My Linksys E1500 is Dead? Internet LED Doesn't Light Up

My problem is that when I connect the internet (yellow) cable to the linksys router, the LED notification in my modem turns off. I got internet connection if I won't use the router. But I needed the router, but it is not usable already. In my theory, I think there are parts inside the router that have been damaged. Because it seems that the internet cable is not plugged, even though I plugged it already. I've done many things already but still it didn't work. Can you please help me?

Try to use another cable and check if the internet led will light up. Try connecting the modem to the Ethernet ports as well for isolation. If you will get the same thing, do a hard reset on the router – push and hold the reset button on the router using a pin or a paper clip for 30 seconds then power the router off for another 30 seconds. Check the lights then. You can also do a loopback test – connect one end of the Ethernet cable to the internet port and the other end to any of the Ethernet ports. Check then if both ports will light up. If the internet led will still not light up then it’s possible that the hardware is defective.

Similar Messages

  • My FP-TC-120's ready LED doesn't light up suddenly

    Hi,
           My FP-TC-120's ready LED doesn't light up suddenly, and before that the situation of erratic reading happened sometimes, does anybody know the possible reason? what am I supposed to do now? my fieldpoint controller is FP-2000, and the other three modules are AI-110, AO-200 and RLY-422.
          I expect any reply for this problem.
    thank you!
    yi

    Hi Yi,
    I searched the community and found a good thread on this, please take a look at it.
    Thanks and have a great day.

  • IMAC connected to Mbox 2 - USB LED doesn't light up - Please help!

    Pretty new to all of this. I just bought a new IMAC intel core duo and Mbox 2. I connected the Mbox 2 to the USB port and the LED didn't light up.. I disconnected it and tried again...same thing. I restarted the IMAC and connected the Mbox 2 again...still nothing. I went to system preferences and clicked on the Mbox 2 and it said "You cannot open digidesign Mbox 2 preferences pane on this computer. Contact the developerof this software for a newer version"....needless to say I'm lost now. Can someone point me in the right direction???
    IMAC   Mac OS X (10.4)  

    Try to use another cable and check if the internet led will light up. Try connecting the modem to the Ethernet ports as well for isolation. If you will get the same thing, do a hard reset on the router – push and hold the reset button on the router using a pin or a paper clip for 30 seconds then power the router off for another 30 seconds. Check the lights then. You can also do a loopback test – connect one end of the Ethernet cable to the internet port and the other end to any of the Ethernet ports. Check then if both ports will light up. If the internet led will still not light up then it’s possible that the hardware is defective.

  • Just a little reassurance..DSL modem Internet LED does not light

    After installing a WRT54GL between my computer and a Speedstream 5100 ADSL modem, everything seems to work, except that now only three of the normal four LEDs are illuminated on the modem.
    The normal four are: Power, Ethernet, DSL, and Internet.  After installing the router, only the first three LEDs now stay illuminated. But, I am not denied internet or email (Windows Vista). Does this seem normal?

    After installing the router if the Internet light on router is blinking…it shows the incoming & outgoing data….so blinking of internet light is proper connection from modem to router.

