My MacBook Air, once pressed the power button, comes up with a file containing a question mark. I have tried re-starting it but this logo continues to appear and will not go. I cannot log onto my mac. Any suggestions as to what this is please?
My MacBook Air, once pressed the power button, comes up with a file containing a question mark. I have tried re-starting it but this logo continues to appear and will not go. I cannot log onto my mac. Any suggestions as to what this is please?
You need to reinstall OS X:
Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Similar Messages
-
I have a problem with my MacBook Pro, I pressed the power button and after that the apple noise came and the screen turned blue. What can I do and what happened? pls help & thx btw
You may find this helpful:
http://support.apple.com/kb/PH14061
Ciao. -
Hello
If anyone has any info on downloading Lion would be greatly appreciated. The download is in a constant state of pause. I cannot get it out of the pause phase into active download. Anyone having similar trouble?
thxSee if either of these two things help.
Make sure that you do not have a stalled download in iTunes - a song or podcast .... if you have a download in there that did not finish, complete that one first. Only one thing can download at a time on the iPad so that could be what is causing the problem.
If that doesn't work - sign out of your account, restart the iPad and then sign in again.
Settings>Store>Apple ID. Tap your ID and sign out. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Go back to Settings>Store>Sign in and then try to update again. -
I have MacBook Air late 2011 with encryption enabled the mac froze and I pressed the power button to shut it down but then the gray screen appeared no wheels nothing just gray. I tried all steps but nothing helped. Worse than that only the pram key combination works I cant get the cmd-r or just alt or any combination to work??? Any suggestions would help. Thanks!
P.s. I am on mountain lion with ssd encryption enabled. The mac froze when the internet stopped the one from the cable (I use ethernet usb one) when I turned wifi on it froze. I have disconnected everything when trying the steps except power cable.Boot into Internet Recovery (command-option-R at the startup chime) and try to repair the boot volume in Disk Utility. You will have to unlock the volume before you can do anything with it.
-
Shutting the Macbook by pressing the power button for long
how bad is it for your MacBook Pro to shut it down by pressing the power button for a few seconds rather than by choosing Shut down?
If ever I have to "force" a shutdown in this fashion then I immediately boot up from an external drive or DVd and run either Disk Utility or Disk Warrior to repair the drive's directories, shroudlupe.
It regularly pops up some kind of error after such events, sometimes quite serious ones. It can also corrupt permissions in some circumstances, too, if software which modifies them "on the run' and then sets them back again happens to be in use at the time, so you should do a permissions repair on the next boot, too. The actual nature of problems generated will depend on what was running at the time, what OS background processes were underway, etc etc. It is not really predictable. Doing it once at the wrong time can have serious consequences, while on other occasions you may come away scot free.
Although the impact may not be quite so great since "journalling' was introduced on Macs, I suspect that many of the problems that we see when people update their OS's etc, as well other general operating problems, occur because directories etc haven't been repaired by the user after such events at some time in the past.
At the very least I'd suggest you use a 'Safe Boot" after any such event, and then restart normally. See http://support.apple.com/kb/TS1417 for some alternative approaches to repairing the damage that it is likely to cause.
Are you having trouble shutting down normally, or are you just looking to save time?
Cheers
Rod -
I have frequent instances of my Macbook Pro beeping 3 times and then I have to forcefully shut it down by pressing the power button. What is this all about? Please help. Thank you.
