My late 2006 20" iMac needs some TLC?

I recently added 2GB of memory after talking to Apple support as a way of speeding up my late 2006 20" iMac.  Unfortunately, that was NOT the solution.  So here's my problem:  I can do very little, from scrolling to even moving the mouse cursor without the rainbow wheel turning.......and turning, and turning.  In short, I am being held captive by a all-but-functionless computer.
I've run MacKeeper, TechTool device and MacScan all with the hopes of speeding my iMac up, but to no avail.  And there is still a good deal of space left on my Hard Drive.  Can anyone offer some possible solutions?  I'd like to conquer this problem before moving on to a new iMac.

First you need to uninstall MacKeeper: How to Remove MacKeeper. Uninstall MacScan and TechTool. See the following:
Things You Can Do To Keep Your Computer From Slowing Down
If your computer seems to be running slower here are some things you can do:
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Repair the Hard Drive - Lion
Boot from your Lion Recovery HD. When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Restart your computer normally and see if this has helped any. Next do some maintenance:
Suggestions for OS X Maintenance
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior;  DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep.  Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger.  These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems. For more about malware see Macintosh Virus Guide.
I would also recommend downloading a utility such as TinkerTool System, OnyX 2.4.3, or Cocktail 5.1.1 that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc.
For emergency repairs install the freeware utility Applejack.  If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line.  Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
  1. Carbon Copy Cloner
  2. Data Backup
  3. Deja Vu
  4. SuperDuper!
  5. SyncTwoFolders
  6. Synk Pro
  7. Synk Standard
  8. Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Open Activity Monitor in the Utilities folder.  Select All Processes from the Processes dropdown menu.  Click twice on the CPU% column header to display in descending order.  If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar.  Click on the Force Quit button to kill the process.  See if that helps.  Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file.