  • Is my ISP blocking ICMP on the WAN side? Linksys E1500 on Comcast Cable

    Hi-
    Device: Linksys E1500 - firmware: 1.0.01
    I've got a static IP setup for a small remote office and want to keep tabs on their internet connection by pinging it via a monitoring program we use. However, the router seems to not responding to ICMP.
    - Filter Anonymous Internet Requests is unchecked.
    - I've verified that the Static IP is correct.
    - I've tried pinging from several remote locations on different connections, with no avail.
    I can't seem to figure out why i can't ping this device. I just want to make sure there isn't a setting in the wireless router that is preventing echo replies.
    The only other thing i can assume is that Comcast is filtering ICMP on their side of the WAN connection.
    EDIT: Here's a traceroute from my PC to the WAN side of the Linksys....
    Tracing route to 50-194-XXX-XXX-static.hfc.comcastbusiness.net [50.194.XXX.XXX]
    over a maximum of 30 hops:
      1    <1 ms    <1 ms    <1 ms  172.25.2.1
      2     6 ms    16 ms     6 ms  10.0.0.5
      3     9 ms     8 ms     8 ms  10.0.0.1
      4     7 ms     7 ms     7 ms  10.0.0.2
      5     8 ms     7 ms     7 ms  ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX]
      6     7 ms     7 ms     7 ms  ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX]
      7     7 ms     7 ms     7 ms  gi142.5.cr1.irvnca.telepacific.net [65.60.126.97]
      8    10 ms    16 ms     9 ms  so-0-1-0.ar2.sna1.gblx.net [64.214.146.65]
      9     9 ms     9 ms     9 ms  po3-40g.ar4.lax2.gblx.net [67.17.107.82]
     10    21 ms    11 ms    12 ms  te-0-0-0-7-cr01.losangeles.ca.ibone.comcast.net[66.208.233.201]
     11    29 ms    27 ms    27 ms  pos-0-4-0-0-cr01.santateresa.tx.ibone.comcast.net [68.86.86.18]
     12    42 ms    47 ms    52 ms  he-0-12-0-0-cr01.denverqwest.co.ibone.comcast.net [68.86.89.53]
     13    54 ms    47 ms    47 ms  he-0-6-0-0-ar02.denver.co.denver.comcast.net [68.86.94.158]
     14    43 ms    43 ms    43 ms  te-8-3-ur09.denver.co.denver.comcast.net [68.86.103.2]
     15    62 ms    59 ms    54 ms  te-17-10-cdn22.denver.co.denver.comcast.net [68.85.221.110]
     16    56 ms    54 ms    69 ms  c-174-51-179-19.hsd1.co.comcast.net [174.51.179.19]
     17     *        *        *     Request timed out.
     18     *        *        *     Request timed out.
     19     *        *        *     Request timed out.
     20     *        *        *     Request timed out.
     21     *        *        *     Request timed out.
     22     *        *        *     Request timed out.
     23     *        *        *     Request timed out.
     24     *        *        *     Request timed out.
     25     *        *        *     Request timed out.
     26     *        *        *     Request timed out.
     27     *        *        *     Request timed out.
     28     *        *        *     Request timed out.
     29     *        *        *     Request timed out.
     30     *        *        *     Request timed out.
    Trace complete.
    Any help verifying that i have the Linksys setup correctly would be greatly appreciated.
    -Aaron

    Actually, as I understand it
    Since he is seeing the following, I'd say its working fine
      1    <1 ms    <1 ms    <1 ms  172.25.2.1
      2     6 ms    16 ms     6 ms  10.0.0.5
      3     9 ms     8 ms     8 ms  10.0.0.1
      4     7 ms     7 ms     7 ms  10.0.0.2
      5     8 ms     7 ms     7 ms  ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX]
      6     7 ms     7 ms     7 ms  ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX]
      7     7 ms     7 ms     7 ms  gi142.5.cr1.irvnca.telepacific.net [65.60.126.97]
      8    10 ms    16 ms     9 ms  so-0-1-0.ar2.sna1.gblx.net [64.214.146.65]
      9     9 ms     9 ms     9 ms  po3-40g.ar4.lax2.gblx.net [67.17.107.82]
    10    21 ms    11 ms    12 ms  te-0-0-0-7-cr01.losangeles.ca.ibone.comcast.net[66.208.233.201]
    11    29 ms    27 ms    27 ms  pos-0-4-0-0-cr01.santateresa.tx.ibone.comcast.net [68.86.86.18]
    12    42 ms    47 ms    52 ms  he-0-12-0-0-cr01.denverqwest.co.ibone.comcast.net [68.86.89.53]
    13    54 ms    47 ms    47 ms  he-0-6-0-0-ar02.denver.co.denver.comcast.net [68.86.94.158]
    14    43 ms    43 ms    43 ms  te-8-3-ur09.denver.co.denver.comcast.net [68.86.103.2]
    15    62 ms    59 ms    54 ms  te-17-10-cdn22.denver.co.denver.comcast.net [68.85.221.110]
    16    56 ms    54 ms    69 ms  c-174-51-179-19.hsd1.co.comcast.net [174.51.179.19]
    As I understand it the following
     17     *        *        *     Request timed out.
    18     *        *        *     Request timed out.
    19     *        *        *     Request timed out.
    20     *        *        *     Request timed out.
    21     *        *        *     Request timed out.
    22     *        *        *     Request timed out.
    23     *        *        *     Request timed out.
    24     *        *        *     Request timed out.
    25     *        *        *     Request timed out.
    26     *        *        *     Request timed out.
    27     *        *        *     Request timed out.
    28     *        *        *     Request timed out.
    29     *        *        *     Request timed out.
    30     *        *        *     Request timed out.
    Is actually the networks there are not allowing the trace data to be returned
    which is normal for a number of reasons