I saw this report being sent to Apple:
Interval Since Last Panic Report: 581719 sec
Panics Since Last Report: 10
Anonymous UUID: F4CF708D-D85C-4EC5-8047-4FC22C6B03AF
Fri Mar 7 13:00:14 2014
panic(cpu 0 caller 0xffffff80002d1208): Kernel trap at 0xffffff800020c590, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000000000, CR3: 0x0000000007541000, CR4: 0x0000000000040660
RAX: 0xffffff8000000000, RBX: 0xffffff800d35a870, RCX: 0xffffff800cf55cd8, RDX: 0xffffff80008a8fcc
RSP: 0xffffff805e5f3d60, RBP: 0xffffff805e5f3da0, RSI: 0x000000001dcd6500, RDI: 0xffffff800d168778
R8: 0x0000000000000001, R9: 0xffffff805e5f3e88, R10: 0x0000000000000011, R11: 0x0000000000000000
R12: 0x0000000000000000, R13: 0xffffff800d168770, R14: 0xffffff800d168778, R15: 0x0000000000000000
RFL: 0x0000000000010082, RIP: 0xffffff800020c590, CS: 0x0000000000000008, SS: 0x0000000000000010
Error code: 0x0000000000000000
Backtrace (CPU 0), Frame : Return Address
0xffffff805e5f3a00 : 0xffffff8000204d15
0xffffff805e5f3b00 : 0xffffff80002d1208
0xffffff805e5f3c50 :
Model: MacBookPro8,1, BootROM MBP81.0047.B27, 2 processors, Intel Core i5, 2.3 GHz, 4 GB, SMC 1.68f99
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 384 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 5.100.198.104.5)
Bluetooth: Version 2.4.5f3, 2 service, 12 devices, 1 incoming serial ports
Serial ATA Device: Hitachi HTS545032B9A302, 298.09 GB
Serial ATA Device: OPTIARC DVD RW AD-5970H
USB Device: FaceTime HD Camera (Built-in), 0x05ac (Apple Inc.), 0x8509, 0xfa200000 / 3
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfa100000 / 2
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 5
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x821a, 0xfa113000 / 8
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0245, 0xfa120000 / 4
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfd100000 / 2
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd110000 / 3Hmm. The problem still may be the RAM - Apple buys the RAM it puts in its machines from third-party vendors (usually Hynix) so it could be a RAM problem.
There are a couple of things that you can do yourself before taking your machine into an Apple Store or an AASP... download and run an application named Rember that will run a RAM test for you - let it run for a couple of hours or even overnight. If it turns out that your RAM is faulty, Rember will let you know. If it is faulty, then you have a couple of options - replace the RAM yourself or (particularly if you're under warranty still) take the machine to an Apple Store or AASP and have them replace the RAM.
If Rember finds no fault with the RAM, then you'll need to take it into an Apple Store/AASP and get a free diagnosis on the machine. Three beeps do usually indicate faulty RAM, but if it tests good with Rember you likely have another problem - it could be something as simple as the RAM, somehow, not seated correctly or signs of another hardware problem.
Run Rember first... call back with results.
Good luck,
Clinton -
I have a MacBook Pro 13.3 OS- MAC OS X LION.
Whenever I am staring the computer, it says You need to restart your computer by pressing the power button.
I did this number of times and everytime it freezes to the same screen.Solution needed urgently pls.
Thank you for any help in this regard that comes fast.The details of the kernel-panic report is as follows-
Interval Since Last Panic Report: 1458653 sec
Panics Since Last Report: 6
Anonymous UUID: 70BA6A**************************************************
Sun Sep 16 23:00:13 2012
panic(cpu 0 caller 0xffffff80002c4794): Kernel trap at 0xffffff8000290560, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000800028, CR3: 0x000000000a509005, CR4: 0x00000000001606e0
RAX: 0x0000000000000001, RBX: 0x0000000000820000, RCX: 0xffffff801122dc40, RDX: 0x0000000000020501
