My iPod Nano 7th is not recognized by my ASUS 11.6 mini PC with Windows 8 and IE 10.  Any suggestions?  Thanks.  Lily

My iPod Nano 7th is not recognized by Windows 8 in my ASUS 11.6 mini PC with IE 10.  Any suggestions? Thanks.  Brownalex

Hey Brownalex,
I'd follow the steps in this article if your iPod nano doesn't appear in iTunes and also doesn't appear as a disk drive in My Computer:
iPod not recognized in 'My Computer' and in iTunes for Windows
http://support.apple.com/kb/TS1369
Hope that helps,
David

Similar Messages

  • After upgrade to Windows 8.1, ipod nano 7th gen not recognized

    /after upgrading to Windows 8.1, ITunes does not recognize my ipod nano 7th gen.  I have uninstalled and reinstalled ITunes but no luck.  I have gone through all steps in troubleshooting, but it still doesn't recognize it.  Help!

    Hi cindywindy,
    If your iPod Nano is no longer recognized in iTunes after a recent system upgrade, you may find the following article helpful (apologies if you have already seen it):
    Apple Support: iPod not recognized in My Computer and in iTunes for Windows
    http://support.apple.com/kb/ts1369
    Regards,
    - Brenden

  • Ipod Nano 7th generation not recognized by computer or iTunes

    Neither my computer nor ITunes recognizes my Ipod nano 7th generation. It was working fine until I ran an intensive AVG PC tuneup on the laptop. Device manager recognizes the Ipod and says it is working correctly. I have done all suggested troubleshooting and nothing has yet worked. Additional suggestions or info I should provide?

    diagnostic shows....
    **** Device Connectivity Tests ****
    iPodService 11.3.1.2 (x64) is currently running.
    iTunesHelper 11.3.1.2 is currently running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    Universal Serial Bus Controllers:
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC. Device is working properly.
    No FireWire (IEEE 1394) Host Controller found.
    Most Recent Devices Not Currently Connected:
    iPod nano (4th Generation) running firmware version 1.0.4
    Serial Number:       Y(I removed info)
    **** Device Sync Tests ****
    No iPod, iPhone, or iPad found.
    it looks like everything is fine, except it can't find the ipod... why?
    when I plug in a thumb drive, it recognizes that, why not the ipod?

  • Ipod nano 7th gen not recognized by iTunes. Windows

    My ipod was working fine until a couple months ago. Now whenever I hook up the ipod to the computer I get an error message saying an ipod has been detected, but it could not be identified properly. I've tried restarting the computer, deinstalling & reinstalling new iTunes, but to no avail. Help!

    In same boat. Mine wont even charge. Now fully dead. I have a number of different USB sources. Ipod doesn't recognize it is plug in.
    Ever since I got ipod has been detected, but it could not be identified properly.
    But trying to solve my problem Found most people solved there issue with holding on/off and sleep buttons at same time for few seconds to reboot. Didn't work for me.
    Might for you.

  • Ipod nano 7th gen not recognized by itunes

    how is this fixed

    This came from another thread, but worked for me.  Problem is with newest iTunes 4.62 and Windows 8.1.  Unistall iTunes, as well as its helper programs (Apple Application Support, Apple Mobile Divice Support, and Apple Software Update).  Reboot, and reinstall iTunes.  It will reinstall all the other ones and you should be able to connect your nano.  Good luck.

  • IPod Nano 7th Generation Not Being Recognized?

    I've downloaded the latest version of iTunes 11 which is titled, "iTunes 11.0.1," last night and it hasn't been recognizing my iPod Nano 7th Generation. Anybody having this problem?

    Did it work with the previous version of iTunes?

  • IPod Nano 7th Generation not charging

    Has anyone had trouble with their iPod Nano 7th Generation not charging?

    Hi ncpower,
    If you are having issues charging your iPod Nano, you may find the following article helpful:
    Apple Support: Charging your iPod battery
    http://support.apple.com/kb/ht1384
    Regards,
    - Brenden

  • How do I get the ipod nano 7th generation to only show the album artwork? the volume control, info bar and album artwork shows whenever a song is playing.

    How do I get the ipod nano 7th generation to only show the album artwork? the volume control, info bar and album artwork shows whenever a song is playing.