Similar Messages

  • Late 2006, 24" iMac, 2.16 GHz Intel Core 2 Duo, Screen Tearing, nVidia 7300

    Late 2006, 24" iMac, 2.16 GHz Intel Core 2 Duo, Screen Tearing, nVidia GeForce 7300 GT
    I've been suffering with screen tearing, strange screen artifacts, etc. followed by totally unresponsive freezing machine. This problem has been happening to varying degrees for about 9 months.
    Initially, I was able to mitigate the problem with smcFanControl. Adjusting the fan speeds up helped keep the machine cool and prevent most of the problems. Recently, we had a spell of hot weather and the fans just couldn't keep up. If you're using smcFanControl, the only fan speed that will really make a difference is the CPU. The HDD and ODD fans are no where near where you need to be.
    Also, I noticed the machine was LOADED with dust when I took it apart, including the heat sink fins for the graphics card. If you have time you may want to try a thorough cleaning with compressed air before replacing the card. You just need to get through step 11 below to access what needs to be cleaned.
    Based on reading here and elsewhere, I decided to replace the graphics card. To give back to the community, I wanted to layout the procedure here.
    Where to buy the card.
    I had a tough time finding the right card. I did exhaustive web searches using every combination of Nvidia 7300 GT, etc. You really need to search by the Apple part number. The Apple part number for the 7300 is 661-4179, for the 7600 is 661-4180. I found it at We Love Macs and at dv warehouse. I paid $248 for the 7600 card. BE CAREFUL buying a "refurbished" card. At We Love Macs, "refurbished" means "pulled from a working machine." Could be a machine with as much mileage as yours and prone to the same failures as yours.
    The card is an MXM style card (generally used in laptops), with a giant heat sink and heat pipe assembly. The card can be separated from the heat assembly. If I had time, I would have tried a generic, cheaper, MXM style card.
    Dispelling some myths.
    People here and elsewhere have said that no Intel iMac graphics card can be replaced, that they're wedded to the logic board. The one on this model can be replaced, I've done it. Also, some have said you can't put a 256MB, 7600 GT in a machine that originally had a 128MB, 7300 GT. Also, not true. That's what I did to my machine and it is working fine.
    So here's the step-by-step on my take apart and replacement. This is just one user helping out others, PROCEED AT YOUR OWN RISK. This takes about 1 1/2 hours to take apart and 2 to put back together.
    1) Install the iStat widget and monitor the temperatures for a few days and record the temperatures (to be able to verify that you've completed the repair correctly later)
    2) Make a complete backup of any internal drives and make sure the backup will be bootable (use Carbon Copy Cloner)
    3) Use static safeguards, like an anti-static wrist strap.
    4) Get a pen a stack of paper envelopes to separate and label the pieces you remove.
    5) You'll need a #2 Phillips and #6, 8, 10 Torx. Most of the screws at T-8. There are 8 T-8s holding in the LCD. They are about 1 1/4" down. You'll need a long, skinny T-8 to get to them.
    6) Unplug the machine and place it on it's back on a large white sheet of paper.
    7) Remove RAM door, #2 Phillips x 2.
    8) Remove RAM.
    9) Remove 4 T-8s along bottom.
    10) Remove large rectangular plastic bezel surrounding the whole machine, tilt up being careful not to stress iSight cables. You'll need to stretch it around the RAM ejection tabs.
    11) Detach two iSight cables.
    12) Peel up black stickers at lower corners of speakers.
    13) Remove LCD screws, T-8 x 8. You'll probably drop a few, they're pretty easy to retrieve.
    14) Remove two retaining screws on right hand LCD cable. T-6 x2 Unplug cable.
    15) Remove LCD inverter cable, left.
    Start unplugging everything connected to the logic board.
    16) Unplug cable coming from right speaker. Note cable routing, it is the only one that's a little tricky. Also, note that the left one plugs in on the right and the right one plugs in on the left.
    17) Remove right speaker. T-10 Note: left and right speaker screws are different lengths.
    18) Unplug ODD blower cable.
    19) Unplug ODD temp cable and lift up tape.
    20) Unplug HDD blower cable.
    21) Unplug the HDD temp cable.
    22) Unplug the camera & mic cable.
    23) Unscrew the clamp securing the airport card (has two antenna cables going to it, labeled PCIE), T-6 x 2
    24) Unplug SATA cable.
    25) Unplug Power cable, thick black plastic harness, socket.
    26) Unplug ambient temp cable.
    27) Unscrew the bluetooth card, T-6 x2.
    28) Unplug CPU blower cable.
    29) Unplug power button cable, 2 conductor, tiny cable, bottom left.
    30) Unscrew left speaker, T-10, unplug from logic board, but just leave dangling, no need to remove cable completely.
    31) Remove logic board screws. Be careful to segregate them, they have different lengths and different thread pitches and thread types. Some are machine threads going into metal, some are coarse threads going into plastic.
    31a) Heat sink frame to case T-8 x 2
    31b) Logic board to case T-8 x 3
    31c) Screws at heat sink from arrows T-8 x 3
    31d) Logic board at bottom near RAM slot T-8 x 2
    32) Unplug ODD ribbon cable, be extremely careful. Release plastic tabs on each side to remove. Be sure it is fully and evenly seated when you put it back later.
    33) Remove logic board with attached graphics card.
    34) Unplug graphics card heat sink sensor cable at logic board end.
    35) Remove graphics card screws 2 x T-6
    36) Remove single screw from small L-bracket on heat sink 1 x T-6
    Replace graphics card.
    Reverse steps, put everything back together. Be careful not to pinch any cables when you put the logic board back in. When you put the LCD back in, if you can't get the screws to stick to the driver, use some glue stick from your kid's art supplies.
    Test everything. You've disconnected every cable in the system.
    I torture tested the machine with a space heater on it, 5 different videos of different formats playing at the same time. No problems.
    I took a lot of pictures inside the machine. As soon as I figure out a good place to post them, I'll try to add a link here.
    Good luck

    Greetings!
    I know this is in response to your post from over 2 years ago, but I was searching on Apple's site for the max RAM I can upgrade our refurbed iMac too and it brought up this post.
    Oddly enough, I've been experiencing the same screen issues and locking up on our iMac as well. I was concerned it was a bad memory module, but now I'm thinking it's the same issue you found.
    Because I bought this some 2+ years ago refurbed from Apple, I'm not surprised that could be the actual problem.
    I've pulled this thing apart once to replace the hard-drive which crashed about a year ago, so I'm not totally new at opening it up, but this process you mention sounds pretty intense...just wanted to get your second take on it based on what I've done thus far.
    Thanks again for posting this...it was an eye-opener as to what might actually be causing our issues with our trusted Mac!
    Joshua