RSP: 0xffffff80ef3d3da0, RBP: 0xffffff80ef3d3dc0, RSI: 0x000000002b1d78b6, RDI: 0xffffff800342d280
R8: 0xffffff80ef3d3f08, R9: 0xffffff80ef3d3ef8, R10: 0x000000010d901000, R11: 0x0000000000000206
R12: 0xffffff800342d280, R13: 0x0000000000000000, R14: 0xffffff8011cd6500, R15: 0x0000000000800000
RFL: 0x0000000000010206, RIP: 0xffffff8000290560, CS: 0x0000000000000008, SS: 0x0000000000000000
CR2: 0x0000000000800028, Error code: 0x0000000000000000, Faulting CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80ef3d3a50 : 0xffffff8000220792
0xffffff80ef3d3ad0 : 0xffffff80002c4794
0xffffff80ef3d3c80 : 0xffffff80002da55d
0xffffff80ef3d3ca0 : 0xffffff8000290560
0xffffff80ef3d3dc0 : 0xffffff800026c9c3
0xffffff80ef3d3f40 : 0xffffff80002c3fbb
0xffffff80ef3d3fb0 : 0xffffff80002da481
BSD process name corresponding to current thread: fsck_hfs
Mac OS version:
11E2620
Kernel version:
Darwin Kernel Version 11.4.2: Wed May 30 20:13:51 PDT 2012; root:xnu-1699.31.2~1/RELEASE_X86_64
Kernel UUID: 25EC645A-8793-3201-8D0A-23EA280EC755
System model name: MacBookPro9,2 (Mac-6F01561E16C75D06)
System uptime in nanoseconds: 4850001132
last loaded kext at 1796984176: com.apple.driver.BroadcomUSBBluetoothHCIController 4.0.7f2 (addr 0xffffff7f80e16000, size 57344)
loaded kexts:
com.apple.driver.BroadcomUSBBluetoothHCIController 4.0.7f2
com.apple.driver.AppleUSBTCButtons 227.6
com.apple.driver.AppleUSBTCKeyEventDriver 227.6
com.apple.driver.AppleUSBTCKeyboard 227.6
com.apple.driver.AppleIRController 312
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 33
com.apple.iokit.SCSITaskUserClient 3.2.1
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCISerialATAPI 2.0.3
com.apple.iokit.IOAHCIBlockStorage 2.0.4
com.apple.driver.AppleFWOHCI 4.8.9
com.apple.driver.AirPort.Brcm4331 560.7.21
com.apple.driver.AppleSDXC 1.2.2
com.apple.driver.AppleUSBHub 5.0.8
com.apple.iokit.AppleBCM5701Ethernet 3.2.4b8
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleAHCIPort 2.3.0
com.apple.driver.AppleUSBEHCI 5.0.7
com.apple.driver.AppleUSBXHCI 1.0.7
com.apple.driver.AppleACPIButtons 1.5
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.5
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 195.0.0
com.apple.nke.applicationfirewall 3.2.30
com.apple.security.quarantine 1.3
com.apple.security.TMSafetyNet 8
com.apple.driver.AppleIntelCPUPowerManagement 195.0.0
com.apple.driver.AppleUSBBluetoothHCIController 4.0.7f2
com.apple.iokit.IOBluetoothFamily 4.0.7f2
com.apple.driver.AppleFileSystemDriver 13
com.apple.driver.AppleUSBMultitouch 230.5
com.apple.driver.AppleThunderboltDPInAdapter 1.8.4
com.apple.driver.AppleThunderboltDPAdapterFamily 1.8.4
com.apple.driver.AppleThunderboltPCIDownAdapter 1.2.5
com.apple.iokit.IOUSBHIDDriver 5.0.0
com.apple.driver.AppleUSBMergeNub 5.0.7
com.apple.driver.AppleUSBComposite 5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.2.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.driver.AppleThunderboltNHI 1.6.0
com.apple.iokit.IOThunderboltFamily 2.0.3
com.apple.iokit.IOSCSIArchitectureModelFamily 3.2.1
com.apple.iokit.IOFireWireFamily 4.4.5
com.apple.iokit.IO80211Family 420.3
com.apple.iokit.IOEthernetAVBController 1.0.1b1
com.apple.iokit.IONetworkingFamily 2.1
com.apple.iokit.IOUSBUserClient 5.0.0
com.apple.iokit.IOAHCIFamily 2.0.8
com.apple.iokit.IOUSBFamily 5.0.8
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOHIDFamily 1.7.1
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 177.5
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 331.7
com.apple.iokit.IOStorageFamily 1.7.2
com.apple.driver.AppleKeyStore 28.18
com.apple.driver.AppleACPIPlatform 1.5
com.apple.iokit.IOPCIFamily 2.7
com.apple.iokit.IOACPIFamily 1.4 -
My macbook pro doesn't turn on. The battery is charged but the screen stays black when I press the power button. Anybody has a solution for me please?
