My ipod touch needed to be updated so I did and now it won't turn on all it does is show the itunes icon and says toconnect it to itunes so I did and let it be updated and now it wont turn on and I tried resetting but nothing changed.
My ipod touch needed to be updated so I did and now it won't turn on all it does is show the itunes icon and says toconnect it to itunes so I did and let it be updated and now it wont turn on and I tried resetting but nothing changed.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Similar Messages
-
I updated my iPhone today over wifi. It downloaded 6.1.3 completely and started then installed it. After the install all it does is show the connect to iTunes screen. What did I do wrong and now do I have to completely restore the phone?
Next question.... I did an iCloud save point earlier today so in theory everything should have been saved and the restore won't be a complete loss right? Please tell me my pics aren't gone.....
Thanks for the help. -
Hi, I recently discovered my ipod touch would no longer turn on. I've tried everything! All it does is show the low battery sign, and that is if it's connected to a computer. No matter how long I leave it charging, it does that. Is there a way to fix it? All I want are my contacts and my old calendar back. These did not sync with iTunes like my photos, music, and video. I can probably get an older, replacement iPod, but I don't want to have to readd all my important dates and reminders, as well as contact information. I guess I have two questions:
1) is there a way to get my ipod to start working again?
2) is there a way to get my old contacts and calendar back again?Try here:
iPod touch: Hardware troubleshooting
iOS: Not responding or does not turn on
To get the calender and contacts back if you can't get the iPod working is to restore the new iPod from the backup of the old one. -
My iPod Nano 6th generation fell one time and it kept working with a small crack in the screen.But after a while it just gave out and does not turn on.I try to charge it and all it does is blink the apple icon on and off.When disconnected nothing happens.
I am having the identical trouble as described above with my month old Macbook Air. I tried everything with the ditto results. Please help anyone!
Mine is a Macbook Air 13', 128GB, 1.86GHz with 4 GB RAM. -
my desktop is not working when i open it all it does is show the color weal and it never gos away on my mac book pro how do i fix it?
It means, tentatively, that system files are missing or damaged and you will have to reinstall Snow Leopard. See the following:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/. -
Everytime i try to open my itunes icon it says "This version of itunes has not been correctly localized for this language. Please run the English version". Then there is no option and i dont know to do this. Please help.
"This version of itunes has not been correctly localized for this language. Please run the English version".
Let's try a repair install of iTunes.
Restart the PC first.
If you're using Vista or 7, now head into your Uninstall a program control panel, select "iTunes" and then click "Repair".
If you're using XP, head into your Add or Remove Programs control panel, select "iTunes", and click "Change". Select "Repair" and click "Next" as per the following screenshot:
Can you launch your iTunes now? -
my iPad does not show the Airplay icon. The software is iOS 7.0.4, I have home sharing turned on and have an Apple TV. What should I do?
If you don't see the AirPlay icon in the Control Center:
1. Turn off router, Apple TV and iPad
2. Turn on router and then wait 30 seconds for it to complete start-up process
3. Turn on Apple TV and then wait 30 seconds for it to complete start-up process
4. Turn on iPad (wait 30 seconds) and test AirPlay -
my Ipad is not charging, it started after the battery died while i was playing a game, when i tried charging its only flashing the apple icon and it switches off again, help PLIIZ
Not charging
1. Reset iPad
2. Try another wall socket
3. Try another cable (make sure it's an original Apple cable)
4. Try another charger (make sure it's an original Apple charger)
5. Clean Lightning port with compress air or new paint brush -
My ipod wont charge, all it does is show the dead battery signal
I can't get my ipod touch to charge and it is out of warrenty where can i go to get it fixed or is there a simple soultion i can do do get it to work.
Not Charge
- See:
iPod touch: Hardware troubleshooting
iPhone and iPod touch: Charging the battery
- Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
- If a 5G iPod
Iphone 5 lightning port charging problem - SOLUTION!
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
Hi, My name is Cassie.