  • I need to replace my late 2006 20" imac hard drive

    here's what i have
    VIN,IMAC (20-INCH LATE 2006)
    running leopard 10.5.8
    Hardware Overview:
      Model Name: iMac
      Model Identifier:    iMac5,1
      Processor Name: Intel Core 2 Duo
      Processor Speed: 2.16 GHz
      Number Of Processors: 1
      Total Number Of Cores: 2
      L2 Cache: 4 MB
      Memory: 3 GB
      Bus Speed:    667 MHz
      Boot ROM Version: IM51.0090.B09
      SMC Version (system): 1.9f4
      Serial Number (system): W8******VUV
    WDC WD2500JS-40TGB0:
      Capacity: 232.89 GB
      Model:    WDC WD2500JS-40TGB0
      Partition Map Type: GPT (GUID Partition Table)
      S.M.A.R.T. status: Failing
      Volumes: Macintosh HD:
      Capacity: 232.57 GB
      Available: 106.04 GB
      Writable:  Yes
      File System: Journaled HFS+
      BSD Name:    disk0s2
    disk utility shows this:
    my mac is still running like a champ but as the pictures above show it's time
    i've found a lot of people with the same question i have on this site with answers but most links that people suggest are broken or 2 of the hard drives they've recommended are discontiued
    i've got a frys electronics and best buy near by or internet if that's the best way to go about it
    what exactly do i need to look for when i'm at a store or online?
    what size hard drive, any? 250GB, 500GB, 750GB, 1TB
    3.5" SATA
    7200RPM
    does cache matter?
    anything else?
    people's responses to: Need to replace my late 2006 imac hard drive - what should i be looking for to replace it?
    1. You can use any 3.5" Sata drive, WD or Seagate would be good choices.
    2. Do not use "green" drives like the WD Blue series. WD Black are fine as are Seagates.
    3. The 2T green will work fine in the Intel iMac's. I always suggest using the quieter and cooler running Blue's or Green's in the iMac's.
    4. Personally I have upgraded the Hard Drive in several Early Core Duo's using both 320GB and 500GB WD Cavair Blue's.
    5. WD Caviar Blue or WD Caviar Green, they run cooler and quieter than the WD Black or Seagate's.
    6. I'm very happy with the WD Caviar Blue that replaced my factory installed 160GB Seagate HD a few months ago.
    i've found some good DIY tutorials for install
    http://www.youtube.com/watch?v=ShY8zuT-wPg&feature=player_embedded
    http://www.ifixit.com/Guide/iMac+Intel+20-Inch+EMC+2105+and+2118+Hard+Drive+Repl acement/1092/1 
    any help will be appreciated,
    sean k
    <Edited by Host>

    thanks for the quick reply kappy,
    i plan to purchase a new imac when they are actually shipped, in stores, and i know all my handicap assisted devises will work on it
    you say "Do not buy a drive designed for SATA 3 6 Gb/s interfaces as some may not work on the controller in your iMac"
    at frys it breaks the groups like this:
    Interface (32)  
    SATA/300 (17)
    SATA/600 (9)
    PATA/100 (6)
    could you take a look at this link to frys and recommend a hard drive
    http://www.frys.com/search?cat=-69564&pType=pDisplay&fq=100413%203.5-100415%2072 00
    or bestbuy internal hard drives
    like you said it's got a limited life and just need something to get by till the new imacs arrive

  • HT201295 Late 2009 Intel iMac Needs Frequent SMC reset - constant high speed running fan

    Late 2009 Intel iMac is having reoccurring episodes of high speed fan running, especially after waking it up. The SMC reset by unplug and reboot works, but I worry that this is a serious sign and that the machine is slowly dying. Any thoughts? Works fine otherwise.

    wolfgang272 wrote:
     Do you have any ideas?
    Yes, you just need to reset the SMC and you should be fine
    https://support.apple.com/kb/HT3964
    Whoops you already did that.
    Hardware Test then
    https://support.apple.com/kb/ht1509
    Read more info here
    https://discussions.apple.com/message/16276201#16276201