Try a #1 SMC Reset and see the Apple links, if that doesn't work make a appointment for a evaluation.
..Step by Step to fix your Mac -
My macbook froze and i pressed the power button and the OSX utilities appeared
My macbook froze and i pressed the power button and the OSX utilities appeared .. i don't know if my things got erased or what does it mean and what should i do ? it doesn't let me click out of it or anything. the options are to restore fro time machine, reinstall OSX get help online and disk utility ,, how can i do to not erase anything i do not have an external memory or anything. PLEASE HELP
Hi there. If you have 10.9 Maverick you can get in recovery mode By using /command r Option R or Option. Then you came click on the link to go to disk utilities and repair your disk or do a reinstall of you operating system. I think the screen you are seeing is the recovery screen. Here is a hot of what it looks like. You will have to scroll down a little to see it.http://osxdaily.com/2013/11/05/downgrade-from-os-x-mavericks/ http://support.apple.com/en-us/HT4718 This link tells you what you can do.
-
Hi, when I press the power button on my MacBook nothing happens and it is driving me crazy If anyone knows how I can fix this problem, I will appretiate it very much
Thank youTry an SMC reset, which can often fix that: http://support.apple.com/kb/HT3964 . Note as you scroll down, there are two sets of directions for MacBooks, depending on whether you can remove the battery or not.
-
My new macbook pro doesnt turn on. i press the power button and i can hear it runing but it wont turn on. i tried charging it but nothing works. help me please.
ilmare55555 wrote:
i cant go because if my parents find out my new mac broke they will kill me. i tried to restart it but it wont work i can only hear the fans working and then completely stop after 10 seconds.
It's new and under warranty. That's the reason to go to the Apple Store.
Did something happen to it? -
My new macbook pro doesnt turn on. i press the power button and i van hear it runing but it wont turn on. i tried charging it but nothing works. help me please.
ilmare55555 wrote:
i cant go because if my parents find out my new mac broke they will kill me. i tried to restart it but it wont work i can only hear the fans working and then completely stop after 10 seconds.
It's new and under warranty. That's the reason to go to the Apple Store.
Did something happen to it? -
While I'm using safari, it will freeze up. When I force quit safari and reopen it, I find that I'm back to where I was when I did the force quit and safari remains locked up. When I try to restart the computer, I get a pop up that says that safari cancelled my restart. I then press the power button to shut down the computer. When I reboot the computer and open safari, I see all the tabs and windows that were opened when this issue began, only this time safari isn't frozen. This problem started yesterday.
Has anyone experienced the same problem? Is there a fix for this problem?Try Resetting Safari: Open Safari. Cick on the name Safari in the menu bar. In the drop down menu click Reset Safari.
-
My iphone constantly freezes up. Pressing the power button usually gets me to the last application used but does not allow me to change applications.
