My Mac book pro won't print to canon IR-ADV C5035 wirelessly but my I pad will

My Mac book pro won't print to canon IR-ADV C5035 wirelessly but my I pad will

It is very difficult to offer troubleshooting suggestions when the "os version" you are using is unknown as each os has their own troubleshooting solutions.
Please describe in detail all you have attempted to do in order to resolve the issue.  Contacted Canon's tech support for instance?

Similar Messages

  • Mac Book Pro Won't Print to Epson CX8400

    We have a new Mac Book Pro, 17 inch, 2.66 GHz, 4GB, Mac OS 10.5.6. We set up my son's Epson CX8400 All-In-One printer. All the drivers loaded without issue. When we try to print, the printer feeds paper until there are no more sheets in the feeder and nothing is printed.

    Have you tried updating the drivers from Epson's website?
    here is the link:
    http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=90342&prodoid=63069 506&infoType=Downloads&platform=Macintosh

  • Mac book pro won't turn on mavericks

    I successfully upgraded to Mavericks 2 weeks ago and have been having sporadic problems.
    Today my Mac Book Pro 15" 2012 edition (not retina) turned off while I was using it and will not turn back on.
    Anyone have a similiar problem?

    Hello ColeSF,
    It sounds like you have been using OS X 10.9 for a bit and suddenly in the middle of using it, the computer shut down will not turn back on. I was researching what could be causing this to happen and found this article that should help you troubleshoot the issue named:
    Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/TS1367
    Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
    If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
    Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
    Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
    If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
    MacBook Pro: How to remove or install memory
    MacBook: How to remove or install memory
    Mac Pro: How to remove or install memory
    Mac mini: How to remove or install memory
    iMac (27-inch, Late 2012): Installing or replacing memory
    iMac: How to remove or install memory
    Reset the SMC.
    If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • How to connect my mac book pro to network printer Canon IR 2010f?

    I'm desperate to know how to connect my Mac book Pro to network printer Canon IR 2010f. This printer has an independent system, therefore, no need a PC to be on, in order to print. But this printer is a network printer. Help me please.

    The Canon UFR2 v2.20 driver for Mac OS X does not list the iR2010F as a supported model. The same is so for the Canon PS driver so I therefore believe this model is PCL5e only.
    What you should do is open Safari and type the IP address of the iR2010F. This will connect to the internal web page of the copier and from the provided pages you should be able to see what printer languages are supported.
    If it only lists PCL then you will be able to print to this copier using the Generic PCL driver included with 10.6.
    So if you open Print & Fax, click + to add and then select IP > LPD for the protocol you can then enter the IP address of the iR2010F and leave the queue name blank. For the name you can change that to iR1020F and for the Print Using, select Generic PCL Laser Printer.
    One note with regards to this driver. It is defaulted to 300dpi so you will need to open the print dialog when you do print and change the resolution to 600dpi to get better print quality.

  • Ipad is asking for a passcode which I never installed. iPad is now disabled. Tried syncing to itunes with my mac book pro, won't sync. How do I fix this?

    ipad is asking for a passcode which I never installed. iPad is now disabled. Tried syncing to itunes with my mac book pro, won't sync. How do I fix this?

    Recovery Mode
    1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
    3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
    Note: Data will be lost. You may have to repeat the above many times.

  • My mac book pro won't turn on, My mac book pro won't turn on

    My mac book pro won't turn on, My mac book pro won't turn on

    Go step by step and test.
    http://support.apple.com/kb/TS1365
    Note: Steps 5 and 6
    Step 5
    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".

  • HT201177 My Mac book pro won't re-start. The apple sign stays on for a while, that little circle keeps spinning and nothing happens. After 10 minutes rebooting  the screen turned blue and nothing was on besides the cursor. what should I do? Thanks.

    My Mac book pro won't re-start. The apple sign stays on for a while, that little circle keeps spinning and nothing happens. After 10 minutes rebooting  the screen turned blue and nothing was on. now I just re-tried and lots of pixels came up. what should I do? Thanks anyone.

    My Mac book pro won't re-start. The apple sign stays on for a while, that little circle keeps spinning and nothing happens. After 10 minutes rebooting  the screen turned blue and nothing was on. now I just re-tried and lots of pixels came up. what should I do? Thanks anyone.

