My ipod touch screen has gone white

Please help my Ipod screen has gone white with a feint image

If not successful
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer                            
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar                                     

Similar Messages

  • My ipod touch screen has gone white with bright white spots, I have restored it but it is still white.  It shows in ITunes but I cant do anything with it.  Can anyone help please

    My Ipod touch screen has gone white with bright white spots on it.  I have restored it and it shows in ITunes but the screen is still white.  Is there anything I can do? The warranty has run out so I will have to pay for any repairs (if it can be repaired).  Any help would be much appreciated.  Thank you in advance.

    If you still have problems after restoring the iPod to factory defaults/new iPod then you very likely have a hardware problem.  I would make an appointment at the Genius Bar of an Apple store.

  • IPod Touch screen has gone white with grey lines

    I have had my iPod Touch for a year and a half, so unfortunately it is out of warranty. About two months ago it started behaving strangely. Every other time I turned it on there would be a white screen which after a few seconds would get slightly darker with vertical grey lines. The screen was still responsive, and you could hear clicking. Turning the iPod off and back on would resolve the problem and the screen would reappear with no problems at all.
    Unfortunately this got worse. Now I am unable to turn the iPod on without getting the white screen with grey lines. The iPod is still responsive. I can plug it into itunes and browse it normally.
    I've reset the iPod many times and completely reset it through iTunes with no luck.
    Any suggestions? Is this a hardware fault and is it possible to resolve? Or is there something else I can try? Any help would be very appreciated.

    My old Touch 2G has the same issue. The Apple Store Genius couldn't tell what's the problem. However, I observed that the white grey striped display appears almost every time (or at least far more often) when the iPod lays on a ground. It is fixed by tilting it 90°, so that the dock connector is pointing to the ground.
    And sometimes the density of stripes changes by pressing home (no, I don't mean switching from spotlight to first home screen page, because this happens in lock screen, when home button does nothing) or pulling out the dock cable. So I think it's something near the dock connector and home button. Hardware fail, maybe the not so fitting dock cable in the rounded dock connector is the issue.

  • My ipod touch screen has turned white. the screen has turned bright white. it is not going by reseting also. when  i  shift screens then it leaves a trail and i dont know what to do. please help.

    my ipod touch screen has turned bright white. the things are visible but partially and when shift the screen it leaves trails behind. i dont know what to do help please.

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • My iPod Touch 4G's screen has gone white and has lines on the screen. How do I fix it? Help!

    Hello everyone,
    I've had an iPod Touch 4th generation for a few years now, and, today, for the first time, the screen has gone white and their are vertical lines on it. What happened was I accidentally dropped my iPod Touch on tile and it landed on its back. I tried it out right afterwards to see if it was still working and it seemed like it was perfectly fine. Later on, I got an email from one of my friends, so I slid the email button on the lock screen to see the email. In the email, there was a link to a gif image, so I opened it in Safari. After I was done with it, I closed that tab. I also had a second tab open from earlier, so I wanted to close that tab as well. When I clicked on the button to see all tabs and close one, the screen completely froze. I held on to the on/off button on the top of the iPod, and, after about a minute, the screen switched to a completely white screen with lines on it. I've tried holding onto the on/off button again and it doesn't work. I also tried plugging it into my Windows 7 computer and opening iTunes, but my computer doesn't even recognized it is plugged in. It won't appear under the "computer" section in Windows Explorer, which will allow me to do USB-related tasks with it. iTunes doesn't recognize that it is plugged in either, so I can't do anything like restore the iPod to factory settings. The home button on my iPod hasn't been working for a while so i've always been using the accessibility feature that gives me a home button on the screen. Now that I can't access that, I can't hold down both the on/off button and the home button at the same time. What should I do? Should I send it in to Apple for repairs (which I won't do and would rather buy a new iPod Touch)? I am thinking of just leaving it to, hopefully, have the battery drain and the iPod would die. Then, I could charge it and see what happens. Other than that, i'm just clueless right now and I have no idea what I should do. Please help me!
    My iPod Touch is an iPod Touch 4th generation model with 8GB. It is running iOS 5.1.1.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                              

  • My Ipod touch 4G has a white screen.

