My ipod nano 7th gen is stuck on a loop of turning on and off.

My ipod nano 7th gen is stuck on a loop of turning on and off, I've already done the reset, and everything that was recommended on other similar questions.  it isn't recognized by iTunes except in recovery mode where it allows me to restore but then goes right back to turning on and off once i'm back to normal play mode.  Once on recovery mode it works fine and doesn't turn on and off.  I've also uninstalled and reinstalled itunes to avail.  I'm super frustrated and am hoping that I won't need to buy a new one.  Is there anything else I can do before i just toss it out?  i'm getting a bit frustrated just watching my ipod turn on to the apple and then turn right back off.

Hi there tksunrise,
You may find the troubleshooting steps in the article below helpful.
iPod nano (7th generation): Hardware troubleshooting
http://support.apple.com/kb/TS4433
Will not turn on or screen remains dark
Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
If iPod does not turn on after ten minutes, try resetting it while it is still connected to power. Reset the iPod by holding down the Sleep/Wake button and the Home button for at least six seconds or until you see the Apple logo appear.
If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
If the screen remains dark and will not turn on, then your iPod may need service.
Issue not resolved
If the issue is still not resolved, please read this information on servicing your iPod.
-Griff W. 

Similar Messages

  • HT1459 My iPod nano (6th gen) is stuck in a loop.

    I have a 6th generation iPod nano, the blue one, it has worked flawlessly up to this point and I have no idea why it has suddenly failed. It is stuck in restore/recovery mode, where it says I need to connect to itunes and restore it, but when I connect it to my computer, it goes into disk mode and fails to mount. I am running ubuntu (it had no problems mounting) but I also have a windows vm that I can use with it.
    Any help is appreciated,
    J.Runyan

    Hi there tksunrise,
    You may find the troubleshooting steps in the article below helpful.
    iPod nano (7th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS4433
    Will not turn on or screen remains dark
    Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
    If iPod does not turn on after ten minutes, try resetting it while it is still connected to power. Reset the iPod by holding down the Sleep/Wake button and the Home button for at least six seconds or until you see the Apple logo appear.
    If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
    If the screen remains dark and will not turn on, then your iPod may need service.
    Issue not resolved
    If the issue is still not resolved, please read this information on servicing your iPod.
    -Griff W. 

  • Ipod nano 7th gen stuck on apple logo screen

    New iPod nano 7th gen.  At first attempt to upload songs, was prompted to update software.  So, software was updated and as I was installing software update to the iPod, I got a message stating that the iPod was in the process of a restore (I think this is what it said.  I didn't pay a whole lot of attention as i was not expecting any problems).  I continued with the restore because nothing had been uploaded to the iPod yet so nothing would be lost.  At this point, the device has been stuck on the apple logo screen for a couple of hours now.  The only response I can get from it is when I do a reset.  The screen will black as it should and then go right back to the logo and stay.  Please help.....Son not happy as this was one of his Christmas presents this morning.  Really not looking forward to a trip to the apple store on the day after Christmas.

    I am afraid yo need to visit the store and possibly ask for a replacement. In some cases, doing the reset will correct any issues, but by the way you describe it, it freezes with apple logo. Better to get a replacement.

  • My ipod nano (7th gen) seems to be stuck in a loop of turning itself on and off, tried rebooting but keeps doing it?

    My ipod nano (7th gen) seems to be stuck in a loop of turning itself on and off, tried rebooting it but after a while it just starts it again?

    Hi altofts,
    Thanks for using Apple Support Communities.  You can try resetting and restoring your iPod nano to see if that helps with the restart loop:
    How to reset iPod
    http://support.apple.com/kb/HT1320
    Restoring iPod to factory settings
    http://support.apple.com/kb/HT1339
    Cheers,
    - Ari

  • After upgrade to Windows 8.1, ipod nano 7th gen not recognized

    /after upgrading to Windows 8.1, ITunes does not recognize my ipod nano 7th gen.  I have uninstalled and reinstalled ITunes but no luck.  I have gone through all steps in troubleshooting, but it still doesn't recognize it.  Help!