  • Dead Imac (need some help)

    Looking for advice or help.
    My new 233mghz intel 20" iMac has died. It has 2 gigs of memory that was installed by Apple and a 500 gig hard drive. When I verify the disk I get 2 errors, "volume bit map needs minor repair" and "error, underlying task reported the following error, Failure to exit". Yet when I try to repair it, disk utility says "no repair needed".
    When I ran the hardware test I received this error code:
    4MEM/1/40000000:04023B44.
    On the advice of Apple tech support I tried to reinstall the system software. That does not work, the iMac either experiences a kernal panic or the install fails.
    Anyone out there seen these problems before? Are the hardware error codes available somewhere. This is essentially a brand new machine.
    I am hoping this will be something I can fix at home as the nearest Apple repair center is over 100 miles away.
    Thanks for any help with this.
    Joe

    Intel-based iMac: Installing and replacing memory (RAM)

  • Late 2006 24" imac - broken sata connector on logic board

    How to fix broken sata port on logic board? It snapped off, apparently it wasn't soldered on very securely. Now I can only boot my machine with external usb drive. Help!

    Hi Aaron
    Bummer, I only see 4 options.
    1. Continue to run from an External HD, FireWire 400 is faster than USB.
    2. Find someone with the tools and skill to re-solder a connector back onto the logic board.
    +(problem is, not to many folks can or will, because it's nearly impossibly)+
    3. Buy a new Logic Board for $600+ > http://www.welovemacs.com/apim242inco26.html
    +(problem is, that the iMac isn't worth $600)+
    4. Buy a New or Refurbished iMac.
    http://store.apple.com/us/browse/home/shop_mac/family/imac?mco=MTcyMTgwNTQ
    http://store.apple.com/us/browse/home/specialdeals/mac?mco=OTY2ODY3Nw
    Personally I'd put my money on #4, instead of spending another dime on a 4 year old machine that also needs a Graphic's Chip and who knows what else.
    Dennis

  • Brand New 2007 24'' IMac need some opinions please

    Hi,
    I have a 24' I Mac that is a 2007,,,, it was only used for 1 month then put into storage do to a move,,,, I just got it out of storage and set back up again. It only has 1MB of Ram, and I would like to possibly get it upgraded to the 3MB, anyone know how much this would cost, and if it is worth it to do ??? Also what other suggestions for upgrades that can be done to this system to bring it more up to date. This computer is just about brand new. like I said was used for approx 3 weeks and thats it. I read MB or is it GB of Ram is the most this system will take, id this true or can I get more ???
          Thank You
          MWA1024

    A 4GB kit will cost you just under $60
    see > OWC Apple iMac Memory Upgrades
    or > Computer memory upgrades for Apple iMac at Crucial.com
    Plus you could/should upgrade to Snow Leopard. Problem is Apple no longer sell Snow Leopard thru the Apple Store, so you will need to call Apple Support and ask for a 10.6 Upgrade DVD.

  • I have a macbook pro core 2 duo (late 2006) that i need to install a OS on (It doesn't have one at all).

    I spoke with an Apple worker and they said snow leopard would work but he didnt know if the upgrade disk would work or not. I need help with this. I will need 5 copies so i hope i can spend 20 or 30 instead of 600. Thanks. Email is ******
    <Edited by Host>

    See if your computer is compatible with Lion. The license allows you to install it on computers you own.
    Computer Compatibility - Lion                       Lion               
    Check to make sure your applications are compatible. PowerPC applications are no longer supported after 10.6.      
    Application Compatibility
    Applications Compatibility (2)
    If you buy the Snow Leopard family pack, you can install it on 5 computers in your family. You might have to look at Amazon and other places to find it.
    http://wiki.answers.com/Q/How_many_computers_can_you_install_snow_leopard_on

  • IMac (Late 2006) Stalls with EFI 1.2 and Leopard

    A few days ago, I installed both the iMac 1.2 EFI Firmware update and Leopard on my late 2006 20" iMac. Since then, I've seen random momentary stalls throughout the system.
    It sometimes happens while scrolling a web page, displaying a sheet, opening a stack, browsing CoverFlow, and so on. I don't know how to intentionally recreate it, it just seems to happen. It often (always?) seems to coincide with some disk activity.
    I don't remember this behavior on the same hardware in the past, so either it's something with the firmware update or Leopard. Has anyone seen anything else like this?
    Thanks in advance.