I bought my iPod off of amazon just around the end of January of this year (2012). Last night I was playing around on my iPod. Listening to pandora, and editing pictures. I got to a picture and clicked edit, and then my iPod shut off. It rebooted itself and seemed to be running as if nothing had happened. I put my music back on and went back to the picture and tried to edit it again. I clicked the edit button and the ipod shut off again. This time, it kept rebooting. It went to the apple symbol to turn on and about thirty seconds, the time it normally takes to turn on, the whole screen went white and then shut off and tried rebooting again. It kept doing this over and over again. After a while, it did eventually stop, but only to a completely white screen. It was like that all night long because I fell asleep. (gave up on it). It is now the afternoon and after I held the lock button and the home button down the screen when off. I let it sit for about a half an hour, then I tried turning it on again. But it still is doing the same thing. I have no idea what I could have done to make it do this. Unfortunalty, I am not home to connect it to my own iTunes, but regaurdless, it wont even connect to the computer. I did have my ipod plugged in the whole time it was rebooting and shutting off last night. It was connected to my wall jack which normally works fine. But even having it plugged into the computer as it is now, its still doing the same thing. I am dissapointed that I might end up loosing everything that I have on it. I have not been able to sync it to my computer to save all the apps and pictures and music I have stored on it. I really do hope I can get some help or advice!
Thank You!!
-Cassie LawrenceReset the PRAM
Reinstall the operating system from the dvd (you will not loose your data) -
My boyfriend bought a ipod nano 2nd generation and can't get it to work and it only shows apple icon and an ipod with a triangle next to it. Says to see apple.com/support/ipod. Can anyone help to figure out what we need to do to get this working. Thank you
I think it needs to be charged. Try keeping it connected to the computer for some time. Then disconnect and connect again. And I hope you have itunes installed in the PC as the iPod can be synced only with that. Here's the link to download itunes http://www.apple.com/itunes/
Also check the apple site for further syncing info. -
I updated the software for my iphone4s and now it won't work at all. I just get an apple icon
I updated my software on 4s iphone. Now my phone will not work. Just a black screen with and apple icon. Help please.
Put it in DFU mode and restore it. (google for instructions on entering DFU mode).
-
My computer restarted while I was updating software from OS4.1 to OS 5. Now my Ipod touch is just frozen. All it shows is the usb connection to itune symbol. Itune does not recognise. I have done the reset but nothing happens after the apple symbol shows up and back to usb and itune symbol. Help please.
See if placing the Ipod in recovery mode will allow iTunes to see the iPod so yu can restore the iPOd.. For recovery mode:
iPhone and iPod touch: Unable to update or restore
Next try DFU Mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
I just verified that i have an early 2011 Macbook Pro and the airplay icon does not appear. i also have a 2013 Macbook Pro which shows the airplay icon. do i need to enable airplay on my early 2011 or is there an update that is needed? Confused.
To check your model go to About This Mac (by clicking on the Apple icon, top left) and then select more info. If you wish to use mirroring you will need one from 2011 or later running OSX 10.8 or later. The alternative would be to use 3rd party software like Airparrot.
About AirPlay Mirroring in OS X -
My ipod touch has a black screen and will not turn on. i have charged my ipod and tryed troubleshooting but nothing seems to work. what can i do to have my ipod turn on again?
See Here...
Frozen or unresponsive iPod touch
Try this First... You will not lose any Data...
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
http://support.apple.com/kb/ht1430
Maybe you are looking for
-
Setting 1280x1024 Screen size in Jdeveloper 11.1.1.4 for development
Hi All, I am using JDeveloper 11.1.1.4 to develop an ADF application. I want to develop UI screens for lowest screen resolution as (1280x1024). But in the JDeveloper IDE in the resolution dropdown, I can only see the following Full screen 400x600 600
-
How do i update to snow leopard or yosemite from macintosh
How do i update to snow leopard or yosemite from macintosh
-
MSWord embedded in iFrame?
I hope that this question isn't repeated, I can't find the answer for my problem till now. The idea is that i need to launch a new word file in MSWord embeded in iFrame in html page, then after i allow the user to edit the file. i need to get a refer
-
Maintainence View not displaying contents
I have 2 custom tables one is zemployee and other is zdept. The foreign key is Dept No. I went to SE11 and created Maintaince View and done all the necessary steps like Relationships and View Fields. Finally I activated my view. Now when I click on C
-
Every time I import a clip into Final Cut Pro 7 I notice (upon opening the corresponding audio in the Viewer) that the clip is set to "-1" (for panning) as opposed to "0". It doesn't matter if it's material I shot with my own camera or downloaded sto