My iPod shuts down after 30 minutes. Won't turn on until plugged into dock.

My iPod plays for about 30 minutes and then shuts down.  It won't come back on until I either plug it into my computer or my iHome dock. I've tried resetting and syncing it.  Help! 

You might have a bad battery. But first try recalibrating the battery gauge. Run the battery all the way down until the phone shuts off and doesn't restart. Then charge for 4 hours with the wall charger. Repeat the process. If the problem remains you need a new battery.

Similar Messages

  • Tour shuts down after a period of time have to plug into charger for reboot

    Today I noticed that my phone will shut off after a little while of inactivity.  The battery will be mostly full, and it thinks it dies.  So inorder to reboot you must plug it into the charger.  Once you plug it into the charger you get the image of the battery with a bolt in the middle of the screen.  After a few minutes of charging it resets to the home screen, and after another period of time it will do it again.  You might think this is occurring because the battery is dead but the battery will be 50% maybe a little more or a little less.  I am wondering if this is an OS problem or something that is just wrong with my phone...

    That definitely sounds like a phone issue.  We had a user with a similar problem that ended up getting her phone replaced.  She hasn't had any issues since. 

  • IPod classic won't turn off when plugged into a home theater dock; what's up? will it hurt to leave it on all the time?

    I bought a new iPod Classic and it won't turn off when plugged into a home theater dock. Is this normal and will it hurt the iPod if i leave it on all the time?

    Hi there,
    How old is your Classic? Often, after a couple of years, rechargable batteries begin to fail, especially after such a long period of inactivity. This happens with any gadget with this type of battery.
    Try leaving it plugged in for 24 hours, and try again, to rule out that it isn't just really low on charge. If this doesn't help, it may be a good time to buy a replacement. New iPod Nanos and Touches will be released this October.
    Below, I've linked to an Apple website which explains rechargable batteries, and why yours may not be working.
    Apple - Batteries
    I hope this helps, and I hope upgrading your device will not feel like an unnecessary expense. Let me know if you have any more questions,
    Nathan

  • IPod shuts down after playing music for 1 minute

    Whenever I try to listen to music or radio the device shuts down after exactly 1 minute. Can't find a setting to change this. I already did reset all settings, to no avail. Any help? Thanks!

    Make sure the headphones are plugged all the way in, meaning no silver from the headphone's plug can still be seen.  You shoul hear a sort of clicking noise when inserted the headphones to signal that they have been fully seated.
    B-rock

  • What do I do if an iPod shuts down after going into sleep mode

    My friends iPod keeps shutting down after it goes into sleep mode. I just fixed it up (restored it, had to dry it out after it fell into water) and now it does that. Everything else works fine but if I put it in sleep mode or put it into sleep mode it shuts down. How do I fix this because I've never seen this happen before.

    Hey Tecmo_SB_Guy, 
    I would suggest you take a look at advanced power settings. It can seem like the notebook is turning off when it is actually just hibernating. You can set it to not hibernate. 
    1. Windows key + Q to open the Search Bar
    2. Type "power" 
    3. Click Settings under the Search Bar
    4. Select Power Options from the results on the left. 
    5. In Power Options, Click Change when the computer sleeps, on the left. 
    6. Set the Put the computer to sleep setting so that it fits your usage best. 
    7. Click Change advanced power settings, at the bottom.
    8. Expand Sleep and expand Hibernate after. If you want you can change the hibernation setting to Never by typing "Never" into the minutes field. See attached picture. You can do this for battery and/or plugged in.
    9. Click Apply to save changes.
    If you don't already shut it down periodically, I would suggest shutting it down at least 2-3 times a week if you use it daily. Leaving the computer running continuously can shorten its lifespan. Hard drive failures and motherboard issues are seen much more often on machines that are left running constantly. Computers get bogged down and run slowly when the memory is full. Memory only clears out and resets itself when the computer is shut down. Here is a link explaining more about memory accumulation and hardware aging.
    I hope these suggestions help! Please let me know if you have any questions
    Attachments:
    PowerHibernateNever.jpg ‏59 KB

  • Ipod Shuts down after song

    Hello all,
    I got an iPod Nano 3d Gen for my birthday 2 months ago.
    I uploaded songs on it, and a video or two.
    I everything was fine untill one day the iPod had shutdown after a song.
    First I thought it was just something that'd happen once, So I restarted it and selected a song.
    But again, the iPod would shutdown after the song was done.
    After that my iPod has not been working like it should be, always shutting down after a song was finished.
    I followed the 5 steps to fix most problems (Restart, Reboot etc)
    But the problem with that was that my computer did not see the iPod.
    My iPod would say it was connected for about 2 seconds, and then it would shut down again.
    The Computer Management window couldn't see it either.
    I tried almost everything I think, and nothing worked.
    So my question is this,
    Does anyone have the same problem?
    Or does anyone how to fix an iPod with these problems?