  • My Mac book pro won't charge. But the connector is plugged in and shows that its charging but it says it has 0% but if I unplug it it will shut off

    My Mac book pro won't charge. But the connector is plugged in and shows that its charging but it says it has 0% but if I unplug it it will shut off. It's been like this all day but I didn't notice till I turned it on.

    It's either a power adapter issue (not likely) or (more likely) a power supply problem on your MBP. Take the machine into your local Apple Store or an AASP and have them diagnose the problem.
    Good luck,
    Clinton

  • My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

    My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

    Yes if your model MBP has a removable battery.  If it does not: 
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer. 
    Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
    http://support.apple.com/kb/HT3964

  • My Mac book pro won't start! It boots as far as the sign in screen and then everything goes black. Please help.

    My Mac book pro won't start! It boots as far as the sign in screen and then everything goes black. Please help.

    Which model MacBook Pro do you have (e.g., “15-inch Late 2011”) and which version of OS X are you running?
    Clinton

  • Mac book pro won't go pass apple icon screen

    My Mac book pro won't go pass the start up screen. It displays the gray apple and the spinning grey circle. HELP!

    10.7 Lion / 10.8 Mountain Lion
    Repair Disk
    Steps 2 through 8
    http://support.apple.com/kb/PH5836
    Reinstall OS X
    http://support.apple.com/kb/PH10763?viewlocale=en_US
    Additional Steps
    http://support.apple.com/kb/PH10929

  • Old iMac numbers 08, new Mac Book pro won't let me open numbers without converting to Numbers 09

    I bought a new Mac Book Pro and when moving my Numbers and Pages files to the new computer it will not allow me to open the files until I update them to Numbers 09 first.  On my iMac I was running Numbers 08.  Any suggestions how to tackle this issue? 
    Thanks,

    Hi onnygirl,
    Numbers 3 will not open Numbers '08 documents.
    On your iMac, open and then export your Numbers '08 documents to Excel.
    Transfer the Excel documents to your MacBook and they will open in Numbers 3.
    Numbers is not an Excel clone, so there will be some glitches .
    Regards,
    Ian.

  • My Mac Book Pro 13 inch shuts down when I insert some usb on port. It will be dead for few days (no power, can't charge as well, no restarting) and after few days it will work? Any one facing same issue and any solutions please...

    My Mac Book Pro 13 inch shuts down when I insert some usb on port. It will be dead for few days (no power, can't charge as well, no restarting) and after few days it will work? Any one facing same issue and any solutions please...

    Hi ohmghimire,
    Thanks for visiting Apple Support Communities.
    If you're seeing unexpected behavior when using USB devices, try resetting the SMC on your MacBook Pro:
    Resetting the SMC on portables with a battery you should not remove on your own
    Note: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer.
    Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
    You can find the article with these steps here:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/HT3964
    If you still see this behavior after resetting the SMC, or your computer won't turn on, try the steps in this article next:
    Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/ts1367
    Best Regards,
    Jeremy

  • I am using FCP 7.0.3.on my Mac Pro. I bought a new mac book pro and loaded the software on to the lap top but the software is 6.0.3. How do i get the update to the lap top?

    I am using FCP 7.0.3 on my Mac Pro. I bought a new mac book pro and loaded the software on to the lap top but the software is 6.0.3. How do i get the update to the lap top?

    .. and by the way, the jump from FCP 6.0.3 to FCP 7.0 (or higher) isn't an "update"  It's a full version "upgrade" that has to be done using the install discs (or disc images).
    -DH

  • My hard drive crashed on my Mac Book Pro and I just had it replaced yesterday.  After restoring my data, Safari will not open.  The error message I continue to receive is "Safari quit unexpectedly"  Should I just delete the application and download a new?

    My hard drive crashed on my Mac Book Pro and I just had it replaced yesterday.  After restoring my data, Safari will not open.  The error message I continue to receive is "Safari quit unexpectedly"  Should I just delete the application and download a new one?

    http://swcdn.apple.com/content/downloads/37/23/041-5058/lr5tynbldi18zcrqo8a8uq88 rnjushqliu/Safari6Lion.pkg 
    Here you go.....

Maybe you are looking for