    Hi TheGuru146,
    It sounds like the iPod isn't restoring correctly. Try putting the it into Disk Mode manually and then restoring the iPod again as described in the article linked below.
    Putting iPod into Disk Mode
    http://support.apple.com/kb/ht1363
    iPod nano (7th generation)
    Before placing the iPod into Disk Mode, verify that it has a charge.
    Reset the device by pressing the Sleep and Home buttons simultaneously until the display shows the Apple logo. This should take about eight seconds.
    When the Apple logo appears, press and hold the Volume Down and Volume Up buttons simultaneously until the device enters Disk Mode.
    -Jason

  • My ipod nano 6th gen screen is white ive tried the hard disk mode with the power and volume buttons and it still wont work any suggestions?

    my ipod nano 6th gen screen is white ive tried the hard disk mode with the power and volume buttons and it still wont work any suggestions?

    You can try Restoring it in iTunes but I believe you will end up needing to have it serviced.

  • IPod Nano 7th gen not turning on but recognized by iTunes and Windows

    My two-month old 7th gen iPod Nano is not turning on. I've reset and restored it using both Windows (My Computer) and iTunes and have downloaded the and installed the latest version of iTunes. It was working fine and now just will not turn on. It is being recognized by Windows as a removable disc and by iTunes as an iPod that I can sync data onto.
    I've tried the 'hold the power button for 5 seconds' trick to try to manually reset it, as well as other variations with pressing down on the power and menu keys simultaneously. The iPod is new, ordered online and the nearest Apple Store is over 2 hours away from where I live.
    Please help?

    Hello, M.Ram.  
    Thank you for visiting Apple Support Communities.  
    I understand that the screen on your iPod nano is black, but is recognized by iTunes.  Take a look at the troubleshooting article below as it may provide some troubleshooting steps that may help.  However, if the issue persists, see the section labeled Issue not resolved.  
    iPod nano (7th generation): Hardware troubleshooting
    -Jason H.  

  • IPod Nano 7th gen not syncing, accesoire not recognized

    Hello,
    My iPod Nano 7th generation is not syncing to my Macbook Pro, late 2011 and my iPod says 'Accesoire not recognized', while it's a lightning-cable from Apple itself. Can anyone help?

    Hello, Bram66. 
    Thank you for visiting Apple Support Communities. 
    I would recommend making sure you are using an Apple branded Lightning to USB cable, the MacBook Pro is connected to power and that you are not using a USB hub or docking station when charging the iPod nano.  If you are still experiencing issues after making the above changes, see the troubleshooting steps in the article below. 
    iPod nano (7th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS4433
    Cheers,
    Jason H. 

  • Ipod nano 7th gen not being recognized by itunes

    i have the new hp split x2 laptop running windows 8. i kept ignoring the new itunes update and everything was fine but as soon as i installed it, itunes no longer recognized my ipod nano (7th gen). i have been sitting here for about 2 hours looking for answers so now i am asking for them instead. is there a way to uninstall the last update? i would go to best buy and just have geek squad fix it for free (because im covered for 2 years) but we are currently having a massive snow storm here in NY please help!

    I'm trying to put songs on it

  • Ipod Nano 7th Generation - Not Charging / Error Msg From Comp 'Attached Device Malfunctioned'

    My IPod Nano 7th gen arrived last night.  I was able to turn it on and select language 'english'  When I connected it to my computer it did not recognize my iPod, so it also did not show up in iTunes,  Error message: "One of the USB devices attached to this computer has malfunctioned.  and Windows does not recognize it." 
    My Nano turned off and went blank.   I have tried to reset it.  Nothing works, just blank.
    No charge icon, I have tried all USB ports on my comp, but nothing works- (but my USB ports work fine)  I have read that if my iPod has not been charged fully, the computer my not recognize it.
    I am now using an adapter and trying to charge it thru the wall power socket.  It has been connected for half an hour.  Still cannot turn iPod on.
    I have Windows 7 running on comp.  Itunes is current version 10.7.  I have rebooted my comp several times and re-installed iTunes.
    I have an iPhone and an iPod shuffle that are both synced with iTunes on this comp, they work fine.
    Is my iPod broken?  Do I send it back?  Anyone else having the same problems?  Please Help !!

    I had this problem as well.  I have a PC running Windows 7. I have installed the latest iTunes 10.7 software (64 bit). I reset the nano by holding down the start and home button for 10 seconds.  Then - I plugged it into a PC running Windows XP and was able to format the iPod. Ejected it and plugged it into my Windows 7 computer and then the computer recognized it and I was able to load it. There is some problem with iTunes 7 on Windows 7.

  • IPod nano 7th gen not found in iTunes/"no disc in drive" Windows computer.

