My MacBook pro don't start up.

How to reset this MacBook to get some reaction?

Hi f,
Does it make the startup sound?
Are you able to boot to the install disc?

Similar Messages

My MacBook pro don't start after installing Lion

Hi
I just downloaded Lion from AppStore, then my MacBook pro wan,t start. It is only the apple.
Br/Anders

I'm afraid that with hardware problems, such as you dsecribe, are difficult (if not impossible) to diagnose over the Internet. You're just going to have to break down and make the trip to your nearest Apple Store or AASP and have them diagnose your computer. I take it that you didn't purchase the extended AppleCare Protection Plan? Let's just hope it's not a logic board problem...
Clinton

My isight camera was not working. so i tried to smc reset it as said in apples support community but now wat happened is my macbook pro don't charge, it don't show any light for checking charge, nor it starts up. please help. Thanks

my isight camera was not working. so i tried to smc reset it as said in apples support community but now wat happened is my macbook pro don't charge, it don't show any light for checking charge, nor it starts up. please help. Thanks

Try zapping the PRAM. See KB Article http://support.apple.com/kb/PH11243 OS X Mountain Lion: Reset your computer’s PRAM
If you are still under warranty and/or have AppleCare, call them. Let them deal w/it.

`my macBook Pro won't start up. Just get that gray blueshy kind of screen and don't go nowhere.

My MacBook Pro won't start up. Just get that gray, blueishy screen and don't go on.

Try a safe boot.
http://support.apple.com/kb/TS2570
This boot takes longer than a normal boot, be patient. If it boots login, and see if it seems normal. If so, logout and reboot normal.

TS3423 17" macbook pro won't start blue file with question mark is all that appears on the screen

My old macbook pro will not start up. Worked fine yesterday, today all I gat is the startup sound and a blank blue screen. After a while the screen shows a file folder icon with a question mark in it. Any ideas

Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by:
Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
Boot drive's directory has been corrupted - Repair with Disk Utility.
Critical system files are damaged or deleted - Reinstall OS X.
The disk drive is physically non-functional - Replace the hard drive.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD:
Boot From The Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Hi! My MacBook Pro won't start! HELP !!!

Hi! My MacBook Pro won't start! I have tried everything I can think of like Safe Mode (doesn't work), Recovery (does not find Recovery Drive), Booting with OS Snow Leopard Cd (doesn't work)...
I have really no clue about what to do now... I paid quite a lot of money for this computer and am pretty short of money nowadays! Would like to repair with help rather than having to take it to Apple Store.
Has anyone had this same problem?
All I get is white screen + grey Apple and spinning grey disk... it's 100% frustrating! Any help would be more than welcome since I think i've tried EVERY SUGGESTION on this Support Center and Youtube videos...
This MBP is from 2011, runs on OS X 10.6.8
I tried booting with OS X Snow Leopard CD, it didn't work! (my cd player works! recognizes the Snow Leopard CD, but then never opens it... goes back forever to the with screen + apple and spinning disk)
I don't care about the content, it's OK if i lose all DATA... I just want to bring this Mac BACK TO LIFE!
When i run coomand on root# fsck -fy --> RESULT = my HD was checked and seems to be FINE!
Thanks

Please make a Genius Appointment and take it in for service.

Macbook pro isn't starting

my macbook pro isn't starting. it gets as far as the apple logo and loading wheel but does go any further, please help!!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Macbook Pro won't start properly... keeps restarting without chime!

Macbook Pro won't start properly... keeps restarting without chime!
Late 2007 Macbook pro. OS upgrade worked great for me.
I have had this problem on and off for a month or so. I simply cannot figure out what the issue is. I have tried poerup with and without AC power and with/without battery installed.
Starting in Safe mode does not help.
Trying to start with a disk does not help.
It sort of seems like it might be an internal power issue or GPU issue.
It also feels sort of like a software compatibility issue since my Macbook Pro gets reallly slugish for no apparent reason sometimes and IU have to restart.
I have three different anti-virus programs so I doubt it is a virus issue.
I noticed all this start after I did a Mountain Lion upgrade and then tried to start up VMware Fusion. Fusion seemed to just bog down the computer horribly but did not cause a system crash.
I need to edit an important sequence on Final Cut Pro and don't want it to freeze me out!
Anyone who has had this problem and resolved it please let me know
God bless

Systematically run through this list of fixes.
..Step by Step to fix your Mac
If it doesnt chine it doesn't mean much, the mute could be on or you installed a anti-chime software.