Ant ideas?Try resetting it. Hold down the on/off button at the top right and the home botton at the bottom at the same time for abour 5-15 seconds. This will not affect your data. The cycle the iPhone back on. That should clear up the problem
-
I apologize for writing a book, but I think explaining the full story may possibly get me a correct answer. I hope that someone can give me some insight as to what is the problem with my MacBook Pro. I have a MacBook Pro (15-inch Early 2008), model identifier: MacBookPro4,1 running OSX Lion 10.7.5 with 6 GB memory. My wife first noticed a problem with the display. Every so often it would get fuzzy with jumping lines going across the screen making it vitually unviewable. The final time that incident took place the computer froze which required holding down the power button to restart the computer. The computer started up to the point of the Apple logo and the spinning gear for quite some time until the screen darkened from top to bottom displaying the following message in five different languages: "You need to restart your computer. Hold down the Power button until it turns off, then press the Power button again." I have read other blogs and support communities where people get the message intermittently, but my computer would not go past that point no matter what. Through research and the Apple Store I was told that this is a Kernel Panic. The so called "Apple Genius" at the local Apple Store was unable to get the computer to boot past that point even with his gadget. It would not startup in recovery mode, safe mode or off of a disc. I forget exacty what he told me, but he said it was getting past the first two startup steps, but it would not get past the third step which is to mount the desktop. He guessed that it may be a problem with the hard drive; a loose wire or something or other. I disconnected the hard drive completely and took it out. Everything appered to be connected properly. Then I installed it back correctly, but it did not solve the issue. So I guess I disproved his theory of a loose wire... I purchased ProSoft Data Rescue 3 and connected my MacBook Pro to another Apple computer using a firewire 400 cable. I was able to get everything I needed off of the hard drive. I did some more research and I decided to restart the MacBook Pro in verbose mode (holding down the command button and V button). The computer magically started up!!! I was upset that I wasted my money on the ProSoft Data Rescue 3. I managed to take additional items off of the computer and back it up on to an external hard drive. After some time the computer froze. I repeated the power button process to restart and received the same kernel panic. I managed to get the computer to startup approximately six or seven more times via verbose mode; each time the computer staying on for a shorter amount of time before it would freeze. I managed to run Disk Utitlity. I performed first aid to fix the hard drive and it said that the hard drive appeared to be fine. After first aid I erased the hard drive and booted off of a Lion disc to perform a clean install or an erase and install. Lion installed until the progress bar got the the end where I received a message that there was an error installing Lion, please try again. Each time I attempted to install the software I would receive the same message. Eventually the computer would not boot from the Lion disc. I went back to the Apple Store and the Apple Genius was able to get the computer to boot off of his gadget where Lion istalled completely. I set up the computer as a new computer. He said that he partitioned the hard drive as DOS and then back to Mac OS Extended (Journaled) which would get rid of any errors the drive may have had. He guessed that the problem was the hard drive, but was not exactly sure. When I brought it home I installed all of the software applications I had on it previously. Approximately three days later, which may have been the fifth of sixth time starting up the computer, the display became fuzzy again and the computer froze. The computer did restart once and I was able to retreive a "log" which I have pasted below. After if froze for the second time it restarted once using verbose mode and froze almost immediately. After holding down the power key to shut it down and then restart; I received the same kernel panic after the Apple logo and spinning gear which put me right back to square one. Now the computer will not boot via any method. It freezes at the end of verbose mode which forces you to hold down the power button to shut down. I also read that poorly seated ram may cause this issue, but I removed and installed the ram multiple times. I even purchased new ram from Other World Computing (Mac Sales) 6 GB, but that did not make a difference. I think I may see six possible problems on the verbose screen mode, five errors and one warning; I will type them out here:
1. SMC: :smcReadKeyAction ERROR: smcReadData8 failed for key $Num (kSMCKeyNotFound)
2. SMC: :smcReadKeyAction ERROR: $Num kSMCKeyNotFound(0x84) fKeyHashTable=0x0
3. SMC: :smcInitHelper ERROR: MMIO regMap ==NULL - fall back to old SMC mode
4. WARNING - ACPI_SMCCtrlLoop: :initCPUCtrlLoop - no sub-config match for MacBookPro4,1 with 8 p-states, using default stepper instead
5. SMC: :smcReadKeyAction ERROR: smcReadData8 failed for key MOTP (kSMCKeyNotFound)
6. SMC: :smcReadKeyAction ERROR: smcReadData8 failed for key BEMB (kSMCKeyNotFound)
I was hoping that someone could read my log to ascertain wether or not they see a problem that stands out. I was also hoping that someone could tell me if verbose mode provides any information that may be wrong with my computer. I just hope that someone can give me some insight as to what may be wrong with my computer. If it is the hard drive I will easily replace it, but I want to make sure that is the problem first before I waste money on a hard drive or anything else. Please let me know if anyone requires any other information from me.