    Some people reported various bugs after installing the firmware update. Shutting it off and turning it back was all that was needed to fix the bugs.

  • IMac Late 2006 GPU crashing

    I have a late 2006 24" iMac described by my "product" thing. If I do something graphics related like games, Exposé with a LOT of windows, or even sometimes the Dock, I get garbage all over my screen like lines and blocks. Sometimes I can stop it, but I usually have to restart. The computer functions normally besides the graphics (I connected with SSH to it).
    Two questions: Can it be due to overheating? It seems to do it more on hot days, but I haven't really tested. It is currently at 108˚F in a fairly cool room (65˚F?).
    Secondly, if I need to replace it, is it possible, or is the graphics card soldered onto the motherboard?

    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    10.4 instructions...
    Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
    If using Wifi/Airport...
    Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
    in Network>TCP/IP>DNS Servers:, for that Interface... then add these numbers...
    208.67.222.222
    208.67.220.220
    (There may be better or faster DNS numbers in your area, but these should be a good test).
    Click OK.

  • IMac, late 2006, runs extremely slowly, hard drive grinding

    Besides the RAM shortage (upgrade is in the mail) what else id wrong here?
    EtreCheck version: 2.1.5 (108)
    Report generated December 29, 2014 3:42:24 PM EST
    Click the [Support] links for help with non-Apple products.
    Click the [Details] links for more information about that line.
    Click the [Adware] links for help removing adware.
    Hardware Information: ℹ️
        iMac (20-inch Late 2006) (Verified)
        iMac - model: iMac5,1
        1 2.16 GHz Intel Core 2 Duo CPU: 2-core
        2 GB RAM
            BANK 0/DIMM0
                1 GB DDR2 SDRAM 667 MHz ok
            BANK 1/DIMM1
                1 GB DDR2 SDRAM 667 MHz ok
        Bluetooth: Old - Handoff/Airdrop2 not supported
        Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
        ATY,RadeonX1600 - VRAM: 256 MB
            iMac 1680 x 1050
            spdisplays_display_connector
    System Software: ℹ️
        Mac OS X 10.6.8 (10K549) - Uptime: 7:52:35
    Disk Information: ℹ️
        ST3250824AS  Q disk0 : (232.89 GB)
            - (disk0s1) <not mounted> : 210 MB
            Mac HD New (disk0s2) / : 249.72 GB (45.33 GB free)
    USB Information: ℹ️
        Micron Built-in iSight
        Apple Inc. Bluetooth USB Host Controller
        Apple Computer, Inc. IR Receiver
    Problem System Launch Daemons: ℹ️
        [not loaded]    org.samba.winbindd.plist [Support]
    Launch Agents: ℹ️
        [loaded]    com.hp.help.tocgenerator.plist [Support]
        [not loaded]    com.trusteer.rapport.rapportd.plist [Support]
    Launch Daemons: ℹ️
        [loaded]    com.adobe.fpsaud.plist [Support]
        [running]    com.trusteer.rooks.rooksd.plist [Support]
    User Launch Agents: ℹ️
        [failed]    com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist [Details]
        [loaded]    com.google.keystone.agent.plist [Support]
        [not loaded]    com.spotify.webhelper.plist [Support]
    User Login Items: ℹ️
        iTunesHelper    ApplicationHidden (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
        Dropbox    Application (/Applications/Dropbox.app)
        EPSON Scanner Monitor    Application (/Applications/EPSON Scanner Monitor.app)
    Internet Plug-ins: ℹ️
        Flip4Mac WMV Plugin: Version: 2.4.4.2 [Support]
        FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
        JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Check version
        Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
        AdobePDFViewer: Version: 8.3.1 [Support]
        QuickTime Plugin: Version: 7.6.6
        WidevineMediaOptimizer: Version: 6.0.0.12757 - SDK 10.7 [Support]
        Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Support]
        iPhotoPhotocast: Version: 6.0
    Safari Extensions: ℹ️
        Disconnect [Installed]
        Disconnect Private Search [Installed]
    Audio Plug-ins: ℹ️
        iSightAudio: Version: 7.6.6
    3rd Party Preference Panes: ℹ️
        Flash Player  [Support]
        Flip4Mac WMV  [Support]
        Trusteer Endpoint Protection  [Support]
    Time Machine: ℹ️
        Time Machine information requires OS X 10.7 "Lion" or later.
    Top Processes by CPU: ℹ️
           107%    WebProcess
             4%    Safari
             2%    PluginProcess
             2%    WindowServer
             0%    ps
    Top Processes by Memory: ℹ️
        1.02 GB    WebProcess
        150 MB    firefox
        140 MB    PluginProcess
        60 MB    Safari
        34 MB    Finder
    Virtual Memory Information: ℹ️
        128 MB    Free RAM
        1.35 GB    Active RAM
        461 MB    Inactive RAM
        207 MB    Wired RAM
        3.72 GB    Page-ins
        2.52 GB    Page-outs
    Diagnostics Information: ℹ️
        Dec 29, 2014, 07:50:36 AM    Self test - passed