    Your nano is pausing playback when the screen goes dark (Either when it goes dark on its own or when you click the sleep/wake button). The reason for this is that it is not detecting your headset. You may be able to hear music, but the headset jack is not inserted enough for the nano to detect that it is there (or something is blocking the connection). Here are your three options:
    Insert the headset jack harder. Most folks find that this solves their problem. If you can see ANY of the silver of the plug when it is inserted, it is NOT fully inserted. You should feel and hear a click" when it is fully inserted.
    Clean out the crud in the headset port. If you have tried #1 and it just won't insert all the way, it is likely that you have crud in your headset jack. Shine a light in there. The entire inside of the jack is white, so if it looks dark down at the bottom, there is probably crud down there. You can try blowing it out or using canned air. Just understand that shoving anything else in there to clean it out will be taking your warranty into your own hands! However, I have cleaned mine out using whatever was handy and small enough to fit in there and so far so good. Your results may vary!
    Take it to the Apple store. If you have really tried with 1 and 2 and it is still happening, then there might just be something up with your headset port or your headset jack. If it is the headset jack, you can look closely at that and be pretty sure if that is the problem. Try another headset to make sure. If you have worked all the way through to this point and it is still happening, it is time to take it to the Apple store.
    i

  • Premier shuts down after minutes

    A couple of days ago my premier pro unexpectedly started shuting down after minutes of editing. I've had it for a while now and nothing like this has ever happened. I already reinstalled it tried opening new projects but it keeps happening. The odd thing is that it doesn't happen with old projects, only those I started a couple days ago. Maybe it's because of an

    Hi,
    Please provide the following details:
    OS
    Memory
    Processor
    Graphics Card
    Exact version of Premiere Pro
    Can you attach screenshot of the error?
    Thanks,
    Rameez

  • IPOD shuts down after restore

    Renamed the IPod. Used restore feature. Now it won't hold settings and keeps shutting down. Could it be battery?

    I had the same problem...
    Returned it to the apple store and I never updated to the new 1.0.2 version... my iPod classic now works perfectly fine.
    Advice is to return it and get a replacement.

  • IPod shuts down after white screen

    I just replaced my 5G's screen (original was cracked), but after starting up, the screen is immediately all white (apple logo or menu never shows up) for a couple of seconds, I hear the HD, and then it shuts down. I can not reset using apple's method as it just keeps restarting the same way with the white screen?
    Anyone have an idea of what could have gone wrong with my screen update? The instructions were pretty straight forward, and I followed them carefully.

    i believe that i damaged the connector somehow (no idea how), and have sent it in to get the logic board replaced.

  • Shuts down after sleep, won't start up

    I've got what sounds like a common problem with my just-purchased iBook---it shut down at some point last night in sleep mode, and won't start back up. Of course, I disconnected everything but the power supply before attempting to start up, but to no avail.
    I read in another thread that removing the battery, then immediately replacing it, seems to help some folks. I'll try that next. Failing that, what should I try next?
    Any ideas greatly appreciated!

    Sam,
    This has happened once to my wife's iBook.
    I fixed it by resetting the PRAM, as suggested by a very helpful Apple Tech. person:
    1. Shut down the computer.
    2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    3. Turn on the computer.
    4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    6. Release the keys.
    Your computer's PRAM and the NVRAM are reset to the default values. The clock settings may be reset to a default date on some models.
    Paul

  • I downloaded silverlight to watch netflix but then my mac shut down suddenly and won't turn back on. How do i get it to turn on?

    It's a brand new laptop and when i downloaded silverlight to stream netflix, it worked for like half an hour and then my computer just shuts down. i turn it on again and delete silverlight but a couple minutes later it shuts down again and this time it won't turn back on.

    If it won't bong, then try an SMC reset.
    http://support.apple.com/kb/HT3964
    Can you boot in Safe Mode?
    http://support.apple.com/kb/HT1564
    Did you uninstall it this way?
    http://www.microsoft.com/getsilverlight/get-started/install/removing-silverlight -mac.aspx

  • MacBook Pro (retina late-2013) randomly shut down and now won't turn on again

    My first submission on here
    I recently bought a MBPR a few days ago and was working seamlessly. Today I had taken it off charge to watch a couple videos and talk to a few people online. While I was doing this, the MacBook Pro was rested on a couch so I'm certain ventellation was fine.
    Then at one point it shut down unexpectedly. I was able to turn if back on, thinking it might be battery but as it booted back up I saw that it was on 65%. I then continued to use it and by the time it reach ~60% it shut down again. This time I wasn't able to boot it up again at all. I pressed the pwer button, plugged it into power and pressed it again and even tried an SMC reset. The AC's indicator LED flashed from orange to green (as it is suppoed to with SMC resets) but it would still not turn on after I pressed the power button again.
    Please help, this computer is brand new and I am not sure what could have caused this.
    Thank you