Thank you!
Interval Since Last Panic Report: 21959 sec
Panics Since Last Report: 1
Anonymous UUID: B62D9AB4-53DD-4F76-90B2-32453302297E
Sat Aug 31 15:20:06 2013
panic(cpu 1 caller 0xffffff80002c4794): Kernel trap at 0xffffff7f81d9d774, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000000010, CR3: 0x0000000011d06000, CR4: 0x0000000000000660
RAX: 0x0000000000000004, RBX: 0xffffff809eb71000, RCX: 0xffffff8000892604, RDX: 0xffffff80b69d3aa8
RSP: 0xffffff80b69d3bd0, RBP: 0xffffff80b69d3bd0, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000010751b4, R10: 0xfffffffffffffff4, R11: 0xffffff8000640fd4
R12: 0xffffff809eb71000, R13: 0x0000000000000000, R14: 0x0000000000000000, R15: 0x0000000000000010
RFL: 0x0000000000010202, RIP: 0xffffff7f81d9d774, CS: 0x0000000000000008, SS: 0x0000000000000010
CR2: 0x0000000000000010, Error code: 0x0000000000000000, Faulting CPU: 0x1
Backtrace (CPU 1), Frame : Return Address
0xffffff80b69d3880 : 0xffffff8000220792
0xffffff80b69d3900 : 0xffffff80002c4794
0xffffff80b69d3ab0 : 0xffffff80002da55d
0xffffff80b69d3ad0 : 0xffffff7f81d9d774
0xffffff80b69d3bd0 : 0xffffff7f81d8913a
0xffffff80b69d3c20 : 0xffffff7f81d89928
0xffffff80b69d3c40 : 0xffffff7f81d5be8f
0xffffff80b69d3c70 : 0xffffff7f8087f832
0xffffff80b69d3cb0 : 0xffffff7f8087f93d
0xffffff80b69d3cd0 : 0xffffff7f8088b625
0xffffff80b69d3d40 : 0xffffff7f80889c76
0xffffff80b69d3d80 : 0xffffff80006245ca
0xffffff80b69d3dd0 : 0xffffff8000657d4e
0xffffff80b69d3e30 : 0xffffff80002a3851
0xffffff80b69d3e80 : 0xffffff8000223096
0xffffff80b69d3eb0 : 0xffffff80002148a9
0xffffff80b69d3f10 : 0xffffff800021bbd8
0xffffff80b69d3f70 : 0xffffff80002aef10
0xffffff80b69d3fb0 : 0xffffff80002daec3
Kernel Extensions in backtrace:
com.apple.iokit.IOGraphicsFamily(2.3.4)[D0A1F6BD-E66E-3DD8-9913-A3AB8746F422]@0 xffffff7f80874000->0xffffff7f808acfff
dependency: com.apple.iokit.IOPCIFamily(2.7)[5C23D598-58B2-3204-BC03-BC3C0F00BD32]@0xffffff 7f80849000
com.apple.GeForce(7.3.2)[7E1D7726-416F-3716-ACCB-E1E276E35002]@0xffffff7f81d590 00->0xffffff7f81e1bfff
dependency: com.apple.NVDAResman(7.3.2)[97284661-2629-379E-B86B-D388618E8C30]@0xffffff7f808 bf000
dependency: com.apple.iokit.IONDRVSupport(2.3.4)[7C8672C4-8B0D-3CCF-A79A-23C62E90F895]@0xff ffff7f808ad000
dependency: com.apple.iokit.IOPCIFamily(2.7)[5C23D598-58B2-3204-BC03-BC3C0F00BD32]@0xffffff 7f80849000
dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[D0A1F6BD-E66E-3DD8-9913-A3AB8746F422]@0 xffffff7f80874000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
11G63
Kernel version:
Darwin Kernel Version 11.4.2: Thu Aug 23 16:25:48 PDT 2012; root:xnu-1699.32.7~1/RELEASE_X86_64
Kernel UUID: FF3BB088-60A4-349C-92EA-CA649C698CE5
System model name: MacBookPro4,1 (Mac-F42C89C8)
System uptime in nanoseconds: 62230646656
last loaded kext at 53384504695: com.apple.filesystems.autofs 3.0 (addr 0xffffff7f81efc000, size 45056)
loaded kexts:
com.apple.filesystems.autofs 3.0
com.apple.driver.AudioAUUC 1.59
com.apple.driver.AppleTyMCEDriver 1.0.2d2
com.apple.driver.AppleUpstreamUserClient 3.5.9
com.apple.driver.AppleHDAHardwareConfigDriver 2.2.5a5
com.apple.driver.AppleHDA 2.2.5a5
com.apple.GeForce 7.3.2
com.apple.driver.SMCMotionSensor 3.0.2d6
com.apple.driver.AppleSMCPDRC 5.0.0d8
com.apple.driver.AppleSMCLMU 2.0.1d2
com.apple.driver.AppleMuxControl 3.1.33
com.apple.driver.AppleBacklight 170.2.2