  • WRT54G2 3 and Internet LED blinking

    I have a WRT54G2 v1 router.
    When power is attached the 3 and Internet LED are blinking. None of the other LED's are blinking.
    No other cables are attached to the router, just the power cable.
    Downloaded the latest firmware, set a static IP address on the laptop, attached a ethernet cable from the laptop to the router but cannot ping or get access to the router to update the firmware.
    Need suggestions as to what the 3 and Internet LED blinking means and what else I can try.

    Here is the latest and this will be done...
    I got back online (without the router, just direct connect to ISP with modem). Did a online CHAT at linksys.com/support. I asked the individual if the blinking LEDs were some sort of diagnostic code. He had never or could not find anything that suggested the blinking 3 and internet LEDs meant anything.
    So the Individual stepped me though the following (common set of steps with all I will assume.)
    No other cables are plugged into any of the router ports.I tried to reset the router. Held the reset button for 30 seconds... no change in which LEDs were blinking (still the 3 port and internet LEDs). Nothing happens with the power led.
    Held the reset for 60 seconds... no change.
    Held the reset button and plugged in the power supply, waited 30 seconds to release... no change.
    Held the reset button and plugged in the power supply, waited 60 seconds to release... no change.
    Asked me to plug in another power supply... could not do that, the router only came with one power supply.
    Asked me to connect router to a computer, step through process to setup static ip address.. attempt to ping router... nothing (was not getting a link light on the computer network card.)
    Finally said I would have to call customer service to get a RMA.
    Called customer service, was told to access the linksys.com/support and use the warranty online system to request a RMA.
    Went online, got to the RMA request, wanted a Case #. No one gave me one, had to call back and get one, they had me talk with a technician. Support person wanted me to go through the same process that I had gone through the night before.
    Explained that went though it already, they had to talk with a supervisor.
    After several minutes came back and gave me a case #.
    Back to the online RMA request - case # was not valid.
    Called customer service back again, after another discussion, was given a new case #. This person did stay online and waited as I went through each step in the online RMA process.
    SO long story... unit shipped back to linksys, replacement being shipped to me.
    (Mod note: Edited for guideline compliance. Thank you for your understanding.)
    Message Edited by giantherockstar on 08-26-2008 10:30 AM

  • Linksys E1500 Access Point?

    How do i setup my Linksys E1500 router as an access point? I have a main router upstairs but the signal is weak in the basement. How do i configure this router as an access point for internet?

    Cascading the e1500 from an existing non-Cisco / Linksys router CAN be done. Here are the steps (for all, and for self):
    1. Reset: http://homekb.cisco.com/Cisco2/ukp.aspx?pid=80&vw=1&articleid=4008
    2. Setup Bridge Mode: http://homekb.cisco.com/Cisco2/ukp.aspx?pid=80&vw=1&articleid=24583
    Just did this from a Qwest / CenturyLink / Actiontec Q1000, working fine.