    I bought a brand new iPod nano 7th generation yesterday. When I plugged it into my Windows computer it began set up then stopped and a pop up appeared ''no disc in drive'' directly after that the next pop up read ''iPod cannot sync because it was not found''. My iPod is charging the entire time until that second pop up appears and then my iTunes acts as if the device was unplugged from the computer, it stops charging and at the top of my iTunes screen it says "OK to disconnect". I tried putting my iPod into "disk mode" but the same two pop ups still come up and the same thing happens. And even though iTunes recognizes the iPod as being unplugged even before it is, even after I do unplug it my computer still thinks it's attached, down in my tool bar it's still there waiting to be disconnected. As soon as iTunes begins starting up with my iPod it says there's no disc and then that the iPod can't be found even though it's still plugged in. I can't get any music on it let alone get my computer to recognize it for longer than 30 seconds. I really don't want to return it because my iPhone4 is full and can't fit any more music so I needed this iPod.

    Hello Abbey,
    I would recommend the steps in this article named iOS: Device not recognized in iTunes for Windows found here http://support.apple.com/kb/TS1538. While the title of the article describes a symptom a bit different from yours, I feel the troubleshooting is still relevant.
    If that does not resolve the issue, then I would suggest this article to help troubleshoot the USB connection.
    iOS: Troubleshooting USB connection
    http://support.apple.com/kb/ts1286
    And lastly, resetting it just may do the trick.
    How to reset an iPod nano (7th generation)
    Press and hold the Sleep/Wake button and the Home button until the screen goes dark. The Apple logo should appear after a few seconds, then the Home screen should appear.
    From: How to reset iPod
              http://support.apple.com/kb/ht1320
    Take care,
    Sterling

  • IPod nano 7th gen not recognised in iTunes using Windows 8.1

    I have an older 3rd generation iPod nano and a new 7th gen nano and I would like to sync them to the same iTunes on my Dell laptop (Inspiron 7520) running Win8.1. I have also updated iTunes to the latest version.
    When I connect the new 7th gen iPod nano to my laptop via USB (tried all 4 ports)  I get the following error message from iTunes:
    "An iPod has been detected, but it could not be identified properly. Please disconnect and reconnect the iPod, then try again."
    I've been through most of http://support.apple.com/kb/TS3218  and still get the error message although I haven't tried connecting the iPad nano 7th gen to an older Win7 laptop yet with a fresh iTunes install.
    When connecting the iPod nano7 Win8.1 recognises E: as an iPod very briefly after I have run a scan via McAfee. After a few seconds the E: drive disappears and iTunes reports the error message as above.  Sometimes, E: doesn't disappear in Win8.1 but I still get the iTunes error message and the iPod nano itself goes from Connected to Main menu.
    Any ideas how I can get iTunes to recognise my 7th gen nano?  I'm not sure if this is a Win8.1 problem or iTunes.

    Hello Abbey,
    I would recommend the steps in this article named iOS: Device not recognized in iTunes for Windows found here http://support.apple.com/kb/TS1538. While the title of the article describes a symptom a bit different from yours, I feel the troubleshooting is still relevant.
    If that does not resolve the issue, then I would suggest this article to help troubleshoot the USB connection.
    iOS: Troubleshooting USB connection
    http://support.apple.com/kb/ts1286
    And lastly, resetting it just may do the trick.
    How to reset an iPod nano (7th generation)
    Press and hold the Sleep/Wake button and the Home button until the screen goes dark. The Apple logo should appear after a few seconds, then the Home screen should appear.
    From: How to reset iPod
              http://support.apple.com/kb/ht1320
    Take care,
    Sterling

Maybe you are looking for

  • Loading some records into Custom-R/3 table manually

    Hai I created one custom R/3 table. One of my friend load some records into that cutom table manaully. I want to load some more records manually. So how can i load some records into the custom R/3 Table manully . Please let me know i ll assing the po

  • How to get satisfaction from Verizon.

    By now a few of you, very few actually have figured it out how to get from Verizon what you felt was satisfactory. In some cases like mine my wife and I exchanged our defective new Fascinates for brand new working Fascinates. Some of you prefer a dif

  • IWeb and photo corrections and importing photos

    Yeah, another iWeb problem. I both love and hate the application. I hadn't had this problem before now. I imported many, many photos into albums (via Aperture...) before noticing that the photos in download mode on my website were showing up at half

  • How do I renew my membership

    Hello, so my membership is about to finish i searched everywhere in how to renew it but it's too complicated, please help before it expires i need it. Thank you.

  • Getting SIM to connect in IdeaPad

    We are finalists today in the AT&T competition for "Best Mobile App" in Open category.  We present the App to judges using IdeaPad S10-3t connected using a Sierra Lightning USB device. We would like to put the SIM inside the IdeaPad for the final jud