    Hi cindywindy,
    If your iPod Nano is no longer recognized in iTunes after a recent system upgrade, you may find the following article helpful (apologies if you have already seen it):
    Apple Support: iPod not recognized in My Computer and in iTunes for Windows
    http://support.apple.com/kb/ts1369
    Regards,
    - Brenden

  • I recently purchased a bluetooth headphone set that I have been able to pair to my iphone6 , but it is not showing up on my ipod nano 7th gen, anyone else had a similar problem ?

    anyone had trouble syncing a bluetooth headset to an ipod nano 7th gen ? I was able to sync to my iphone6 , but no luck with the ipod, even after a reset & several attempts

    THanks for the suggestion deggie , but I have already tried this without any success. I just mentioned pairing it to prove that the headphones weren't defective. I also tried reaeting the ipod through itunes hoping that might help , but still no detection on the ipod

  • Is there a way to listen to radio on iPod nano 7th gen with Bluetooth headphones?

    I know the iPod nano 7th gen uses the headphones as an antenna. I know there will need to be some sort of antenna attached. Does anybody know if there is an antenna on the market that can be plugged into the headphone jack that will allow audio to be sent to a pair of Bluetooth headphones?

    There is currently no such antenna available.
    B-rock

  • Ipod nano 7th gen not turning on or connecting to laptop??

    My son's ipod nano 7th gen won't turn on and when I connect it to the lap top a message comes up saying device driver not recognised - he was listening to it just last night, can anyone help? He's only had it since his birthday in November.

    I reset the ipod by holding down the power button and the menu button and the apple screen came up after a few moments - this seems to have done the trick!

  • IPod nano 7th gen (brand new) doesn't recognize Headphones

    I have a brand new iPod nano (7th gen), and it doesn't detect when headphones are plugged in. I have read that the problem can ocurr because the headphones are not correctly inserted or that the headphone jack has dust inside. As i always do on a regular basis with mp3 devices, i cleaned out the jack to be sure
    This is what happens:
    When music is not playing i hear a crackle pop sound every 2 seconds or so. My headphones are perfectly fine and work with my Samsung galaxy s4 and my old iPod touch, and my brothers iPhone. Just don't work with iPod nano. I have 3 pairs of headphones all which do not work but I do not have the original headphones. they are so uncomfortable and seems unfair to me that apple would have a one size fits al headphone that only works with the device. I do not intend on switching.
    When I play a song, and then press the sleep/wake button to turn off the display, the music stops. Or if I let the music play, it stops when the screen times out and turns off. These two things occur because the iPod "thinks" that there are no headphones inserted.
    When I try to activate the FM radio, the radio won't start because it says that there is no radio signal (which occurs when no headphones are connected).
    Needless to say, the microphone and volume controls of the iPhone headset, don´t work at all (they even work on the iPod shuffle!).. and because of this, no voice recording for me!
    I have also restored the device in iTunes, and updated with no luck.....
    Thanks in advance for any useful answer!
    iPod nano

    First, make sure the headphones plug is completely inserted into the nano's headphones jack.  It should "click" into place.  The fit may be tighter than expected, especially when new.  There is a sensor in there, and if the plug is not completely inserted, you may get some sound, but the nano will not "sense" the headphones.
    If that is not the problem, you should have the nano looked at under warranty.  It should work with any standard headphones. If there is an Apple Store nearby, you can make a reservation at the store's Genius Bar and take it there.

  • Ipod nano 7th gen not being recognized by itunes

    i have the new hp split x2 laptop running windows 8. i kept ignoring the new itunes update and everything was fine but as soon as i installed it, itunes no longer recognized my ipod nano (7th gen). i have been sitting here for about 2 hours looking for answers so now i am asking for them instead. is there a way to uninstall the last update? i would go to best buy and just have geek squad fix it for free (because im covered for 2 years) but we are currently having a massive snow storm here in NY please help!

    I'm trying to put songs on it

  • I got a new iPod nano 7th gen., but when I tried downloading a video from my iTunes library a message popped up that said: Some of the videos in your iTunes library cannot be copied to your iPod because they cannot be played on this iPod.

    I got a new iPod nano 7th gen, but when i tried downloading a video from my iTunes library a message popped up that said: Soem of the videos in your iTunes library were not copied to yor iPod because they cannot be played on this iPod. What should I do?

    I kept having a similar problem - 3 out of the 10 videos I had on iTunes wouldn't sync. They were in the right format and I KNEW they worked on my iPod because I'd RECORDED them on my iPod. I finally figured out what to do! Go to the movies in your iTunes library. Click on one that does not sync. Click on "Advanced" at the top of iTunes and choose "Create iPod or iPhone version". Once that's finished, be sure you delete the old version so you don't keep getting the error (or have 2 copies of the same video) and sync. This should eliminate the problem. At least it did for me!