    My Ipod touch 4G has a white screen.  I've followed all the troubleshooting tips - turning off (hard to tell when all you see is white), hard reset, and restore.  I updated to the latest software versions.  Itunes recognizes the ipod.  I restored it.  Nothing changed.  Still have the white screen.  It hasn't been mishandled - no cracked screen, no water, hasn't been dropped.  Any other suggestions or is it time to call Apple?

    If you have done al the hardware troubleshooting, call Apple to get it serviced.

  • My screen has gone white

    My screen has gone white, have tried some things to fix it but doesn't work. What can I do to fix it?

    Do a restore:

  • Can you replace a black iPod touch screen with a white iPod touch screen?

    I need help! Can you replace a black iPod touch screen with a white iPod touch screen?

    cjennings6211 wrote:
    cliftonfromrichmond, what are you talking about??
    I'm bustin' your chops.  Some call it humor, some don't have a sense for it....
    The real point is Kappy gave you a link to a list of video demonstrations of changing the digitizer to show you that what you intend to do can in fact be done.  However, not once but TWICE you questiofed what was freely given to you, and you obviously didn't take the time or make any effort to find out if white framed digitizers are available.
    The fact of the matter is, white framed digitizers are available, and rather inexpensively I might add.
    My post with the outrageous prices was intended to trigger some of your obviously dormant gray matter into some form of activity that might just resemble intelligent human thought and maybe generate a giggle or two.  Guess I was wrong....  But at least now I know why you have a picture of a box of rocks for your avatar....

  • Touch screen has gone black

    Printer works great when triggered from the computer,
    but the touch screen has gone to black, permanently.
    No matter how much i press,it stays black.
    I've unplugged and replugged.
    Downloaded a new driver which allows me to trigger the scan from the computer,
    but i can't get to the fax.
    Is this a driver issue, a hardware issue...?  Not sure what firmware is.
    This question was solved.
    View Solution.

    Hi @lenny15,
    Thank you for visiting the HP Support Forums!  I understand the touchscreen on your HP Photosmart 7515 is completely black, you are able to print from the computer but cannot access the front control panel.
    I would like you to perform a Hard Reset on the PS 7515:
    1. Unplug all cables and memory cards from the printer. Unplug the power cord, directly from the back of the printer while the printer is still turned on.
    2. Unplug the other end of the cord from the power source.
    3. If there is a power module on the power cord, disconnect one end and reconnect it.
    4. After 60 seconds, plug the cord directly into a wall outlet (not a surge protector or battery backup as they can cause the printer to lose basic functionality over time).
    5. Plug the power cord into the back of the printer.
    6. The printer should automatically power back up. If it doesn't, turn it on with the power button.
    7. Try making a photocopy (if your printer is an all-in-on printer) before connecting any other cables to the printer.
    8. Connect any other needed cables to the printer.
    If after the hard reset you are still not able to access the control panel, I suggest you call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    I hope this helps!
    HevnLgh
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Ipod mini screen has gone dark, and when backlight goes on v

    Ipod mini screen has gone dark, and when backlight goes on the centre part with writing etc is almost black with light around edge. will this go? do i need to send it back?

    Maybe your backlight is burning out? That's what I would think when the center is black but the edges have light. I'm not sure if a reset would fix the backlight but you can try (hold the menu and center buttons at the same time until you see the Apple logo and then release). If I were I'd send it back to Apple but do you know if you are still under warranty? You should be if you've had your iPod less than a year.

  • Ipod classic screen has gone blank possibly not charging

    My Ipod classic screen has gone completely blank. It is 5 months old. I am in San Salvador and cannot get any support from the i shop here. Can you help.