My Macbook Pro won't start

This problem isn't like the others, it's completely different. So, I start my day like normal, I turn my Macbook Pro on, it starts loading at the startup screen. But this time, the loading bar suddenly dissapeared, so just the apple symbol and the wheel. Right afterwards, it shuts off. Not sleep mode, like completely shut down. I have already tried putting it in "Safe Mode", but that didn't help. And then when it's shut down, the charger light isn't on when it's plugged in. What do I do to solve this situation?

You don't need the menu bar to do an SMC reset. You don't do anything as the computer starts up, you just need to shut down the computer, which you can do by holding down the power button
Did you read the part for your computer? maybe you should read the article yourself...
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.

My MacBook Pro, does not start after pushing start button. The side bar starts and stops at half way.

My MacBook Pro, does not start after pushing start button. The side bar starts and stops at half way.

Hy myneck,
Happy Holidays! The resource below may provide some steps to try if your MacBook Pro won't start.
Troubleshooting: My computer won't turn on - Apple Support
http://support.apple.com/en-us/TS1367
This article discusses what to do if your Mac won't turn on. To differentiate this from a display issue, be sure that when you press the power button:
You don't hear a startup chime.
You don't hear any fan or drive noise.
There is no video on your built-in or external display
If your computer has power but doesn't display any video, it may have one or more of these similar symptoms when you press the power button:
You may hear a startup chime.
You may hear fan or drive noise.
You may see a light from the Sleep LED (if your Mac has one).
Pressing the Caps Lock key on the keyboard causes it to light.
If any of these display-related conditions occur, see Troubleshooting: My computer has no video instead. Otherwise, continue with this article.
If your computer won't turn on, try each of these steps:
Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
MacBook Pro: How to remove or install memory
MacBook: How to remove or install memory
Mac Pro: How to remove or install memory
Mac mini: How to remove or install memory
iMac (27-inch, Late 2012): Installing or replacing memory
iMac: How to remove or install memory
Reset the SMC.
If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
I hope this information helps ....
- Judy

MacBook pro, will not start up- drive begins

MacBook pro, will not start up- drive begins?

OK, then try this:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Since you can boot into safe mode successfully, I'm assuming the problem may be with a bad third-party extension or plug-in (such as a driver for third-party hardware or a bad Flash plug-in, for example.) It can also be a problem with a bad cache or preference file. If the above doesn't help then use a utility like Lion Cache Cleaner 6.0.5, Cocktail, TinkerTool Sys..., or OnyX to clean out user, system, and font caches.

Early 2008 MacBook Pro - Very slow start up, very hot

Hi All,
Looking for some help. Searched quite a few of the online forums and have not been able to resolve this issue.
A few months back, my old reliable MacBook Pro (early 2008) started behaving oddly. Have no idea why, but went to start it up one day, and it took forever to start up and get me to the login screen. Been like that ever since. Occassionally, when I finally get to the login screen, the keyboard will not function. After a few minutes though, it always works. This only happens about 5% of the time. Once I log in, everything about the computer from a performance perspective seems to be pretty normal In addition to the slow start up, however, system gets extremely hot at the top of the keyboard, near the monitor. Fans run fast almost all the time when the system is powered on, and often when it is 'asleep'. CPU Temp goes to about 170, and the fans are always between 2400 and 3500.
I took it to Apple a while back, and based on the incredibly slow start up time they believed it was a disk issue. I went ahead and purchased a 500GB internal drive and this past weekend used SuperDuper to copy the original boot disk. All went well and I now have a new internal disk. At the same time, I upgrade the RAM from 2GB to 4GB.
After all that, the system is still very slow at startup and runs as hot as it did before. I will say, it does seem to be slightly faster on the startup, but not what I had become accustomed to for the first 4 years of use.
I looked at the activity monitor and don't see any processes hogging resources.
No anti-virus software running.
Currently running Mac OSX 10.6.8
My battery is pretty muc shot, but I never really use the system unplugged.
Any thoughts? Thanks in advance!