    I have picked up my brand new MBPR on the 4th as well, and last night restarted for the first time after software update ( mavericks ) and after 3 hours hours of grey screen with spinning wheel called APPLE who again never knows what they are talking about because they keep saying " we never heard about that " when I called about the same issue on my 17 inch 2 months ago. So I called 3 times this morning and when I let them know that I am quite " puzzled " that every time I mention a Maverick Issue suddensly my call gets disconnected, and nobody calls me back when THEY SWEAR they took notes of my call bacl number. Last call a few minutes ago, I spoke to a supervisor and talked for 45 minutes about all issues and when he expressed concern about me recording the call I told him " You guys record my calls, so where does it say where I couldn't record yours if I wanted to ? " and the supervisor hung up on me... Way to Go APPLE!!! I've been an apple devotee since I first got my apple lisa in 1984 but they have only been going to " s*** " the last 2-3 years.
    So DIGGLY, do like I will this morning and return your purchase!

  • HT1430 The iPad froze while reading.  I couldn't close the app or shut down.  Eventually it shut down but now won't turn on.  I recharged recently so it is not the battery

    My iPad screen is black and it won't power up.  It froze while reading this morning.  I couldn't close the app, turn off or power down.  The screen eventually turned off.  I recently recharged the battery so that isn't the issue.  I have held power button down to no avail.  What should I do?

    Press and hold both the home and power buttons till the Apple logo appears. Release both buttons. Wait till your iPad starts on it's own.

  • IPod very low on battery and now won't turn on when plugged into PC

    I haven't used my iPod for a few weeks, so now the battery is obviously completely empty. The problem is that it won't turn on when I plug it into my PC to charge, even after half an hour or longer. Is there something I can do, or do I need to get a completely new battery put in?
    iPod nano    

    If you are unable to give specifics about the problem or what you need to do, it's going to be rather hard to give you recommendations or alternate suggestions.
    As I said, if I recall correctly, the iPod will stay on if it's being charged. But, in case I'm misremembering, are you holding down the button until you see the red arrow that says "Slide to power off"? Have you tried restoring it?

  • IPod Classic won't turn on unless plugged into wall even though battery is charged

    I plugged in my old iPod Classic and charged it up for a long time. I got that little plug symbol that indicates that it's fully charged. The iPod turns on and works fine when it's plugged into the wall, but as soon as I unplug it, it won't do anything at all. Just black screen. I also tried plugging it into the computer. Nothing.
    I tried re-setting by toggling the "Hold" button and then pressing Play/Pause and Menu at the same time. Nothing.
    Why would it be fine when plugged into the wall but not when unplugged or plugged into the computer? Is it possible that is really is not fully charged even though it did show that little plug symbol? It had been just sitting for many months.

    Hi there,
    How old is your Classic? Often, after a couple of years, rechargable batteries begin to fail, especially after such a long period of inactivity. This happens with any gadget with this type of battery.
    Try leaving it plugged in for 24 hours, and try again, to rule out that it isn't just really low on charge. If this doesn't help, it may be a good time to buy a replacement. New iPod Nanos and Touches will be released this October.
    Below, I've linked to an Apple website which explains rechargable batteries, and why yours may not be working.
    Apple - Batteries
    I hope this helps, and I hope upgrading your device will not feel like an unnecessary expense. Let me know if you have any more questions,
    Nathan

Maybe you are looking for

  • How to send message from multiline container to same webservice or bus. sys

    Hi All, I want to send message from multiline container to a syn web service sequentially. I am getting that multiline container after a transformations step (1: n mapping). where i dont known what will be the value for n (number of message in multil

  • Printing and email script/button

    I have a form that will be deployed out to employee's laptops that they will use to generate a quote to customers. I need a button that will print the said form as a static pdf document (none of the controls are active that can change the price) and

  • Can I convert many XMLs into one Excel Sheet?

    Hi: I get 20-30 XMLs daily from client and I want them all converted and merged in single excel sheet through AppleScript. Can any one help? Thank you.

  • Mac Mini shuts down without warning, doesn't want to re-boot again

    My mini is only 3 months old. I upgraded to 2 gigs of Ram when I got it (saved about a hundred bucks). It seems to be overheating and shutting down, problem is it happens all the time. When I try to restart it, I must wait until it is cold to the tou

  • Need serial number #2

    I know I need to contact Apple but my question is who and how? Telephone, email what?