    Hello allan63,
    Thanks for using Apple Support Communities.
    To troubleshoot this issue where you're not seeing anything on your iPod classic's display, please follow the steps in the article linked to below.
    Apple - Support - iPod - iPod classic Troubleshooting Assistant
    Cheers,
    Alex H.

  • My Blackberry Curve 8520 screen has gone white but the sounds and everything still work

    My Blackberry Curve 8520 screen has gone white but the sounds and everything still work so i dont know what to do because nothing on youtube tells me what to do so i have ended up here so please can someone help me

    Hello grasyapagsinta
    Welcome to BlackBerry Support Community Forums
    If you think your Battery it OK then try Updating or reloading your device software to rule out any software issue.Have a look at  on how to perform a clean reload of device software :
     KB11320 : How to perform a clean reload of the BlackBerry Device software using BlackBerry desktop software for windows.
    Additional Information :KB30280 : BlackBerry smartphone displays a blank white or black screen.
    Prince
    Click " Like " if you want to Thank someone.
    If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.
    Click " Like " if you want to Thank someone.
    If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

  • My iphone  screen has gone white with a few grey lines down the right hand side.. Has anyone any ideas how I can solve this and get my screen back to normal..? Thanks

    my iphone screen has gone white with a few grey lines down the right hand side.. Has anyone any idea how I can solve this and get my screen back to normal..? Thanks

    Hi tag71,
    If you are having issues with the display on your iPhone, you may find the Display portion of the following article helpful:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Regards,
    - Brenden

  • My ipod touch screen froze and the screen has gone white and i cannot do anything. Is it broken? can it be fixed?

    My ipod froze during facebook and now the screen han gone white and i cannot do anything.

    - Try:
    iOS: Not responding or does not turn on
    - If not successful and you can't turn the iPod fully off, let the battery fully drain. After charging for at least an hour try the article again.
    - If still problem that indicates a hardware problem and an appointment at the genius Bar of an Apple store is in order.

  • My Ipod touch 4g has got White screen of death

    Hi guys. My Ipod touch 4g has got a blank screen after buying a game from app store. It froze on the game screen then went white. I've tried holding the home and lock buttons at the same time, and i tunes reset, but neither option has worked. Any potential sollutions would be appreciated.

    the same thing has happened to mine...Out of the no where the screen just turned white and i'v tried holding the home button+The sleep Button Nothing! and it doesnt show up on iTunes -.- i guess i have to waite till my batter runs out ughhh

Maybe you are looking for

  • App Store says 'wrong password' but it's not!

    [I can't find a specific iPhone App Store as opposed to this Mac App Store section ... I'm this is in the wrong place, please let me know and I'll move it!] Odd one this - I would really appreciate some help on this one! The apps on my iPhone 4 appea

  • Call function in update task empty variables error

    Hello, I'm experiencing a weird error while using the addition "In update task". My Scenario is the following: Use the bapi_goodsmvt_create -> if there are no errors, fill some values and call my function and then commit everything. The problem is, w

  • How to use the userid and password infor from Oracle DB in BO

    Out client has the userid and passwords(encrypted) infomration stored in oracle table. Is it possible to import this useid and password information into BO .And use the same userid and password from Oracle table for its login authentication and for d

  • Fusion order aplication demo

    Hi when i Install the Schema for the Fusion Order Demo Application , i get the following message: BUILD FAILED C:\fod\Infrastructure\Ant\build.xml:52: The following error occurred while executing this line: C:\fod\Infrastructure\DBSchema\build.xml:91

  • H:commandLink target attribute

    Hi All, A coomandLink when rendered in html takes the form <input name="com_sun_rave_web_ui_appbase_renderer_CommandLinkRendererer" type="hidden" value="" /> Click me If target=_blank is used additionaly, why wont it work on commandLink. Regards, Dar