My ipod wont restore. HELP!

when i restore it, it goes smoothly. but after i restore it, it stays in recovery mode. i tried the press the top and bottom thing thousands of times but it wont work! i need help! and good easy answers!

Let the battery drain completely.  Then recharge for at least an hour and Restore again.

Similar Messages

  • Help! ipod wont restore any firmware! what should i  do?!!

    i updated to 4.0.2 firmware any now i can restore to any firmware i have put my ipod into dfu mode and it wont restore help!

    You need to install the adobe flash player plugin.  Download only from the adobe flash player plugin download page.  Mount the downloaded dmg and launch the installer.  Check the agree to terms to enable the install button and then click the install button.
    Once installed, the next launch of your browser should allow you to play youtube videos and flash videos on other flash video sites.

  • HT201274 my ipod wont restore i need help

    my ipod wont restore i dont know what to do i need help.

    Without more information all I can say is try placing the iPod in Recovery mode and try restoring.
    Also see:
    iTunes: Specific update-and-restore error messages and advanced troubleshooting

  • HT201413 my ipod wont restore says an error occured (1)?

    my ipod wont restore says an error occured (1)?

    Hi missnaughty06,
    Thanks for contributing to the Apple Support Communities.
    It seems like your iPod can't be restored due to an "error 1" message, and you've found the article regarding resolving issues between iTunes and security software.
    Be sure to follow the steps in that article to make sure that iTunes can communicate with your iPod. If you continue to see the error message, this article on restore errors suggests contacting Apple Support at this point:
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
    Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
    Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
    Confirm that your security software and settings are allowing communication between your device and update servers.
    If you still see the error message when you update or restore, contact Apple support.
    From:
    Resolve iOS update and restore errors - Apple Support
    All the best,
    Jeremy

  • My ipod wont restore screen jus black

    my ipod wont restore always different error everytime screen is jus blank

    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    Finally, if the Restore doesn't work, let the battery drain completely.  Then recharge for at least an hour and Restore again.

  • HT201263 my ipod wont restore what can i do?

    my ipod wont restore what can i do?

    are you getting a restore error code, what is happening when you try to restore.

  • My 4th Gen iPod wont restore because of error 3194. PLEASE HELP?

    It went into recovery mode, and so i plugged it into iTunes. However when I plug it up it says it needs to be restored, and it wont restore because of error 3194. Nothing I have read yet is helping.

    Okay! I may have a solution for some of you! I have a 4th gen click wheel, and it was doing the whole restart thing over and over, but never getting past the apple logo.
    You need to get to the diagnostic mode. To do this I had to hold down the select and rewind buttons at the same time. (for some models it's the sel/ff buttons or the ff/rw at the same time. The Apple logo will briefly appear backwards, and then you should hear a chime. My screen came up as:
    IRAMPASS
    PLAY TO CONTINUE
    (and some other junk)
    press play.
    Another menu will come up, scroll through the menu (my Ipod I had to click ff to scroll through. There were 3 pages to scroll through. I got to disk mode on that menu and with the ipod connected to my computer, I started disk mode. Once disk mode started my computer recognized the ipod (finally) and I was able to restore from the computer.
    I did lose all the music stored on it, but I'm happy to have made this progress, considering when I got this ipod from a friend two days ago, who was about to throw it in the garbage, it would not even turn on!
    Hope this post helps someone!

  • Itouch wont restore   HELP PLEASE

    i have a 2nd or 3rd generation itouch. when i unplug it from charging it doesnt work. and when it is pluged in the apple logo appears. i tried restoring it but i wont restore. all it says is "the ipod "******"could not be restored. an unknown error occered (1602). how can i fix this? PLEASE HELP ME

    As mentioned in your other post:
    Here are some suggestions, copied from Update and restore error messages on iPhone and iPod touch
    Error 1604
    This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
    If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
    Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
    Restore and wait for the error.
    When prompted, click OK.
    Close and reopen iTunes while the device remains connected.
    The device should now be recognized in Recovery Mode again.
    Try to restore again.
    If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
    Error 1600, 1601, 1602
    Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.

