My iPod Touch's screan is frozen on a screan with the apple symbol on it

i tried updating my ipod touch and after it finished downloading a screan appear with just the apple symbol and a loading bar that is empty. it is completly unresponsive when i press the buttons and i didnt mess with it for a few hours hoping the bar would load but it didn't. i unplugged it from my computer then re plugged it in many times and when i plug it in nothing happens on my itunes account. i cant find anything in the manual and i dont want to have to buy anything so i cant call apple support! plz help me i dont know what i would do without my ipod for a day!

thank you so much! that worked! i was freaking out, i constantly use my ipod i dont know what id do without it!

Similar Messages

  • My iPod touch 4 is flashing on and off consistently with the apple logo.  This happen after I replaced screen?

    I need HELP!  My iPod touch 4 is flashing on and off consistently with a white background apple logo and it won't do anything else.  I have to completely unplug the power port from the inside.  This started after I replaced the screen. Any advice please help me  

    So I let it set all night unhooked from the power port and tried it today! It works! It acted like to battery was dead and recognized when I tried to power it on! All I can say it was a GOD thing! ;) I done a lot of praying!

  • I have an ipod touch that continues to have a black screen with the white apple on it. It won't shut off and is completely frozen. This happened when we tried to restore it last night. Help please!!

    I have an ipod touch that continues to have a black screen with the white apple on it. It won't shut off and is completely frozen. This happened when we tried to restore it last night. Help please!!

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar

  • Tryed to update my ipod touch last night, today it is frozen with the Apple symbol on the screen.

    tryed to update my ipod touch last night, today it is frozen with the Apple symbol on the screen.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • I started to restore my ipod and i unplugged it and it is now frozen at a screen with the apple logo and an empty loading bar

    i started to restore my ipod and i unplugged it and it is now frozen at a screen with the apple logo and an empty loading bar

    Try:
    iPhone and iPod touch: Frozen and unresponsive

  • HT3965 I got what appears to be a reconditioned (pre-owned) iPod Touch 4 for Christmas.  How can I change the Apple ID on tis device so I can use it with my iTunes Acct and Wi-Fi network?  Thanks.

    I received what appears to be a reconditioned iPod Touch 4th for Christmas.  How do I change the Apple ID on the device to my ID so I can use my iTunes account?  Thanks for any help/

    It would probably be best to attach the iPod to a computer and restore it. This way you'll know it's wiped clean. Then, when you start up the iPod it will ask you for your Apple ID.

  • My iPod 5th gen will not completely turn on it shows the apple symbol then shuts off I have restarted it and tried to plug it into my computer but cannot find it to restart it

    My iPod 5th gen will not completely turn on it shows the apple symbol then shuts off I have restarted it and tried to plug it into my computer but cannot find it to restart it
    Its been like this for awhile and I can not fix it

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                                                       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • Hello my Mac Air is frozen on the grey screen (with the apple symbol, sleeping mode, restart-and off button), once you turn it on.

    hello my Mac Air is frozen on the grey screen (with the apple symbol, sleeping mode, restart-and off button), once you turn it on. I Can`t press any button.My Mouse still works. Battery is charged. Alt-cmd-escape doesn`t work It even after a forced shutting off, the problem is the same.   what should i do? Thank you for your help.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
         a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Step 3
    Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
    If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
    If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 4
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 5
    Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
    Step 6
    Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 7
    Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
    Step 8
    This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. The battery is distinct from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
    Step 9
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

  • My ipod touch isnt working I tried to reset it and the apple logo comes up but then goes to a black screen. What else can I do?

    My ippd touch isnt working i tried to reset it and the apple logo comes up then goes to a black screen. What else can I do?

    Try connecting to your PC in Recovery Mode ane restore it.  See this article for help on getting your iPod into Recovery Mode.
    iPhone and iPod touch: Unable to update or restore
    B-rock

  • Help! I tried to power off my ipod touch 3gen-now I have a blank screen with a loading symbol.

    I tried to power off my ipod touch.  The screen showed the "slide to power off" button and "cancel".  I slid the power off.  Since then(30 minutes) I've had a blank screen with the loading symbol on it(moving loading symbol).  What do I do?

