My Mac Book will not go past the grey screen

I had my Mac Book Pro at a apple store and they had to reformat the hard driver. Now several weeks later I installed the 2012 turbo tax software and restarted the machine however now I cannot get past the grey screen.
What is wrong with this, they stated the reformat would solve the problem.
Need help

Which os version are you using and is it compatible with your os? 
Mac OS X: Gray screen appears during startup 

Similar Messages

  • I have a Macbook and I left it unplugged. It started up slowly when I plugged it in again, but it seemed fine. Once it started charging I shut it down so it would be easier, but now it will not go past the grey screen with the apple. What do I do?

    I have a Macbook and I left it unplugged. It started up slowly when I plugged it in again, but it seemed fine. Once it started charging I shut it down so it would be easier, but now it will not go past the grey screen with the apple. What do I do?
    I have Snow leopard on my computer, and I tried to do a hard restart as an article suggested, but it did not work. I also tried cleaning out the PRAM.
    The only things I did last night:
    -cleaned the history of Firefox out, including cookies
    -let it unplugged all night
    -plugged it back in the morning, it took a long time to figure itself out, but eventually the time was correct and I got on the internet for a bit
    -shutdown the computer since I was going out and thought it would help the computer charge
    -came back, tried to turn it on, and found that it would not go past the grey screen the apple on it and the spinning wheel even though I left it for 20 minutes or more
    -tried turning it off and on to no avail

    Before doing a reinstall, which may not be needed at this point,
    Try using Disk Utility to do a Disk Repair, as shown in this link, while booted up on your install disk.
    You could have some directory corruption. Let us know what errors Disk Repair reports and if DU was able to repair them. This could just be a start in repairs and you may need a better utility to finish the job.
    Then Repair Permissions.
    No need to report any Permissions errors........we all get them.
       DALE

  • Ibookg4 will not go past the grey screen and will not accept a disc

    my ibook will not go past the grey screen and will not accept a disc

    Have you tried starting up in Safe Mode? If not, I suggest that you give it a try. This will take quite awhile longer than a normal startup because it does a file check and repair of the hard disk.
    If this works you will see your normal desktop. Once completely started up in Safe Mode, try to restart normally, and go to Applications > Utilities > Disk Utility. Click on the top hard drive icon in the left sidebar and note the S.M.A.R.T. status at the bottom right of the pane. What does it say?
    Select the named boot volume in the left sidebar, ("Macintosh HD" unless you've renamed it). What is the hard drive capacity and how much space remains available on it? Repair permissions on it.
    See if you are able to do a little hard drive maintenance to help things out.

  • My MacBook pro will not load past the grey screen with the spinning wheel. What do I do?

    My MacBook will not load past the grey screen with the spinning wheel of death. Anyone have any solutions?

    Invoke Safe Mode by holding down the shift Key as you restart. This will do a Disk Utility "Repair Disk" as it starts up (so it takes a few minutes longer) and then load with minimal extensions loaded, and request your login username and password, even if you normally do not use them to log in.
    Safe Mode runs the screen using simple, unaccelerated commands. Most things are available in Safe Mode, but things that rely on extensions will not be.
    Acomputer that works in Safe Mode, but fails again after you restart, often implicates your extensions and add-ons.

  • Mac book will not boot up,only grey screen with ? on it,Why?

    Why won't my Mac book boot up,start up only grey screen with ? showing?

    That folder with the question mark icon means that the MacBook can't find the boot directory. That can either mean it can't find the hard drive or the Operating System data on the hard drive is somehow corrupted.
    With 10.4, 10.5 or 10.6 put your install DVD into the optical drive (CD/DVD drive) and reboot. Be sure to either use the disc that came with your Mac, or, if you installed a later Mac OS X version from disc, use the newer disc. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option Key until the Install Disk shows up) until the apple shows up. That will force your MacBook to boot from the install DVD in the optical drive.
    Or if you are running 10.7 Lion, 10.8 Mountain Lion or 10.9 Mavericks, boot from the recovery partition (Command +R on boot) and use Disk Utility to repair your OS 10.7, 10.8 or 10.9 partition.
    When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
    If it is, then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions. After repairing use Startup Disk from the same menu to choose your hard drive for restarting from your hard drive.
    If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

  • Laptop will not boot past the grey screen bootup screen

    Hi,
    I have started up my machine today and its displaying the grey screen and is not booting any futher.
    The machine is only 2 Months old, its a :
    2.8GHz Intel Core i7
    8GB 1066MHz DDR3 SDRAM - 2X4GB
    512GB SATA HDD
    SuperDrive 8x (DVD±R DL/DVD±RW/CD-RW)
    MacBook Pro 17-inch Hi-Resolution Antiglare Widescreen Display
    Any ideas?, It was fine yesterday now nothing
    Thanks.
    Ron

    Try this article.
    Mac Os X: Gray Screen appears during startup
    http://support.apple.com/kb/TS2570

  • TS1367 My MacBook Pro will not go past the grey screen with apple logo in the middle

    How do I fix this issue  is there anything I can do

    Hey there Gonzoeg850,
    It sounds like you are unable to boot your computer to your desktop or log in screen. I do not know if you have tried these steps from the article you have up there, but that is exactly where I would start:
    Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/TS1367
    Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
    If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
    Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
    Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
    If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
    MacBook Pro: How to remove or install memory
    MacBook: How to remove or install memory
    Mac Pro: How to remove or install memory
    Mac mini: How to remove or install memory
    iMac (27-inch, Late 2012): Installing or replacing memory
    iMac: How to remove or install memory
    Reset the SMC.
    If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • My macbook pro will not get past the gray screen with the apple logo and a loading bar.

    My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours.  I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck.  Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.

