My Keyboard and touch-pad will work during post, but will not work after the os loads?

I have a G60 and My Keyboard and touch-pad will work during post, but will not work after the os loads? Im running Windows 7, Anyone have any Ideas? I have already tried a hard reset, and safe mode???

Try pressing the fn key and f2 to reach bios
or
try a usb mouse from your desktop
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Similar Messages

My Hp Pavllion dv7 keyboard and touch pad will not work

Hi. My Hp Pavllion dv7 keyboard and touch pad will not work. Been going on for a few months now. Read in the support forum that replacing the battery might help however it hasnt. Ran updates for Windows Vista and Microsoft Security Ess. Boots up just fine however unable to place in my password to get to my user profile and always have to work from guest......unless I have a USB keyboard handly at the time. I use a USB wireless mouse as well.
Please help and thank you

The keyboard and mouse (touchpad) are separate devices which could go bad at the same time but that would be a huge coincidence. I would try reseating the ribbon cables to the motherboard for both. Here is the Service Manual:
Manual

Keyboard and Touch-Pad Not Working After Having to Install New Hard Drive

I had to install a new hard drive in my HP Pavillion DV9700t that has Vista Home Premium 64-bit. After going through the recovery process with backup disk the built in keyboard and touch-pad do not work. During the installation, an error message came up saying something along the lines of "the drivers are not supported by this verison of windows because they are unsigned." The drivers that had that error were "hpqkbfiltr keyboard filter driver," "HP remote control HID Device," and "hpqkdfilter driver." I tried to update the drivers for the keyboard from the hp website, but the keyboard and touch-pad still do not work.
My question is, where do I find the digitally signed drivers for the keyboard and touch-pad that Vista won't flag and disable?
Help please!

Sparkles,
Thanks for the suggestions.
When dealing with MS Fix It, I was choosing run. Upon further investigation on that site, there really isn't a scan that applies to my issue anyways I tried the .NET Framework repair tool, and that seemed to work. It told me to try re-running what I was having issues with, so I tried running the Windows PowerShell again, but again was faced with the following message "windows update standalone installer encountered an error: 0xc8000247." I went back to the .NET screen and hit "Next" because it didn't work, and that responded by saying they were going to submit logs to Microsoft. I won't hold my breath on that one.
I'm to the point where I honestly don't care anymore. I have no idea what to do, because doing a clean install with the discs HP sent me isn't going to help because they are just recovery discs, and not an actual Windows disk. This is the second hard drive I have had to put into my laptop and use those recovery disks on in the last 3-years. The built-in keyboard hasn't worked during that time frame on either hard drive. I don't think the recovery disks I was sent install properly. Not sure where to go from here. I spent way too much money on this laptop years ago having it custom built to handle all of my drafting programs, so I don't want to just kick it to the curb. I was looking into the possibility of just replacing it, but I cannot stand the Windows 8 interface.
I guess I should have fixed the issue with the keyboard on this hard drive before loading all of my programs. Between the recovery disk install, formatting of the hard drive, and installing all of my programs it took well over 12 hours. Not really looking forward ot that again Then there's shockwave and flash and all of the other goodies that my recovery disks won't restore anyways.
Sorry if this seems like a negative post, but I'm just tired of trying to no avail. Maybe I should just take it somewhere to get it looked at, but I can't see them being successful if the recovery disks won't help anyways.
Thanks for you help,
MadBuch

My keyboard and touch pad just randomly stopped working, how do I fix it?

My keyboard and touch pad randomly stopped working and now I can't do anything, does anyone know how to fix this?

Try SMC and PRAM resets:
http://support.apple.com/kb/ht3964
http://support.apple.com/kb/ht1379
Ciao.

Cannot load the recovery media since my keyboard and touch pad do not work

My labtop Toshiba C55D-A5392 may have a virus issue which cause the keyboard and touch pad do not function. initially only a few keys don't work...after a couple days most keys don't work and now no keys are working and the touch pad failed too. I can't even load up windows now. I bought a recovery media from toshiba and try to reset the laptop to factory settings. I received the USB drive media from Toshiba, but I cannot load it since I cannot get the laptop into the bios (since my keyboard does not work). Can anyone help me to resolve this issue?

Try pressing the fn key and f2 to reach bios
or
try a usb mouse from your desktop
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Keyboard and Touch Pad are Dead!