  • How to make AE work with Linksys E1500 Router

    I use Mac OS X 10.7.5
    I want to use my AirPort Express (Serial # C86L11G8DV2R) as an extender to extend my WiFi network at home, but doesn't work because to set up either my Linksys E1500 Router or AirPort Express (?)
    Can someone explain how I can set up my Linksys E1500 Router to make it compatible with AirPort Express?
    Thanks a lot!

    You can use an Express to "wirelessly extend" a wireless network created by another Apple AirPort Base Station, but not a third party product.
    You can use the Express as an additional wireless access point. To do that, connect it to your existing router with an Ethernet cable.

  • Cisco Linksys E1500 Wireless Router Issues

    About a month ago, I bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new  router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload 
    Details About Router & Connection
    Its a Linksys E1500  with the capability of up to 6 devices and my IPS is Comcast.

    Make sure to upgrade the router’s firmware if there is a new firmware update available. Try to play around with the router’s wireless settings; use this tool: http://www.metageek.net/products/inssider/ to select the best channel that you can set on your router. With regard to that 300 Mbps of speed, it means that it is the maximum link/card speed that the adapter could get from the router not the actual internet speed. 

  • Internet LED turns Red at a certain time of the day

    I have a customer who last year would lose there internet connection like after 4:30pm each day. I was over there a couple days ago and saw it in action. I noticed that on the Actiontec GT704WG modem all the lights would start blinking and then the Internet LED would turn red with all other still green and then it would connect again for a minute and keep going through that cycle. Already did the reset of modem etc. Even happens when the Cat 5 cable is not plugged in. Could this be a power issue with the modem? Also, the ipconfig settings are fine when this is happening... Anyone have any ideas what the issue is? Thank You

    All of the lights blinking? Would this include the power lights or only the Ethernet and Wireless lights? If it's the lather, it sounds like the computer searching for a way to the Internet using broadcast packets. The DSL light if it's blinking would indicate a loss of sync, and this can turn the Internet light red. Anyhow, if you can clear up what exactly was blinking, we can continue.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • Display replaced...but iSight led doesn't work

    I've a Macbook Pro (June '07) on which i've totally repleaced the display. They (the apple support) have mounted the new MacBook Pro display (Feb '08), that is as the old one, but with only one difference: http://nobi.com/nobilog/archives/001795.html
    Now if i use my integrated iSight the green led doesn't turn on. Is this an internal cable-connection issue or does the led work just with the new MacBook Pros?

    Hello Marco
    Try the suggestions in Apple's How to Troubleshoot iSight.
    Regardless of whether you can see a green led, if your built-in iSight does not work (meaning you can see a picture from your iSight) with any app in any user account, the repair job is not finished. Contact the people who worked on your Mac and ask them to correct the problem or credit you for what you paid for the part of the work that was not completed.
    If your iSight works but you cannot see the green LED, you can decide whether a return trip to get the led working is worthwhile to you. I probably wouldn't bother, but you might want to have it made right. The most meaningful reason I can imagine to take it back ONLY for an LED fix is that a working LED might be important to someone to whom you consider selling your Mac at some future time.
    EZ Jim
    PowerBook 1.67 GHz w/Mac OS X (10.4.11) G5 DP 1.8 w/Mac OS X (10.5.2)  External iSight

  • Lumia 920 - internet sharing doesn't work: Connect...

    Hello all,
    I'm experiencing a serious problem with the lumia 920. It seems impossible to share my internet connection. Something I normally use for several hours a day. If this problem can't be fixed soon, ill be forced to swithc back to iphone or htc.
    Problem description:
    When turning "internet sharing" on:
    Connection not shared - There is no cellular data connection to share right now. Check your cellular settings and signal, and try again.
    Important remarks
    Belgium - cellular provider is Mobistar
    I can browse, sync email, etc over the provider's network ans send and receive MMS.
     Provider does not block internet sharing. Have always used this.
    OS Version 8.0.10211.204
    Firmware revision: 1232.5957.1308.0002
    Access point :
     Nokia Access Point version:3.4.1.7 - db 2.0.0.100 - lib 1.2.0.7
     The default access point provided in the Nokia Access Point app does not work: can't even browse.
     Using a manually added APN:
     Data type (default / LTE) tried both. Everything keeps working - except internet sharing...
     APN pro.web.be  (for professional subscribers)
    MMS APN mms.be
    MMSC address: https://mmsc.mobistar.be
    What have i tried to remedy the situatiuon?
     updated the Nokia Access Point app
     changed language to spanisch using OTA update (silly, but read on a forum this might help)
     soft reset of the phone (often!)
     deleted the manually created access point
     Hard reset of my phone
    I'm interested, of course, in any tips to solve this serieus bug / issue / problem.
    (my best guess is that Nokia tries to help their customers with the Access point app, but fails to do so).
    Please, if any of you experience the same problem please respond to this post so we can get an idea about how big of a problem this is.