    You didn't say which OS in your tag, but maybe you might find something here.
    http://support.apple.com/kb/TS2570
    http://support.apple.com/kb/PH4191
    http://support.apple.com/kb/PH7213
    http://support.apple.com/kb/HT4125
    http://support.apple.com/kb/HT2213

  • My Imac will not move beyond the Grey Screen with the spirl spinning any ideas

    Recently I rebooted my IMac, it now will not move past the grey screen with the spinning spirl.
    Please help

    Turn off your machine, then power on whilst holding down cmd+alt+p+r until the screen goes off and you hear the chime again.
    Also, what iMac do you have/how old?

  • The dowload of firfox will not move past the run screen

    I have been trying to install Firefox to my desktop. The dowload will not progress past the run screen. There is no set up. I successfully installed on my second computer so I am confused.

    I believe you have Voice Over on:
    You have to tap, then double-tap to select the numbers to enter your passcode.
    Then:
    Press Home.
    Tap Settings. Then double-tap Settings.
    Tap General. Then double-tap General.
    Use three fingers on the screen to scroll to Accessibility.
    Tap Accessibility. Then double-tap Accessibility.
    Tap VoiceOver. Then double-tap VoiceOver.
    Tap "On" next to VoiceOver. Then double-tap "On" to turn it off.

  • Ipod will not got past the home screen

    Help please!!!! When I turn my ipod on, (with a full charge and fresh restore and update) it will not go past the home screen (music, setting, ect). The hold button is off. The click wheel will move the selector up and down, but I can't go any further than that.

    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  It could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore, go into Recovery Mode per the instructions here. You WILL lose your "stuff" with Recovery Mode.

  • HT2173 my iMac will not get past the start screen, after i restarted it after it not being able to upload my photos from my iPhone 4S to iPhoto  app on my iMac bc a visa vas about 3:15 min

    my iMac will not get past the start screen, after i restarted it after it not being able to upload my photos from my iPhone 4S to iPhoto  app on my iMac bc a visa vas about 3:15 min.  What should I do to get my imac past this?

    According to your posted Profile here you are running a PPC based iMac.  This Forum is only for "Intel iMac's", and so to get the expert and correct help you need you should repost your question in the "PPC iMac Forum".
    Hope this helps

  • HT1212 I have no idea why suddenly my iPhone5 will not move past the Password screen; also, a voice describes each button I touch, and ends with "screen locked" (not "phone locked").

    I have no idea why my iPhone5 suddenly will not move past the PW screen; a "voice" identifies each button touched (the Slide button, for example) or the PW buttons, and then ends with "screen locked" (not phone locked).

    I believe you have Voice Over on:
    You have to tap, then double-tap to select the numbers to enter your passcode.
    Then:
    Press Home.
    Tap Settings. Then double-tap Settings.
    Tap General. Then double-tap General.
    Use three fingers on the screen to scroll to Accessibility.
    Tap Accessibility. Then double-tap Accessibility.
    Tap VoiceOver. Then double-tap VoiceOver.
    Tap "On" next to VoiceOver. Then double-tap "On" to turn it off.

  • Satellite L500 will not load past the 'welcome' screen

    Hi,
    My Toshiba Satellite L500 laptop will not load past the 'welcome' screen. The cursor thing just keeps going around and around but won't go to my desktop.
    Last night it went into some temporary profile and it had a message saying 'your other profile cannot load at this time please try again later'
    Any help would be greatly appreciated.
    Thanks,
    Kara

    The error message is not known to me and also searching in google didnt get any hints.
    Possibly your Windows OS is muddled up.
    Did you try to boot Win 7 in safe mode?
    Try this. Restart your notebook, tap the F8 key.
    In advanced boot options choose the option called Safe Mode.
    If the notebook does not allow booting in Safe Mode, try the option Last Good Known Configuration.
    If this didnt help, try Repair my Computer. Here you can choose between different settings.
    The one which could solve this is HDD recovery which helps you to set the notebook to factory settings. But this means also that your HDD would be formatted!
    So be aware of this!

  • The Macbook Pro will not start past the grey Apple logo screen? Any help will be most welcome?

    The Macbook Pro 13, late 2009 will not start past the grey Apple Logo screen?  Any help will be most welcome? Thanks

    Have you tried booting with the install disc that came with your computer?
    Find it and then run Disk Utility to verify your hard drive. If errors are found, try to repair the disk.
    It sounds as if the hard drive might be failing.
    Clinton

Maybe you are looking for

  • Dump while saving the project

    Hi all, System is giving dump while saving the changes in the project. Short text      The current application triggered a termination with a short dump. What happened?      The current application program detected a situation which really      shoul

  • Can I have two separate logins/restricted directories in the same web site?

    Hi, I want to have an admin area where I go against a user table to see if the user has admin rights and a separate area of the web site where regular users need a username and password that is validated against a different table. All the pages in th

  • HDMI audio doesn't output to AV receiver

    - 2013 Mac Book Pro Retina 15 - OSX 10.9.4 - Pioneer SC-1522K receiver - Panasonic AE-8000 projector I have problem with my hdmi audio output to my receiver after upgrading to Mavericks.  If I connect my MBP to the receiver, my receiver will appear a

  • Transporting Process Chain - error  Source system does not exist

    Hi, I tried to transport a local PC by itself (not including its main meta chain) since I have only done modifications in the local PC only. In the PC, there are PSA Processing, ODS Processing, ODS Activation, ABAP Program w/ variants and Infocube Ro

  • Snow Leopard-MacBook Pro

    Just tried to install SL onto my MacBook Pro. Can't be done apparently, does anybody know why? It is one of the previous generations before the current one, running OSX 10.5.8