Today the keyboard and touch pad died on my MacBook Pro. Both were working fine earlier this morning, but suddenly stopped working this evening. Not only that, but now OS-X takes a very long time to boot and shut down as well as Windows Vista on my bootcamp partition. Also, the cooling fan spins at full speed during boot-up and stays at full speed when the login screen appears. It never did this before.
I connected a USB keyboard and mouse to my computer, and they worked fine. I have tried the SMC reset, but the problem still persists. I have tried safe boot, but it doesn't work. Is this a case of corrupted files or something more sinister?
UPDATE
I noticed that I no longer have a sound device. When I opened Sound, there was no device listed at all. Also, the fan is running at full speed when the CPU load is minimal (98%-100% free). Think I'm gonna need some Crown and Coke after tonight.

I took your advice and went to the Apple Store in Ginza, Tokyo. I was so surprised at how easy they made the entire process! I will have my MacBook Pro repaired at no cost, because it is still under warranty. A lot of companies could learn from Apple's customer support model! Finally, you should see the fancy Star Trek-like elevator!!! Unbelievable visit today!!! Thanks Apple!

Dynabook C7 - Need part number for keyboard and touch pad

Hi there!
I have a few questions about my toshiba dynabook C7 laptop.
I want to change my old keyboard and touch pad as they do not work properly. The problem is that i can't find those parts because this model was delivered only for Japan market. So maybe somebody knows number of the models of those parts that might be suitable for my laptop? Or name of the laptop that is similar to my dynabook c7. The full model name is TOSHIBA DYNABOOK C7/212CMEN portege 4101 series
Thx in advance.
Cheers!

Hmmm... it can be pretty complicated. As you probably know it is not easy to get any info about those specific for Japan produced notebooks. I am pretty familiar with Toshiba notebook models and your notebook can be the same as Portege A100.
Google a little bit around and try to find info about Portege A100. I believe this notebook was offered in UK only.
Check also in Google - P000398500 G83C0001Q710 for Portege A100 series, Uk United kingdom keyboard.

Conflicting device error for keyboard and touch pad on thinkpad laptop

Hello,
IBM Thinkpad T43
1875
Windows XP (SP3)
Keyboard and touch pad completely do not work in Windows.
They do work in BIOS.
Tried connecting external USB keyboard. They also does not work
Getting Conflicting Device error in Device Manager for keyboard and touch pad
exclamation point is on the keyboard device.
getting Error Code 10 on keyboard.
I cant go to a prior restore point. That does not work.
tried uninstalling them, that didn't work either.
can't change auto configuration...it is grayed out.
Please help.
What can I do?

This is really strange I must say...
But you say you are using the same drivers for both 32-bit and 64-bit, this shouldn't affect the PE-part, but make sure you are using the correct drivers 64-bit for x64 OS and 32-bit for x86 :)
If you make a bootable memmory stick from the 32-bit deployment share, does it work then or is it the same problem?
Could it be as easy that the deployment share isn't updated?
//Andreas
Andreas Molin | Site: www.guidestomicrosoft.com | Twitter: andreas_molin
I also said that nothing's missing so, I thought it implies that only correct drivers are there.
I filter out all unwanted versions from both deployment shares to save on disk space.
Deployment Share have been refreshed several times with refreshing PE images too.
Mem-stick for 32-bit version works fine - keyboard and touch-pad work in it.

Non-responsive keyboard and touch pad

I have a dv7-3065dx Entertainment Notebook. After the computer starts up and reaches the windows login screen, the keyboard and touch pad are non-responsive. The curser is blinking in the space to type the password, but I cannot type anything. Does anyone know what is wrong and how to fix it?

Hi,
Can you access Windows Recovery Console by tapping away at f8 as you start the notebook?
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

I forget my password to my ipod and i have try to rerstart it but its not working what should i do?

i forget my password to my ipod and i have try to restart it but its not working. i have done i could think of please help!!

