it turned on automatically as it should when i came back to it 5 mins later, picked it up and it felt warm and it wouldnt turn on. what should i do?

    I have the same problem and can't seem to figure out what the problem is. I rebuilt my iTunes library and still my 6G nano crahes whenever I load an AAC tune onto it.  MP3s and podcasts all work fine, it's just the AACs... 
    Just *loading* an AAC song will cause the Nano 6G to reboot as soon as it disconnects from Itunes. It will then reboot a few times and then go into recovery mode. :-(
    Karen

  • Ipod nano 6th gen askinh for resore every time i connect and after the restore not showing the sysnced song on ipod

    i have a ipod nano 6th gen, few days back when i tried to add few songs through iTunes it gave me error that it "can't connect to ipod . restore it" so i did and after that i synced al the songs and it showed that my my empty ipod has been up few GB's. after i disconnected , i could not see any song on the ipod . when it connected back the ipod the got same error about restore. i dont know what to do now , please help.

    Hello Singhindia,
    It sounds like you restored your iPod Nano when iTunes prompted you and it appears to sync. When you disconnect it and look at the content, the songs arent there, and when you plug it back into iTunes you get the same message again. I would recommend these troubleshooting sections from the following article to help isolate the issue to hardware or software:
    iPod nano: Error message saying that iPod 'could not be identified properly'
    http://support.apple.com/kb/TS3218
    Verify that iTunes is installed and updated
    Restart the computer
    Verify that Apple Mobile Device Support is installed
    Verify the device's USB connection
    Verify that the Apple Mobile Device Service and iPod service are both running
    Verify that the Apple Mobile Device Driver is installed
    Remove and reinstall iTunes
    If the issue continues, gathering iPod Diagnostics may be helpful for you or for support personnel in identifying the issue.
    Additional Information
    Certain phone connectivity software from vendors such as Samsung, Nokia, Bora, Novatel, and Sony may also cause this issue. If you have such software on your computer:
    Uninstall your Samsung, Nokia, Bora, Novatel, or Sony phone connectivity software and test. Contact the manufacturer of this software for assistance in doing this.
    Remove iTunes and all related Apple software by following this article (for Windows XP), or this article (for Windows Vista and Windows 7).
    After reinstalling iTunes, test the iPod nano.
    If you still need your phone connectivity software that was removed, reinstall this software and test your iPod nano to ensure it still functions with iTunes. Contact the vendor of your phone connectivity software if the issue returns.
    While the error message is different than you are seeing, the troubleshooting is relevant for you.
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • I just got a ipod nano 6th gen, and ive been using it for 2 days, and it seems that the battery just lasts about half a day, on playing 1 to 3 songs in intervals of 1-2 hours. Whats wrong with my ipod?

    I just got a ipod nano 6th gen, and ive been using it for 2 days, and it seems that the battery just lasts about half a day, on playing 1 to 3 songs in intervals of 1-2 hours. Whats wrong with my ipod?

    Your nano would really have nothing to do with it at that point. It is really something between iTunes and whatever server out there on the internet that it is trying to connect to for the update.
    Try posting this one in the iTunes forum, they might have a solution for you.
    i

Maybe you are looking for

  • Windows XP not recognizing wireless networks

    I recently upgrade routers from an old motorola router (about 5 years old), to a new airport extreme. I have a desktop that is running windows 7 and is hardwired into the airport extreme. and i have two ipod's that connect to the airport extreme. How

  • Dimension values display order and record details

    Hi All, I have explicitly ordered my dimension values to be in a logical order instead of alphabetical. Ex: Small, Medium, Large. This works great in the navigation tree but when I view a specific record and it  has those 3 dimvals they are listed in

  • How can in configure mail in tomcat 4.1

    sir , i want to configure tomcat 4.1 server for sending mail from my jsp pages.i got some codes for sending mail using jsp.it needed an smtp server address and default port no. i have theses too.but my problem is my smtp server needed user name and p

  • Good receipt w/o PO

    Dear all     I am unable to save the good receipt through t-code MB1C using 501 movement type    The error occurs:-Could not determine recipients for message type ACPJMM.    plz guide me thanks in advance regards ehtesham

  • Help in loading data from an infocube to another

    all, i have been trying to load data from a consolidation infocube of one BW system to a similar infocube in another BW system I managed to load data by identifying the fist system as the source system the challenge that i m facing is as follows the