    Hi,
    I had the same problem. But I let it go after weeks of corresponding with Mobistar.
    Yesterday I went to a Mobistar shop, the guy tried lots of thing I already tried (different apn's, ...).
    Then he told me the it's a problem with business clients. They have to use the apn web.pro.be, where internet sharing doesn't work (he doesn't know why).
    But, that if I call to Mobistar and ask to activate apn mworld.be on my telephone number, it should work.
    Today I called Mobistar Business (you can find the helpdesk number on your invoices), asked to activate mworld.be to have internet sharing access on a windows phone.
    Half an hour later, using mworld.be as apn i have internet access, and I can share my internet connection.
    regards,
    Stijn

  • Sirius Internet Radio doesn't work after Snow Leopard

    Sirius Internet Radio doesn't work after I installed Snow Leopard. It works on my Firefox. I emptied the cache on my Safari, but still nothing. Any solutions?

    The reason why Sirius Radio online won't work with Safari anymore is because Sirius radio online is only supported by a 32-bit browser. Snow Leopard and all its applications are 64-bit. The best solution is to use firefox. If you still insist on using safari..... Go to adobe.com reinstall adobe flash player. Install/update Flip4Mac. Go to setting for Flip4Mac and check off all the options under the browser tab. Then when you go into Sirius Radio online, you will get an error message, just click okay. Then when you click a station, a quicktime player will come up and you will be able to listen to sirius online radio.
    [email protected]

  • HDD LED doesn't work with SATA?

    I just built this system last week and installed a Maxtor 160GB SATA drive and the led on the case doesn't light up when the HDD is in use. Is this a board problem or SATA problem?

    Please go here. https://forum-en.msi.com/index.php?threadid=41020&sid=

  • LED on the adapter connector doesn't light up

    Sometimes The LED on the adapter connector doesn't light up when attached to the computer and computer doesn't sharge. When I eject it and inverse it, it works! sometimes it doesn't work in both sides. Whats the problem?
    My Macbook pro model is retina 2013 me864.

    Try a different charger. If your computer is under warranty so is the charger and Apple will replace it.

Maybe you are looking for

  • IWorks 08 and Snow Leopard

    I've just upgraded to Snow Leopard and now seem unable to use Page or Numbers. When I open an existing document or spreadsheet the text seems to have turned white and the whole spreadsheet has a purple tint to it. When I try to create a new document

  • Iphone 5 lte only 2 bars

    I have the new iPhone 5, I found out that lte signal has only 2 or 3 bars, but if I turn the lte off, 3G has 5 full bars, in the same spot. I don't know if it's a software issue or I have a bad phone. I'm on verizon network in Chicago. I wonder if ot

  • Time display in iCal

    I recently discovered that I can have the time of each event in iCal appear in the month view on my Mac.  I would like to have the same setup on my iPad but don't see a way to do it.   Can anybody help?

  • More about pop ups - epic fail

    So, yeah, I'm working on this portfolio site, and I'm trying to nest these pop ups inside a scrollpane ... the debugger isn't finding anything wrong with the code, but it's not working at all. Even my rollovers are acting weird. I'm no expert, but I'

  • Price List Lines doesn't shown up

    All of sudden the price list lines are doesn't shown up on the price list form, any idea? Srini C