If You Are Locked Out Or Have Forgotten Your Passcode or Just Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. iOS- Understanding passcodes
4. What to Do If You've Forgotten Your iPhone's Passcode
5. How to Recover Forgotten iPhone Restrictions Passcode | The iPhone and iPad Blog
     If you have forgotten your Restrictions code, then follow the instructions
     below but DO NOT restore any previous backup. If you do then you will
     simply be restoring the old Restrictions code you have forgotten. This
     same warning applies if you need to restore a clean system.
A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
     1. Verify that you are using the latest version of iTunes before attempting to update.
     2. Connect your device to your computer.
     3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
     4. Select the Summary tab.
     5. Select the Restore option.
     6. When prompted to back up your settings before restoring, select the
          Back Up option. If you have just backed up the device, it is not necessary
          to create another.
     7. Select the Restore option when iTunes prompts you (as long as you've backed up,
         you should not have to worry about restoring your iOS device).
     8. When the restore process has completed, the device restarts and displays the Apple
         logo while starting up:
           After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
          to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
          iOS, keep your device connected until the "Connect to iTunes" screen goes away or
          you see "iPhone is activated."
     9. The final step is to restore your device from a previous backup. If you do not have a
          backup to restore, then restore as New.
If you are restoring to fix a forgotten Restrictions Code or as a New device, then skip Step 9 and restore as New.

I cant open my ipad after i turned on the voice in accessibility i have a passcode and i tried to enter my password but it not working. help me please

i cant open my ipad after i turned on the voice in accessibility i have a passcode and i tried to enter my password but it not working. help me please..
i updated my ipad in ios 6

Turn off VoiceOver
1. Press the Home button
2. Tap Settings.
3. Then double-tap Settings.
4. Tap General.
5. Then double-tap General.
6. Use three fingers on the screen to scroll to Accessibility
7. Tap Accessibility.
8. Then double-tap Accessibility
9. Tap VoiceOver
10. Then double-tap VoiceOver.
11. Tap "On" next to VoiceOver
12. Then double-tap "On" to turn it off.

It's been a while that Im unable to copy music from itunes to my iphone. I updated my device to the latest version of IOS 5.1.1 and made sure no jailbreak is installed but still not working. please assist.

it's been a while that Im unable to copy music from itunes to my iphone. I updated my device to the latest version of IOS 5.1.1 and made sure no jailbreak is installed but still not working. please assist.

Assuming you are not manually managing your music, verify the following:
You are using the latest version of iTunes
On the summary tab of your iTunes sync settings you have checked "Sync only checked songs and videos"
In your music library you have checked all the songs you want to sync to your phone
There are no exclamation points next to any of the songs you want to sync to your phone
You have authorized your computer for all Apple IDs for purchased music you want to sync to your phone (in Store>Authorize this computer)
You have checked "Sync Music" on the Music tab of your iTunes sync settings
When everything looks correct, sync your phone.

Hp Pavillon dv7 keyboard and touch pad won't work!!!!

My touch pad and keyboard on my laptop will not work unless i how the power button for a minute while no power is hooked up.

The keyboard and mouse (touchpad) are separate devices which could go bad at the same time but that would be a huge coincidence. I would try reseating the ribbon cables to the motherboard for both. Here is the Service Manual:
Manual

Helix will not connect with keyboard and touch pad

This is kind of wierd. It's been doing this since I've owned it. I have a Thinkpad USB 3.0 port replicator. When I get to work, I used to turn the screen around backwards on the keyboard and plug it into the PR. That way all you could see was the screen. Now I have a tablet stand and I remove it from the keyboard and set it in the stand. The problem I'm having is that when I have it reversed on the keyboard OR off of the keyboard all together for a period of time (say, 30 minutes) and I re-attach it to the keyboard, I can't use the keyboard or trackpad unless I press the power button for 20 seconds and hard reset the tablet. It see's the battery and plays the audio that tells me it see's it, but the pad and keyboard are unresponsive. It's frustrating. A standard reboot/restart will not fix the problem. I have made sure my tablet and keyboard have the latest BIOS and firmware updates.
SMBIOS - 2.7
UEFI Bios - 1.27
Embedded Controller Version - 1.21
It's frustrating to have to force a restart every single time I want to dock it after it's been off the keyboard for more than 20 minutes.
Any idea's?
Gavin

Does Axis say it is compatible with a 4G iPod with iOS 6.1?
Sometimes this works
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.

Pavilion dv7 entertainment PC keyboard and touch pad don't work.

Hey I just updated my computer from hp health check and now my built in key board and mouse are not working. I tried restarting it and even taking out the battery holding the power button for 30 sec and that didn't even work so now I'm stuck on what to do and my web browser says I can't talk to any one live at the moment. Please help I have a paper I need to type by friday and this usb keyboard doesn't work very well.

Try pressing the fn key and f2 to reach bios
or
try a usb mouse from your desktop
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

My Keyboard and touch-pad will work during post, but will not work after the os loads?

Similar Messages

Maybe you are looking for