    One thing to realize is that the "Webprocess" consuming mass qualities of CPU will come and go depending on the pages you are browsing. It shouldn't do that high CPU constantly only periodically. Some simple pages will take very little, very complex pages with lots of images and flash and ads and other misc stuff can make the CPU usage soar. But that's hard/impossible to predict, so just keep an eye on it and you'll get a feel for pages you might want to avoid and pages that are no big deal to process.
    good luck...

  • 24" iMac (Late 2006) Cannot Display 1080p on External HDTV

    Hello,
    I've been trying to figure out if it's possible to connect my Samsung LN40A550 40" TV (http://www.samsung.com/us/consumer/detail/detail.do?group=televisions&type=telev isions&subtype=lcdtv&model_cd=LN40A550P3FXZA) to my Late 2006 24" iMac at 1080p resolution. Currently, I'm using Extended Desktop mode with my iMac running 1920x1200 but the Display settings only lets me change the resolution on the TV to a maximum of 1080i. I've connected the TV to my iMac with a miniDVI-to-DVI adapter and then a DVI-to-HDMI cable.
    Here are my iMac's tech specs: http://support.apple.com/kb/SP28
    Here is a KB article about the iMac's external display port: http://support.apple.com/kb/TA23844?viewlocale=en_US
    Neither of these articles has said explicitly whether or not it is possible for me to output 1080p to my TV from my iMac. Do I need to use different cabling? I've tried reducing the resolution of the iMac to see if it was a video card restriction, but I still could not increase the TV's resolution.
    I did notice that the newer iMac's specs say that they can output at 1080p: http://www.apple.com/imac/specs/
    Perhaps my iMac just doesn't support external resolutions that high? So I looked up the video card (NVIDIA GeForce 7300GT - http://www.nvidia.com/page/geforce_7300.html) and it does not appear to say whether or not it can handle two displays at 1920x1200. Under the "Advanced Display Functionality" heading it says:
    * Dual integrated 400MHz RAMDACs for analog display resolutions up to and including 2048x1536 at 85Hz
    * Dual-link DVI capability to drive the industry's largest and highest resolution digital flat panel displays up to 2560x16001
    * Integrated HDTV encoder provides analog TV-output (Component/Composite/S-Video) up to 1080i resolution
    Any help figuring out how to connect my TV to my iMac at 1080p would be greatly appreciated!
    Cheers!
    -Aaron

    hey there cooperaa & welcome to Discussions.
    i didn't see anything in the fullspecs that said your TV does 1080p, just that it does 1920x1080. also, since 1080p was a fairly new "standard" for video(Blu-ray/HD-DVD) when your Mac was built, a 1920x1080 progressive output was possibly not included. i have an early 2006 17" iMac connected to my 42" HDTV over DVI>HDMI & i can get 1920x1080i, which is the highest rez my TV will accept & i use this iMac as my DVD player(along w/ an optical cable for audio) & have not noticed anything "ugly" w/ the picture as i have de-interlace selected on the DVD player(a standard DVD is 720x480). since Apple doesn't include a Blu-ray player/recorder in any of their machines what will you watch that will be in 1080p? generally if your TV does the higher rez, it will scale the rez to fit your settings--ie. a 1920x1080i broadcast on a 1280x720p TV will scale down to the TV's native rez as well a 1280x720p broadcast will be scaled up to 1920x1080i if that's the native rez.
    good luck.

