My iPod touch 4g keeps going to lockscreen and back to the apple logo and I can't shut it off or anything
My iPod touch 4g keeps going to lock screen and back to apple logo over and over and I can't turn it off or anything
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Similar Messages
-
Can someone please help with my issue listed - My ipod 4G wont go past the apple logo when I turn it on - it will stay on the apple logo for few min, then blanks out and back to the apple logo. Tried reset option/troubleshoot several times. Also wont show up on computer at all when I plug in to USB.
Any tips are very much appreciated.Place the iPod Touch into DFU mode. This will be similar to what the factory would do to install the iOS onto new iOS devices.
Placing it into DFU mode will allow you to "format" and install the current iOS for that device.
To place your iOS device into DFU mode.
First connect you iOS device to you computer.
Open iTunes if not already open
Now turn off your iOS device using the power swipe.
Press the home and sleep button on your iOS device for 10 seconds.
Release the sleep button but carry on holding down the home button. For another 10 seconds.
Your iOS device should now be on DFU. Click on restore and iTunes will download the latest iOS for your device.
Hopefully that sorts it if not, you will have to go to a service centre or call Apple Care up and get them to collect it and repair it. (replace it) Or go into an Apple Store. -
hi my iphone was fully charged and turned its self off, i have tried to turn it back on and reset it, but no luck so i have plugged it in to my pc and it displays the apple logo and then goes back off i have tried this a number of times with no success anyone got any idears?
Try here:
iOS: Not responding or does not turn on -
My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected
If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages. -
Ipod has shut off and only shows the apple logo and the loading screen for the past day
I was downloading a song from one of the ipod apps for illegal songs and it just stoped downloading so i restarted my ipod and it would turn back on but if i would try to go back into the app it would only push me out of it. so after restarting it a coupld more times just with the ipod it has resulted in not turning back on and remaining on the apple logo screen then to the loading screen. it wont turn on at all. i have charged it (or tried) for a whole night but the whole night it has remained on the two screen. i cant plus it into my computer because then i will lose all my music. i dont know what to do.?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
You will very very likely lose the contents on the iPod. That is the way it is . -
Tried to update iPod Touch to iOS 5, now it's frozen with the Apple logo
Got an error message (Unknown error) on the PC, iPod is stuck with the apple symbol and the spinning circle in the middle (data downlod)
Try a manual install (using DFU Mode), as outlined in the link below.
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro 8G RAM 750G HD + OCZ Vertex 3 SSD Boot HD
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
In Memory of Steve Jobs -
My macbook will not boot. It goes to a blue screen after the logo and wheel goes off. I have taken the battery out and held the on/off button for five seconds and reset the PRAM. I have the the original os disk but have not put it in for fear of losing un backed op data.
Thanks
RichYou won't lose any data unless you erase your hard drive.
Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c"key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it.When it comes up is your Hard Drive in the list on the left?
If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've selected the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions. -
My Ipod 5th generation, which I bought a week ago, I noticed I had a scratch on the back logo and one on the bottom and I never remembered ever scratching it. Is there any possible way where it could be fixed?
You could pay for a replacement at the repair price:
Apple - Support - iPod - Repair pricing -
My ipod touch keeps turning off and on. The apple logo appears a while then it turn off and on again
I tried to put it on recovery mode but it doesnt work either. Before that, I tried to reset it using the reset options in the settings. Please reply as soon as possible
See here for troubleshooting iOS:
https://sites.google.com/site/appleclubfhs/support/advice-and-articles/troublesh ooting-ios
(Skip the Restart step since you cannot access the red slider bar)
(Note that my links to other pages may promote my organization, and this should not be taken as an endorsement by Apple) -
Why can't I just restore it under a new account or something liked that? What else can I try in order to restore it I have tried everything even under her itunes acct and all. Please help!
I don't know what operating system out has my computer first see it when itunes does.Sounds like the iPhone is damaged beyond repair.
Out of Warranty replacement in the US is $199. -
my 5th generation ipod froze and stold on the apple logo and every time i press the home buttom or the power buttom it just takes me back to the apple logo
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Ipod nano 4th generation switches between the Apple logo and the menu
I have a 4th generation 8 g iPod Nano that probably has about 1 hour of use since my wife won it in a raffle over a year ago. When I went to recharge it yesterday, the only thing that happens is that the display, when connected to the computer, flips back and forth between the Apple logo and the menu screen. Whenever either one of them appears, it will disappear in a few seconds, then repeat the sequence. I have done a reset and restore,and installed the latest software version but the same thing happens over and over again. If the iPod is detached from the computer, ie, its power source, NOTHING happens on the display. It black and you can't get it to show anything. My theory was that the battery needed to be replaced even though it wasn't used much in the year since she got it. In fact. the absence of use and recharging it and discharging it may have lead to this problem in the first place. However, my one issue with that theory is that, when connected to a power source, like the computer, I would think I could get it to function normally, which I can't. I was able to get to the "service menu" which won't disappear when I move about different choices, as long as its connected to the computer. Again I can get nothing if its not connected to a power source.. does anyone think that this problem could be solved by replacing the battery or does it seem like that is only part of the problem? Thanks for any help and suggestions you may have to offer.
GeoffDespite the Nano only being used for an hour or so, the battery needed to be replaced= problem solved!!
-
My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?
Please help me out as this is very irritating. This has been happening for the last 20-30 minutes. It had roughly half battery left.Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
my ipod keeps going on & off showing the battery & then back to the apple nothing else what can i d
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
maybe here too:
- See:
iPod touch: Hardware troubleshooting
- Try another cable
- Try another charging source
- Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, cracked or broken plastic.
- Make an appointment at the Genus Bar of an Apple store.
Apple Retail Store - Genius Bar -
my ipod touch is stuck on the apple logo and after a while a white screen comes up and it restarts and the same thing all over agan. this happened to me before and after a while it turns on but why does it keep on doing this?
Try connecting the iPod Touch to your computer and restore it. http://support.apple.com/kb/HT1414
Maybe you are looking for
-
How can I encrypt my data uplinks between switch trunk ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me as I want to encrypt my switch-to-switch link with Cisco TrustSec.
-
Horizontal Scrolling Thumbnails Slideshow (Are these possible in Muse CC 2014)
Good afternoon Muse Forum: My name is Ira Bitner from NYC U.S.A. How are you? I have a question regarding slideshow and thumbnails in MUSE CC 2014. Q: In Muse is it possible to have a Slideshow with Scrolling Horizontal Thumbnails? In other words is
-
Hello, Our requirement: The reporting solution will use the profit center hierarchy-1 for reporting data by profit center. Financial data(extracted from other system) will be assigned to profit centers in the hierarchy-2. The only difference betwee
-
Is there a way to modify the adjustment brick default values in Aperture 3? For example, in the Edge Sharpen brick, the default values shown in my copy of Aperture are: Intensity .81, Edges .22, Falloff .69. I've made a preset that modifies these def
-
CRM Questionnaire Results Edit In-House Repair Fields
I am new to CRM and I want to make the results of a questionnaire automatically edit the fields of an in-house repair on the WebGUI in SAP CRM 7.0. After looking into this issue I think I have to work with the BADI CRM_MKTCA_SVY_PAI and the IMG path