  • Ipod wont restore, why?

    my ipod touch 4g wont restore or go into recovery mode, keeps coming up with error code 11. however error code 11 isnt on the apple website. Help anyone?
    Thanks

    try restoring the device in DFU mode. while connected to the computer and itunes open, press and hold the power button and home button at the same time and count to 20 then release the top power button while continuing to hold the home button. the screen on the ipod should still be black and you should see a message pop up on the itunes window. follow steps on screen and restore from there

  • Ipod wont restore or go into disc mode

    My ipod wont turn on properly. when i try it displays the apple icon for a few seconds and then the folder/exclamation mark icon before turning itself off. I tried restoring the software but i get an error message saying 'can't mount ipod'. It wont go into disc mode either, i just get the apple icon. I think it needs professional help and i know it hasnt been a year since i bought it and it should still be under warranty but i cant find my receipt. any help would be greatly appreciated.
    thanks

    I just updated itunes with my ipod connected.  When the update finished my computer didn't recognize the ipod and then itunes thought there were 2 ipods connected to my computer.  After I disconnected the iPod I tried to turn it on where I get the big red X and what sounds like hard drive crunching.  I've tried started in disc mode, but it won't.
    And smacking the iPod on the table, is that really the way to get it to work???

  • My ipod wont restore

    i have just downloaded the new software for my ipod touch and it has went into recovery mode, i have clicked on the restore button and then it came up with error 22, i then deleted my anti virus software as apple has said but it still wont restore, now it is coming up with error 21 and still wont restore and is still stuck in recovery mode. If anyone has had this problem and has sorted it can you please help me as I am about to go to the local apple store and give them a piece of my mind and demand my £225 back or throw the ipod out the window as it is now a useless piece of dung

    Did you check your security software settings to provide contact to Apple during the restore process?
    http://support.apple.com/kb/TS3125
    If this does not work, try to delete the ipod software file located in C:\Documents and Settings\username\Application Data\Apple Computer\iTunes\iPhone Software Updates to make iTunes download a new copy when you connect in recovery mode. Maybe the file stored on your PC is damaged.
    Recovery mode: http://support.apple.com/kb/HT1808

  • Ipod wont restore, (-69)

    i dont know what to do my ipod wont update, or restore.it always says unkown error (-69). I cant find a corrupt file eather. Your responses are appriciated, thanks.

    What does the error message say:
    See:
    iTunes: Specific update-and-restore error messages and advanced troubleshooting

  • Ipod wont restore, continuous "Restoring Ipod" bar...

    My ipod one day just came up with a restore with itunes screen, so I pluged in my ipod, open itunes, it finds the ipod fine, it say it needs to be restored fine, but it never completes stage 9 in the manual "A progress bar will appear on the computer screen indicating that the first stage of the restore process has started. When this stage is completed" the bar just keeps going, for over 48hrs it goes, and i cant get past this now... please help me...

    i have the exact same problem.. ipod says connect to itunes in 4 different languages, after connecting itunes says ipod detected in recovery mode and needs to be restored.. after restoring it detects its still in recovery mode loops constantly.. i've tried the 5 r's, all the help on the apple site and also tried changing the drive letter as also suggested.. and to no avail..
    5th gen video ipod.. please help!
    sim

  • Ipod wont restore it just keeps saying to restore again

    i changed the password on my ipod touch 5 and i forgot it almost immediatley! It said connect to itunes after so many password attempts so i tried that! i had never actually synced before so it required a password to connect and obviously that didnt happen because the ipod was disabled...
    i tried the advice on this site and set my ipod to restore mode, and itunes began to restore it, but every time it finished, the itunes store told me that it needed to be restored again! So it just kept going in this loop although nothing was actually happening! What should i do? Please i need an answer asap