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.iokit.IOBluetoothSerialManager 4.0.8f17
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AudioIPCDriver 1.2.3
com.apple.driver.ApplePolicyControl 3.1.33
com.apple.driver.ACPI_SMC_PlatformPlugin 5.0.0d8
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.AppleUSBTCButtons 227.6
com.apple.driver.BroadcomUSBBluetoothHCIController 4.0.8f17
com.apple.driver.AppleUSBTCKeyEventDriver 227.6
com.apple.driver.AppleUSBTCKeyboard 227.6
com.apple.driver.AppleIRController 312
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 33
com.apple.iokit.SCSITaskUserClient 3.2.1
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.1.0
com.apple.iokit.AppleYukon2 3.2.2b1
com.apple.driver.AppleUSBHub 5.1.0
com.apple.driver.AppleAHCIPort 2.3.1
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AirPortBrcm43224 501.36.15
com.apple.driver.AppleFWOHCI 4.9.0
com.apple.driver.AppleIntelPIIXATA 2.5.1
com.apple.driver.AppleUSBEHCI 5.1.0
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleUSBUHCI 5.1.0
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleACPIButtons 1.5
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.5
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 195.0.0
com.apple.nke.applicationfirewall 3.2.30
com.apple.security.quarantine 1.4
com.apple.security.TMSafetyNet 8
com.apple.driver.AppleIntelCPUPowerManagement 195.0.0
com.apple.kext.triggers 1.0
com.apple.driver.DspFuncLib 2.2.5a5
com.apple.nvidia.nv50hal 7.3.2
com.apple.nvidia.nvGK100hal 7.3.2
com.apple.nvidia.nvGF100hal 7.3.2
com.apple.NVDAResman 7.3.2
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.driver.AppleHDAController 2.2.5a5
com.apple.iokit.IOHDAFamily 2.2.5a5
com.apple.iokit.IOSurface 80.0.2
com.apple.iokit.IOSerialFamily 10.0.5
com.apple.iokit.IOAudioFamily 1.8.6fc18
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleGraphicsControl 3.1.33
com.apple.iokit.IONDRVSupport 2.3.4
com.apple.iokit.IOGraphicsFamily 2.3.4
com.apple.driver.AppleSMC 3.1.3d10
com.apple.driver.IOPlatformPluginLegacy 5.0.0d8
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.IOPlatformPluginFamily 5.1.1d6
com.apple.driver.AppleFileSystemDriver 13
com.apple.driver.AppleUSBBluetoothHCIController 4.0.8f17
com.apple.iokit.IOBluetoothFamily 4.0.8f17
com.apple.driver.AppleUSBMultitouch 230.5
com.apple.iokit.IOUSBHIDDriver 5.0.0
com.apple.driver.AppleUSBMergeNub 5.1.0
com.apple.driver.AppleUSBComposite 5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.2.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOATAPIProtocolTransport 3.0.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.2.1
com.apple.iokit.IOUSBUserClient 5.0.0
com.apple.iokit.IOAHCIFamily 2.0.8
com.apple.iokit.IO80211Family 420.3
com.apple.iokit.IONetworkingFamily 2.1
com.apple.iokit.IOFireWireFamily 4.4.8
com.apple.iokit.IOATAFamily 2.5.1
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOUSBFamily 5.1.0
com.apple.iokit.IOHIDFamily 1.7.1
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 177.11
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 331.7
com.apple.iokit.IOStorageFamily 1.7.2
com.apple.driver.AppleKeyStore 28.18
com.apple.driver.AppleACPIPlatform 1.5
com.apple.iokit.IOPCIFamily 2.7
com.apple.iokit.IOACPIFamily 1.4
Model: MacBookPro4,1, BootROM MBP41.00C1.B00, 2 processors, Intel Core 2 Duo, 2.4 GHz, 6 GB, SMC 1.27f3
