My MacBook air will not boot up completely
My Machook air has crashed. While using iPhoto to review photos taken with a 12 mp camera, the computer warned me in several languages to restart. This has occurred on several occasions using iPhoto. Upon shutting the computer down and after restarting the computer, it failed to boot up completely, shutting off halfway through the process. I tried resetting the pram however the computer only provided me with a choice of repairing the hard drive or reformatting the computer.
After several attempts to repair the HD/Disk. It gave a message to save what files I could and reformat the drive and reinstall the softwear. However the computer will not let me do so and gives me a message that the HD is locked. Futher attempts to restart or reset ends in failure. The computer will not boot up completely before it crashes/shutsdown.
Thanks in advance for any help.
Make a "Genius" appointment at an Apple Store to have the machine tested.
Similar Messages
-
My Macbook Air will not boot. It starts and hangs up at the apple logo. Is there a bypass to see what the problem is?
Try a Safe Boot by holding down the Shift key between the startup tone and the Apple Logo. This will take longer than a normal boot and display a progress indicator. If successful, Go to System Preferences > Startup disks > select your Boot drive and restart.
Regards,
Captfred -
My MacBook Air will not boot up all the way.
My MacBook Air will not boot up all the way, it only allows me to sign in and then it stays on a white screen. I tried restarting, rebooting, recovery and smc reset. Nothing works, it stays with the same problem. How can I fix this?
Try a safe boot:
http://support.apple.com/kb/HT1564?viewlocale=en_US
Ciao. -
MacBook Air will not boot. Error Message says "Your Computer restarted because of a problem."
MacBook Air will not boot. Error Message says "Your Computer restarted because of a problem."
If you can't start up and log in in the usual way, try in safe mode.
During startup, you’ll see a progress bar, and then the login screen, which appears even if you normally log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Log in as an administrator to carry out these instructions. If you have only one account, you are the administrator.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
Safe mode is slower than normal, and some things won’t work at all.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t start in safe mode.
If you're able to log in, launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report. -
Macbook air will not boot 10.5.7 after screen replacement
Hello
Following screen replacement on original macbook air I can only take system to 10.5.6. Will not update to 10.5.7 or 10.6.
Any suggestions?
GeorgeVBTW, I see the threads on the Thunderbolt update kernel panics. I was kind of hoping Apple resolved the problem since I thought they had pulled the update. Anyway, I do not *think* I am getting a Kernel panic as the boot does not even get as far as the Apple logo. It just sits on the gray screen and does nothing.
-
MacBook Air will not boot to previous image
I got a new MacBook Air for my company and used a prior image that has been used on previous model MacBook Pro's (Retina 15", 13", Air 2012, etc). When I apply the image, it does not boot. Is there any way I can get the dmg to boot on the new laptop without me having to rebuild it from scratch?
Please advise.Welcome to Apple Support Communities
What Mac OS X version has the image got? Note that the new MacBook Air isn't compatible with OS X 10.8.4 or older. If the image doesn't contain this version, you won't be able to use that image. Also, note that the MacBook Air may use a special version that isn't compatible with the OS X 10.8.4 version available for other Macs, so you won't be able to boot from the image -
MacBook Air will not boot "Error -6003F"?
Booting Macbook Air would show white screen with folder containing flashing ?. Tried booting with OSX Snow Lepard. Now comes on with white screen and Apple Logo. Using an external USB 2 DVD powered by computer. No external power source. Holding the option key during boot I'm asked for my network choice and password then it shows Internet Restore on globe that switches to ! error code _6003F.
Won't boot! Any help out there, ThanksBooting Macbook Air would show white screen with folder containing flashing ?. Tried booting with OSX Snow Lepard. Now comes on with white screen and Apple Logo. Using an external USB 2 DVD powered by computer. No external power source. Holding the option key during boot I'm asked for my network choice and password then it shows Internet Restore on globe that switches to ! error code _6003F.
Won't boot! Any help out there, Thanks -
How do I uninstall Yosemite please ? Since I upgraded my 2011 MacBook Pro will not boot up
My 2011 MacBook Pro will not boot up following my upgrade to Yosemite. How do I uninstall or downgrade back to the previous version of OS please ?
You can't downgrade or uninstall unless you first erase the drive. Try the following:
Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
Choose the version you have installed now:
OS X Yosemite- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless. -
HT4718 I recently upgrade my OS and now my MacBook Pro will not boot up
I recently upgrade my OS and now my MacBook Pro will not boot up
Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless. -
Macbook pro will not boot. I get the gray screen, an apple icon and spinning wheel. I tried to start in safe mode, but get this same screen. The only thing different is that I added the zedge update app to do a sync for adding ringtones to my apple cell phone. How can I get a good boot. I am fairly new to apple computer.
Reset PRAM: http://support.apple.com/kb/PH4405 and then try a normal boot.
Run the Startup Manager to select Startup disk: http://support.apple.com/kb/HT1310
If those did not work your disk may be sick or dying. The top priority at this point is to make a backup copy of your data.
Check the health of the disk. Boot in Recovery Mode (Boot, Command-R). Run Disk Utility. Click on the upper left disk icon. Does the S.M.A.R.T. status say “Verified”? If not the disk/SSD is unhealthy and needs to be replaced. Even if it does not show “Verified” you can still attempt a backup.