    Did you already try this?
    Restore loop (being prompted to restore again after a restore successfully completes)
    Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
    copied from iTunes: Specific update-and-restore error messages and advanced troubleshooting

  • IPod wont restore

    I'm having a lot of trouble with my new iPod Classic 160 GB. It suddenly stopped working properly and wouldn't sync with iTunes. I synchronized it, but all the music from my iPod disappeared. I reconnected it hoping syncing it again would fix the issue, but my iTunes said I had to restore my iPod before using it again. So I restored my iPod, and it restores it normally, but straight after it turns back on after restoring I get the same message from my iTunes. I keep getting error message 1429 after restoring. I managed to get my iPod restored once, but trying to sync it just borught the problem back.
    I've tried everything I've found online to fix it - trying another USB port, reinstalling iTunes, starting iTunes in safe mode, even hitting the top right corner,  (it's supposedly worked for some people) - among other things.
    Does anyone know what the issue might be?

    Hey there Penthe,
    It sounds like you are getting error message 1429 after restoring your iPod. I recommend the other troubleshooting steps from the article named:
    iPod: Can't restore or update in iTunes with error 1415, 1417, 1418, 1428, 1429, 1430, 1436, or 1439
    http://support.apple.com/kb/ts1372
    To troubleshoot the error, follow these steps:
    Disconnect and reconnect your iPod to iTunes and restore or update the iPod.
    Restart your computer and restore or update the iPod.
    Connect your iPod to a different USB port (a USB 2.0 port if possible) and restore or update the iPod. For Windows computers, follow these steps to identify USB 2.0 ports.
    Disconnect any third-party USB devices from your computer. You don't need to remove your keyboard or mouse. Then, restore or update the iPod.
    Update iTunes and restore or update the iPod.
    Use a different user account on your computer to restore or update the iPod. For example, create a new test user account on the computer with admin rights and iTunes and restore or update the iPod.
    Turn off Disk Use on your iPod and restore or update the iPod.
    Turn on Disk Use on your iPod and restore or update the iPod.
    Reregister ".dll" files by using these steps under "Solution 1."
    Update or reinstall your Windows USB drivers using these steps under "iPod only: Updating, or in some cases reinstalling, the drivers for your computer's USB interface may resolve this issue."
    If you use third-party security software, you might need to update, disable, or uninstall your security software temporarily.
    Thank you for using Apple Support Communities.
    Regards,
    Sterling

  • Ipod wont restore to 5.0, ipod wont restore to 5.0

    ive tried the suggested stuff (make sure my usb port is fine, security up to date) but it just wont restore it shows the 1601 error plese help

    sry about this my question is irelevent now plese dont reply i managed to do it but it icloud deleated all my pics and app data

Maybe you are looking for

  • Error converting to cap file

    Hello everyone, I tried to follow sample of java card kit, but I've got this error when I 'd like to convert class file to cap file with converter. Assertion (precondition) [member != null] failed at: What's wrong ???? It's out only jca and exp file

  • RH10 and Windows 8 Bug with DHTML

    I reported the following bug today: Concise problem statement: All DHTML effects in WebHelp-with the sole exception of drop-down and expanding hotspots-fail to execute on CLEAN Windows 8 systems (upgraded Windows 8 systems from Windows 7 do not seem

  • Why is my 3D menu greyed out? (Photoshop CC)

    Sorry if I'm asking this in the wrong place, first time I attempt using these forums! I have recently installed Photoshop CC, and I'm experiencing that the 3D menu is all greyed out - I remember using it without problems in CS5. System Info Adobe Pho

  • Apple map still does not show traffic

    Apple map still does not show traffic

  • Session state and LOVs

    Hello, I'm pulling my hair out attempting to have an LOV act correctly (like an unruly kid). The problem is where you are selecting an existing record and then this is taking you to an update page. On the update page, there is LOV1 where the value sh