Graphics: NVIDIA GeForce 8600M GT, GeForce 8600M GT, PCIe, 256 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR2 SDRAM, 667 MHz, 0x7F7F7F7F7F9B0000, 0x4354353132363441433636372E4D31364643
Memory Module: BANK 1/DIMM1, 2 GB, DDR2 SDRAM, 667 MHz, 0x7F7FBAFFFFFFFFFF, 0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.15)
Bluetooth: Version 4.0.8f17, 2 service, 18 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: Hitachi HTS543225L9SA02, 250.06 GB
Parallel ATA Device: MATSHITADVD-R UJ-867
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0230, 0x5d200000 / 3
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2I had already written a book and I did not want to bombard people with more information, but in my previous research I did come across the major issues with the NVIDIA card. I also was well aware that Apple offered a replacement program that ended in December of 2012. I was going to add that in my original post, but I discounted that theory because I put my faith in the so called "Apple Genius" when I made my second trip to the Apple Store. I brought the NVIDIA card issue to his attention and asked him if he thought that may be the problem, but he said no. He said if it was the NVIDIA card that the screen would be completely black and there would be no startup chime. When I experienced the screen issues I thought it was a problem with the NVIDIA card or the logic board. I asked myself, how can a flawed hard drive cause the screen to act funny.
nbar and Rick Warren, I thank you both for your help and insight; people like you are the real "Apple Geniuses." I was hoping there was a way I could wipe the hard drive before I dumped the computer or attempted to sell it. I guess I will look into purchasing a new machine when I have the funds. Again...thank you both!
Maybe you are looking for
-
Estrutura de envio do ECC para XML 2.0
Bom dia, pessoal estava olhando function J_1B_NF_MAP_TO_XML que faz o mapeamento do ECC para XML e percebi que o mesmo não tem nenhum comentário sobre a NF-e 2.00 somente 1.10 como no código abaixo, será que ficou faltando alguma OSS, ja fiz a confe
-
Watched Folders not processing - ALC-DSC-003-000
This error seems familiar, but I've yet to see a solution for it in the forums. My watched folders have stopped processing files and this is the first few lines I get from WebSphere's systemErr.log. See first and last lines: [19/04/10 19:17:33:229 B
-
Icon Preview Problem in Finder
Hi, I've had my new MacBook for about a month now, and as my photo collection has grown I'm starting to notice that while using CoverFlow (which I have as the default view for most of my folders), there are always some icons that appear as a generic
-
Business rules engine faults..
Can someone please advise on what could cause this issue? We are using SOA suite 11.1.1.2 1. The rules engine takes an input as usual but doesn't send any output. 2. The BPEL process that invokes the rules sends out a bpelFault instead - (because the
-
File.copyTo (and copyToAsync) extremely slow on Android. e.g. 1/2 second per tiny XML file. Help?
On first launch, my app copies about 100 tiny XML files from application dir to storage dir. It takes about 35 seconds. That is clearly an issue. It takes about 1/100th of a second on any other platform. I've switched to copyToAsync() so that the use