  • Does the ipod nano 7th gen work with Belkin Blue tooth In car hands free? Customer support said it did when I bought it, but the box doesn't say it does and I dont want to open it in case I have to return it.

    Does the ipod nano 7th gen work with Belkin Blue tooth In car hands free? Customer support said it did when I bought it, but the box doesn't say it does and I dont want to open it in case I have to return it.

    If the Belkin supports the A2DP (Stereo Bluetooth) profile then it will work.

  • IPod Nano 7th Gen says "Unsupported. Accessory is not supported" when trying to charge / sync

    iPod Nano 7th Gen says "Unsupported. Accessory is not supported" when trying to charge / sync with official apple lightening cable.
    It worked for almost a year then suddenly began to say that. My computer [windows], lightening cable and my power brick [all apple official] are all the same as they were when it was working. The iPod is almost a year old now, and has worked perfectly up until about a week ago.
    I have tried resetting the iPod, plugging it into different charging sources but it keeps saying "Unsupported. Accessory is not supported"
    Does anyone have any ideas on how to fix it?
    Thanks.

    Your iPod Nano firmware and iTunes updated to the current versions? 
    It is very difficult to offer troubleshooting suggestions when the "os version" you are using is unknown as each os has their own troubleshooting solutions. 

  • My ipod nano 7th gen no longer shows "Playlists" in the music menu. No changes made other than deleting one and adding one playlist to those synced. Synced fine in late February. Not working as of 3/7/2014.

    My ipod nano 7th gen no longer shows "Playlists" in the music menu. No changes made other than deleting one and adding one playlist to those synced. Synced fine in late February. Not working as of 3/7/2014.

    I would either say that the iOS is correpted due to a software glitch or y have have a hardware problem like bad memory locations that are corrupting the iOS.
    - Restore from backup via iTunes. This will install a fresh copy of the iOS. See:                                                
    iOS: How to back up                                                                                     
    - Restore to factory settings/new iOS device.   This will elimate corruptin in the backup causing the problem.          
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • IPod Nano 7th Gen. & Nike App

    Good morning friends,
    I am interested in purchasing an iPod Nano 7th Gen. for the fitness app but I have some queries - I've checked online and am a little more confused then when I started.
    I understand that the Nike Fitness App doesn't need the shoe sensor in order to work.  This is the main reason I am interested in purchasing the product; however, in the store the personnel indicated that the shoe sensor is required.  I investigated this a little and now I am of the understanding that you can use the app without the shoe sensor for walking/running, but that having said sensor makes the app more efficient/accurate.
    Could someone clarify this for me, and indicate which are the functions when having the iPod only or having the iPod + shoe sensor?
    Thanks so much in advance!

    Hello,
    I have the ipod nano 7th gen. I use it without the sensor and it works fine. It is quite accurate. I have tested it by running around my neighborhood and then compared my run  to Google Maps and it was pretty close. After each run, you can calibrate your distance. This will make your runs even more accurate.

Maybe you are looking for

  • Creation of a Dimension by ODI

    I can help with the creation of an OLAP dimension with Oracle Data Integrator. And what knowledge modules are used I appreciate any guidance and help on this topic. Thanks in advance

  • PI-7.0(xi-7.0) as production server - wrongly abap client(001)

    Hi all, We are using PI-7.0(xi-7.0) as production server, we ran the post installtion successfuly  last  6month before and now server status is live production system. Our issue is we ran wrongly abap client(001)as default client in the  post-install

  • Rounding up values in Print Layout Designer

    The customer has a database field in print layout designer and this is bringing back a value such as 0.25.  They would like to create another field which shows this value rounded up to the nearest whole number, ie in the case of 0.25 they would like

  • QuickLook and preview pane stretches images

    The Finder column view preview pane and QuickLook stretch many of my photos. But when I open the same photos in Preview.app, they look normal. Screenshot: For example, download this image (reaver.jpg), and view it with Finder's column view. Now view

  • Port Foward Vs. DMZ

    My company is in the process of implementing a new system that they want internal and external access to. I would like to use our DMZ, however there is a concern that we will overrun the throughput of our PIX 525. The software vendor just wants us to