My MacBook pro motherboard needs replacing (expensive!!), would I be able to remove the hard drive and have it put into my partners MacBook air?

My MacBook pro would not boot up, took to genius bar and tech tried everything to boot up, but no luck, he says it looks like main board has gone, It would cost £750!! He said if I wanted to purchase a new mac, they could transfer my hard drive to the new mac. My partner has a MacBook air, which they hardly use, so I was wondering if the techs would be able to transfer my hard drive from the pro to the MacBook air? Any advise would be appreciated

Not the Hard Drive itself! In the MacBook (Pro) you have 2.5" hard drives, and in the MacBook Air there are 1.8" (the older once) or special form factors SSDs (MacBook Air 2011). So the hard drive quite bigger in your MBP.
But the data could be transferred to the MacBook Air with an external enclosure, if the hard drive in the MacBook Air is big enough.

Similar Messages

I havea 2007Mac Book Pro and a Genius told me that it is "vintage" and that the "logic board" is bad. He removed the hard drive and told me to buy a "sled" to retreive the data. Is it worth trying to fix it so that I don't have to buy a new one?

I have a 2007 Mac Book Pro and a Genius told me that it is "vintage" and that the "logic board" is bad and no longer supported. He removed the hard drive and told me to buy a "sled" to retreive the data. Is it worth trying to fix it so that I don't have to buy a new one? Where should I take it? Thanks.

djgornik,
if the Genius is correct and the logic board is bad, then replacing the logic board would be fairly expensive. What problems are you seeing with your MacBook Pro that caused you to visit the Genius in the first place? Whether it’s worth trying to fix it or not depends on your particular circumstances, such as your willingness to trade time for money in pursuing repair vs. replacement.

I have a 1st Gen Time Capsule 1tb. It turns on, boots up and turns green for 5-10 mins, but then turns solid orange and then blinks orange. I have removed the hard drive and replaced the power supply . . . still the same problem. Suggestions?

I purchased a used 1st Gen Time Capsule with a 1 tb hard drive.
When I plugged it in and did the initial setup, it worked fine, but gave me a hard drive error. A few minutes later the green light turned solid orange, then blinking orange, then the status light went off. The lights in back stayed on.
I removed the hard drive and rebooted, it turned green for 5-10 minutes then reverted back to a solid orange, blinking orange, then went off.
Next I purchased a remanufactured internal power supply, and installed it (without the hard drive in). It turned green almost immediately. After about 15-20 minutes, I decided to try to install the hard drive again, booted it up, and tried to erase the hard drive with was working properly according to the software. It stopped erasing the disc after about 20 minutes and turned solid orange again, then blinking, then no status light (but back lights were still lit).
I'm a bit flabbergasted at this point, any suggestions on what to do next? I think i've pretty much replaced everything except the logic board, but can't seem to find any information on the symptoms of a logic board malfunction.
Thanks!!!!!!!

A Gen3 is identical board to a Gen4 although they have some differences in firmware and wireless card was updated on every model.. but a Gen3 is substantially faster than Gen1, Gen2 which also have identical boards.
You can with careful shopping get a Gen3 pretty cheap.
Most use a delta power supply which I think is a lot better than the flextronics used in most Gen1/2
You can sell back the parts to ebay.. people still would buy the power supply etc. Even just the case can be useful to a repairer.
But if the board is gone.. it is hard to repair.. not impossible.. but hard.
Gen 3 and Gen 4 are not without faults.
See this page.
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair/new-issue-with-a1355-gen-3-tc
I have fixed it a different way.. by using the small converters you can buy in bulk from ebay for $1 each.. KIS3R33 .. they produce 3.3V at 2A peaking at 3A.. amazing.. I keep using them to replace onboard power converters by removing the inductor and simply power directly.. the end result has worked great. You can simply change the resistors around and get any output from 1v to 20v depending on input.
Is it worth doing it .. no of course not.. it will waste many more hours than $50 is worth.. but it is kind of fun that you can actually make things work again.
Here is a pic of the Gen 3 totally powered by me. All onboard power removed.
This was to track down the fault in the Gen3.. but I am kind of pleased that it ended up neat enough and reliable enough to work for more than a year.. the Gen3 still serves as a way to get Netflix via network for a friend running 24/7.
The units supply (from left to right)
1v, 1.1v, 3.3v, 5v, 1.8v
It is feed by 12v supply which is also directly connected to the hard disk.
So it is possible to fix.. !! Only got to be a bit crazy.

I have a late 2008 Macbook Pro last updated to Mavericks OS. The screen died and it's not worth replacing. How do I remove the hard drive and use a drive sled to access info I need?

I have a late 2008 Macbook Pro last updated to the Mavericks OS. The screen died and I took it into an Apple store and was told replacing the screen and the hardware to repair everything would cost almost as much as buying a new laptop or a cheaper model. I was told that I can use a drive sled to access data I need on my hard drive. How do I remove my hard drive and use a drive sled to get to the information I need? What makes matters more complicated is I need to update my iPhone and my iTunes/App store purchases. How can I accomplish this?
My wife has a late 2008 Macbook Pro as well, which I am assuming I need to run my hard drive. Is there a way to just access just my hard drive without interfering with hers?
I know this is lengthy. Thanks to whoever looks at this and offers advice/instruction.

the device you need is an External enclosure for a 2.5" (laptop form factor) SATA drive.
A USB-interface enclosure will be slow, but is adequate for this task and for re-purposing as a backup drive later. A firewire-interface drive would be faster, but is harder to find, more expensive, and faster than needed for this purpose.
The drive will mount as an "extra" drive on your wife's Macbook, and you can drag and drop whatever you wish. You could create a separate Account for yourself on her computer, and use Migration Assistant or just copy your stuff over to the new account. Then it would not interfere with her files.