Click on the icon indented below, usually called “Macintosh HD” and Verify Disk. If it finishes with a green “OK” message then all is well with the disk. If it shows errors in red then you have found a problem to address once the system is backed up. Do not attempt software repairs until you have secured the data.
If the disk will not show up at all in Disk Utility as your ran the tests above then it may be dead or it may have a bad internal SATA cable. A trip to an Apple store for confirmation would be in order.
If you have an external disk drive you can use as a backup drive then do so. If not Google “Hitachi USB 3.0 external hard drive 1TB” to purchase one or go to a brick-and-mortar store (including an Apple store) to pickup one. Any 1 TB external drive will do.
Assuming it is still breathing you can try to recover the data without booting from the sick disk.
Reformat the external disk. (This will erase all data on the external disk.)
Boot in Recovery Mode. Start Disk Utility. Plug in the new disk. Select it’s disk Icon (the second one down, left justified). Select the Partition tab.
Partition Layout > Single Partition
Name: Emergency Recovery 1 (or whatever name you wish to use)
Format: Mac OS Extended (journaled)
Options… > GUID Partition Table > OK
Apply
Select the Restore tab.
Drag the old system volume (Macintosh HD) to Source.
Drag the new disk volume (Emergency Recovery 1) to Destination.
Click on Restore.
It may take a long time for the backup.
If that will not complete post back for other emergency data recovery methods, including those from a brody.
If the backup succeeds, use the First Aid tab in Disk Utility to select the old volume (Macintosh HD) and Repair Disk. If it does not finish with a green OK message try to repair it once or twice more. If it repairs with a green OK message, will it boot normally? If not, boot from the Recovery Partition and reinstall OS X.
If it is still not healthy, post back for further instructions. -
Macbook air will not connect to the wifi network
I recently had to replace my wireless network router and now my macbook air will not connect to the network. it worked fine with the old wireless router. Now, i get a "unable to join wi-fi network" message. The network ID (SSID) and password (WPA) are the same as before. I try to manually enter the password, but continue to get the previous message.
Any help in figuring out how to correct this problem is greatly appreciated.
Also, I have several PCs in the house that have had zero problems connecting to my wireless with the new router. What am I doing wrong?Hi,
Ever since did the last airport utility update this has been happening.
I believe the airport utility update is solely a software update. Repair permission and repair disk (boot from your installation disk A) may help.
Other wise, http://osxdaily.com/2009/12/22/mac-wireless-problems-guide-to-troubleshooting-ai rport-wireless-problems-on-your-mac/ may help, too.
Cheers. -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My Mid 2010 MacBook Pro will not boot
My Mid 2010 MacBook Pro will not boot regularly, in safe mode, in recovery mode or from original OS DVD. Is this the logic board?
I've tried resetting the SMC and pram numerous times and even tried switching out hdd's to try and do a clean install on a new hdd.
If I attempt to boot regularly or from recovery drive the grey apple logo appears for a period before the screen goes black and the power LED operates as though in 'sleep' mode. I'm unable to wake it from this state and the same applies to booting in safe mode.
When attempting to boot from the OS DVD that was originally packed with the computer it just freezes on the language select option, this occurs with the other hdd's I have attempted to use.
Any other suggestions to get it working? I fear the logic board has gone and that the repair won't be worth the money.
Thank you in advance.Hi JRC8.8,
It sounds like you have been on the right track in trying to troubleshoot this issue. You may want to see if your MacBook Pro will boot directly to the Apple Hardware Test, as outlined in the following article:
Apple Support: Using Apple Hardware Test
http://support.apple.com/kb/ht1509
Regards,
- Brenden -
My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums for hours, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how I can fix this. Many thanks!
The warranty entitles you to complimentary phone support for the first 90 days of ownership.
If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies. -
My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.
If you have been using the mac.com Apple ID to make iTunes purchases recently, then there should be no issues continuing to use it with the new iPhone. I would abandon the new ID as you will never get Apple to merge the two IDs. I have had a mac.com ID for years and continue to use it with my iPhone 4S.
Tell us the issues that you encounter trying to set up the iPhone with the mac.com account.
Maybe you are looking for
-
HWF UI work list not loading in BPM worklist page (on clustered env)
hello - Please reply directly as I am not on this alias. My SOA project (BPEL+HWF) is successfully deployed on the clustered env successfully. My BPEL process runs fine. But my HWF_UI taskflow fails to load on the browser (IE and Firefox, same error)
-
Problems with two new LCD monitors and my G5 Power Mac
I bought two of these Westinghouse Digital LCD monitors: http://www.macaddict.com/issues/2005/11/reviews/lcm When I plugged in the first one, my Mac's power-on light was on, but the Power Mac G5 (1.6 ghz, 1.25 gb RAM) wouldn't boot and the light woul
-
Livecycle ES 8.2 Compatability
Does Livecycle ES 8.2 works on Windows vista 64-bit Home premium? or Does it work on Windows XP SP2?
-
How can I shorten the length of my ringback tone?
How can I shorten the length of my ringback tone?
-
Can't add jpg files to Premier Elements 9 timeline
When I try to add jpg files to Premiere Elements 9 timeline, I get an error saying "This file is not supported, or the required codec is not installed". Windows 7 can open/display every one of the jpg files. Photoshop Elements can open them as well.