    Try a hard reset,
    Basic troubleshooting steps. 
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD  120G Vertex 3 SSD Boot HD  

  • My iPod touch 4g keeps going to lockscreen and back to the apple logo and I can't shut it off or anything

    My iPod touch 4g keeps going to lock screen and back to apple logo over and over and I can't turn it off or anything

    Try:                                               
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar              

  • My update failed and now my phone is frozen with the apple symbol

    I was updating my iPhone and it failed and now my phone is frozen with the Apple Icon.  It wont turn off or anything

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • I have my ipod nano 5th generation and when i plugged it to my computer it is recognized but i cant do anything. On the ipod all i can see is a black screen with the apple sign! How can i fix this?

    I have my ipod nano 5th generation and when i plugged to my computer it is recognized but i cant do anything. On the ipod all i can see is a blackscreen with the apple sign! How can i fix this?

    Howdy Lumagofe,
    I was thinking that you may need to reset the iPod Nano, outlined here How to reset iPod http://support.apple.com/kb/ht1320.
    Press and hold the Sleep/Wake button and Volume Down button simultaneously for at least eight seconds or until the Apple logo appears. You may need to repeat this step.
    If the above step did not work, try connecting iPod to a power adapter and plug the power adapter into an electrical outlet, or connect iPod to your computer. Make sure the computer is turned on and isn't set to go to sleep. Try resetting the iPod while it is connected to power.
    If that doesn't quite get the iPod going again, then it will need to be restored. Use this article to help with that Restoring iPod to factory settings http://support.apple.com/kb/ht1339.
    All the very best,
    Sterling

  • I have an iPod touch and an iPad4. iTunes lets me work with the iPod Touch but won't show me what's on the iPad. Any ideas?

    I have an iPod Touch and an iPad4. iTunes recognises both items and lets me work with the iPod Touch but won't work with the iPad. In fact iTunes does not respond to clicking on anything in the iPad window even though it knows that it's connected. Any ideas?

    Look her and it may give insite on what is missing. Otherwise:
    Apple will exchange your iPod for a refurbished one for $99. Likely not worth it for a your iPod. They do not fix yours.
    Apple - iPod Repair price              
    A third-party place like the following maybe less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Repair it yourself if you are up to it
    iPod Touch Repair – iFixit

  • My ipod touch was taken by a family member along with the box containing serial number.  Any way of tracking it ?

    My daughter's Ipod touch was taken by a family member...anyway of telling whether or not it was connected to a copmuter and re assigned under another name...Ipod was originally registered under my name.

    Sorry but no, there is not.
    Regards.

Maybe you are looking for

  • Php code is not working as intended in a simple spam block solution

    Hi. I'm trying to get some simple php code (as suggested on a tutorial page I found) to work on my form submission test page in order to reduce/stop spam. However, the results so far have not quite been what I expected. Any help will be appreciated.

  • ADConnector v9.1.1 and Windows 2008 R2 - Supported? (OIM 9.1.0.2)

    Below is my question around the OIM AD connector version 9.1.1 and its support with Windows Server 2008 R2. From the AD Connector Documentation I can see that Active Directory 2008 is a supported target system by the OIM connector v9.1.1. There is no

  • Can't connect to external monitor (possibly after Yosemite update)

    I have recently updated my macbook pro to Yosemite. My external monitor (samsung 1080p tv) would connect fine using a hdmi before, but now its unresponsive. I have been into adobe premiere pro CC and been onto preferences > playback > then ticked my

  • Solved: Dynamic Converter error - Can't get HTML rendition of files

    I installed the Dynamic Converter into Content Server on a Linux system, setup the paths to the fonts, and checked-in basic templates, layouts and scripts. When I check-in a new document (word document in this example), I get the following error: Con

  • Extracting metadata from PDF's

    I have a client that has hundreds of store signs as PDF's. We need to verify what the actual printed size of each sign will be when it's printed out. We have noticed that hovering our cursor over the lower left hand corner of the PDF's reveals it's s