Hi there
I am having a similar issue, my mac is the same age but I am getting a major heat issue.
looking for some possible solutions.

My 2009 2.26Ghz MacBook Pro won't start up

My 2009 2.26Ghz MacBook Pro won't start up. I know it's not the HDD because I replaced it with the old one I had in it and it did the same thing. I also know it isn't the HDD because I can boot of of it when I attatch it via an external HDD enclosure. It sometimes turns on if I let it sit for 30 minutes and if it does turn on it works perfectly and has no symptoms until I close it then it freezes up when I wake it up and I have to hard restart it but it doesn't restart then. It seems to do this more so if I close it then move it (put it in my bag and go to school). It's getting me really upset cause if it's my motherboard it's $600 to replace (almost not worth replacing except I don't have $1400 for a new MBP) please give any advice. I thought about buying the data doubler by OWC but that would be a last resort. I upgraded the ram to 8gb, 1333mhz (I know it uses 1066Mhz but I couldn't find any where I live so I put in 1333mhz ram expecting it to underclock to 1066 which it seems to have done that with no issue to my knowledge just thought I'd add that in case though.

Sluggish could be due to not enough ram for what you want to do.
Keep working with it, you may need to put more ram in, but go for the stuff that meets the specs.
A much liked source on here is OWC, http:www.macsales.com you only have to look up your machine to get exactly the right stuff.
Get back with how it is working, would like to hear more.

17" Macbook Pro won't start at all. I shut it down last night at 80% and now there is only black screen, no light, no sound. What to do?

My 17" Macbook Pro won't start at all. I shut it down last night at 80% and today I get only a black screen with no sound, no light, nothing. The power cord light does show orange when plugged in. I don't know exactly which OS it is. It's model # A1286. I've tried all the tips about holding down different keys to no avail. Anyother ideas? (The serial # is w8******agu if that helps.) Many thanks.
<Edited By Host>

I had the exact same issue... Macbook Pro late 2008 with Core2Duo. Went to all the steps suggested in the knowledge base, tried to reset the SMC, but to no avail. Took it to the Macstore in Mexico, the wanted to replace logic board for $800.... Finally, I sent it to a logic board repair service, where they "fixed" the logic board for $200. It worked perfectly for 4 months, then happened again
Any ideas?? I would appreciate any help!!!!!

Attn: macbook pro won't start up past grey screen NO MATTER WHAT

my macbook pro won't start up past the grey screen, NO MATTER WHAT I DO. i've searched all the discussions on this, and NOTHING WORKS. nothing caused this either - i was just browing the internet and using ichat, and my computer shut down, and that is when this started.
I am EXTREMELY disappointed with this bullstein. My computer works great, etc., and I support mac and apple to the nth degree, but then some stupid crap like this happens and I can't use my computer at all. I have to use my sister's **** ibook g3 to even do this.
PLEASE HELP. do NOT post what you have already posted in the other discussions, and i've already been welcomed to the boards. I can't go to an apple store because i'm on vacation in new mexico for the summer, and there no stores anywhere near here. is there any real advice around here? I need to use my computer. That is why I spent close to $4,000 for it with upgrades and software.

where can i get an install disc for the macbook pro?
You really need to use the one that came with your MBP. If you don't have it, a retail Tiger OS X disc should work.
also, could an archive/install potentially free up some harddrive space on my computer?
No, it will actually use more space, so you will need at least 6G of free space. To clean your hard drive, use WhatSize.
WhatSize >>
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
 An Apple User Group 

My MacBook pro don't start up.

Similar Messages

Maybe you are looking for