  • Completely unusable Late 2006 iMac

    I've been scouring the discussion boards for some time due to an issue I've been having with my Late 2006 17" iMac Core 2 Duo. It seems as if I'm not the only one having this issue. I've been having random artifacts and distortions appearing on the screen. I've taken screenshots and they appear in them aswell as when using VNC. I was hoping that snow leopard would fix the issue because I thought it was software issue, although its even worse now. Not only are these random glitches showing up on the screen, the computer is barely usable. For example, last night I turned it on to stream some music to my living room airport express, yet it completely froze and I had to hold down the power button and shut it off. It happened again after the restart.
    I took it to the apple store and the "genius" had the audacity to tell me to "buy a new machine." Why? I have an older macbook pro which is not nearly as fast as my iMac but it works fine. I've converted literally dozens of friends and family to macs and iphones and its embarrassing because I have an unusable brick on my desk. What is my next plan of action? I'm certainly not willing to spend $800+ to have this fixed when it is clearly not my fault. I understand it is out of warranty but this is not a rare issue as you can see by this discussion board.

    Found this on "intel imac with bad logic board" discussion from Bodomann:
    *"Following up on my previous posting regarding my son's late model 2006 iMac that required a $900 logic board replacement:*
    *Turns out the problem is apparently related to a bad CPU temp sensor. I installed 'iMac Fan Control' (Google it) which reported the CPU temp always at 32 degrees Fahrenheit (obviously incorrect). The same software allowed me to adjust the CPU fan manually. After multiple trials I set the CPU speed to 2800RPM after which the system would run forever - never freezing with the dreaded grey box 'reboot me' screen. I tried several times reverting the software to default speeds and the system would always crash within 10 minutes. "*
    I downloaded free Fan Control 1.2 for Imac from Derman Enterprises and cranked up all three fan speeds; 2000 rpm on CPU and 2500 rpm on hard drive, which was running warm. Horizontal lines gone from screen (so far), no color artifacts and no crashes yet. I may have a real computer back! Hope Apple checks this out- I will keep spreading the word if it keeps working!
    Many thanks to Bodomann!!!

  • IMac late 2006 no wifi detected

    I am new to the Mac world other than the basics and I came across a late 2006 20" iMac last week. After installing the only OS I had which is Snow Leopard, I found everything works great on this system except the original wifi card it came with which is after researching a bcm94321 card. Airport utility does not detect it and I have a few other items Ive tried installing but airport utility doesnt detect them either... Any help would be appreciated as I am clueless on how to even troubleshoot this other than just replacing the card. Thanks in advance.
    Preferences

    Hardware repairs are way out of our league around here as most Mac's are not user servicable.
    Try iFixit and/or OtherWorld Computing.

  • Imac late 2006 has two big white bars on the screen.

    Hello,
         I have a late 2006 intel imac and it also has the apparently extremely common vertical white bars on the screen.
    They have the same size, about a twelveth of the whole screen, and are spaced by a well functioning bar of exactly the same size. So i thought this could be a problem with the connectors, and i wondered, is there any connector inside the imac that has 12 pins?
    P.S.: I'm trying to fix this myself because i took it to an apple authorized repair center (which is the closest we have in Portugal to a real Apple repair center), and they said it would be 550€, a ridiculous amount of money, since the screen costs something like 150€, and they ended up charging me 50€ just for letting it stay the night since they didn't even open it.
    I have been an extremely loyal customer and am extremely disappointed in Apple for not replacing this screens for free, since it's clearly a manufacturing problem.

    You are just better off saving up your money to buy a new iMac.
    Late 2006 iMac graphics problem, system freezes
    http://www.youtube.com/watch?v=3j-tZ_v1aCc   <<< click here.

Maybe you are looking for