How can I erase the data on my 2009 macbook pro that won't turn on because of a faulty motherboard? Do I just remove the hard drive, install it in a working mac, and erase it that way?

How can I erase the data on my 2009 macbook pro that won't turn on because of a faulty motherboard? Do I just remove the hard drive, install it in a working mac, and erase it that way? Thanks.

You put the internal drive in an enclosure. If you choose to keep the drive, you don't need to erase it.
(110687)

MacBook pro boots to prohibited sign and apple has replaced the Hard drive and it's still didnt fix. They want to replace the hard drive AGAIN?!

I've had this issue for almost a month now, and they have tried multiple things to fix it from software re-installs to wiping the drive and they replaced the hard drive and cable but now that it is still not working they are suggesting installing another hard drive after it clearly didn't work the last time they replaced it. Help! I've contacted customer relations and the only thing she told me over and over is that they are working diligently to fix it. I'm a music teacher and that is currently the only computer i have and I use July to prep all my lesson plans and music. School starts august 18th and I feel like I'll be back in the store with the same problem again right when school starts. Any suggestions, ill probably be writing a letter very soon, any other suggestions?
Btw I have tried not backing up from time machine to rule out the possibility of something of mine corrupting it and it still did it.
Thanks for your help apple community!
David

Wholly Crap, No Joke, the lady from the apple store called me up at like 5pm and said "You know what?" and my reply was....... "what" and she goes, "You've been very patient and we understand you've been in and out in the last 3 weeks so we've decided to just give you a brand new computer" She gave me a brand new MBP! SO FREAKIN STOKED, my 2008 macbook pro for a new 2011 2.2ghz with 4 gigs of memory (Upgradeable to 8!!) The only downside is that since I use this for recording audio with Pro Tools well as recording audio with Pro Tools I needed the 7200rpm drive like my last one, and with her eyes i felt the "Beggars Cant be choosy" look flow upon me. But I shrugged it off and She actually told me to take this one, use it for the next week while the one she is ordering for me comes in!! So Bottom line IMHO (first time i've ever used that acronym in a forum) Apple Definitely has some awesome customer service!!
--this is one of those posts that I usually read and say "***, why cant that be me!!"
I <3 Apple.
David

If I upgraded my MacBook Pro from Snow Leopard to Lion via the web and now wish to erase the hard drive and restore it to factory settings to sell. How do I accomplish this?

I upgraded the operating system on my MacBook Pro from Snow Leopard to Lion via the web. Now I need to erase the hard drive and restore it to factory settings, so that I can pass it on. How do I accomplish this? When I insert the Mac OS X install disk, the only option is to erase the free space. Any insight would be appreciated.
Thank you

You need to boot off the original Snow Leopard DVD's that came with the system.
Once you are running off of the DVD you will be able to do a clean install of SL
To boot off the DVD with the system up running Lion insert the DVD. Open Sytem Preferences->Startup Disk and select the DVD then restart the machine.
Message was edited by: Frank Caggiano

Replacement Needed. This iphone is not able to complete the activation process and needs to be replaced. Please visit your nearest apple store or authorized service center.

Probably will never ever think of buying a locked phone from AT&T cause its one of the worst system integrations ever that these companies could think of.
The entire problem started when I put in a request with at&t to unlock my iphone 4s (ios7) which did get approved. I performed the entire instructions they asked me to do, which is to backup and restore. After doing those instructions my iphone gave me an error message below
The SIM card inserted in this iPhone does not appear to be supported.
The SIM card that you currently installed in this iPhone is from a carrier that is not supported under the activation policy that is currently assigned by the activation server. This is not a hardware issue with the iPhone. Please insert another SIM card from a supported carrier or request that this iPhone be unlocked by your carrier. Please contact Apple for more information.
Basically saying that at&t hasn't still unlocked the iphone which a really helpful apple executive was able to confirm. I initiated another unlock process from at&t in order to unlock the iphone, just to be sure that its not something wrong from my end. The nice at&t lady stayed on chat with me to unlock the iphone step my step while I was calling the apple tech too. And the apple tech confirmed again that the iphone is locked to at&t.
Now, just a few minutes ago I tried another restore to see if any progress is being made and to my surprise I got an error message saying
Replacement Needed. This iphone is not able to complete the activation process and needs to be replaced. Please visit your nearest apple store or authorized service center.
I feel like I am just going around these two different "money hogger" companies which set certain rules and regulations to screw a regular phone buyer. I purchased this iphone in USA and trying to unlock in India, is it really this hard to simply unlock a device.
For now I am going to try to call a apple office in india (apprently we don't have very many out here) and see if they can help me. But any other assistance regarding unlocking an iphone 4s would be helpful. I have however, tried checking IMEI.info, called up apple, talked to at&t (which always say go talk to apple) I do have a case number from apple as well in case an apple executive reads this discussion forum (case number: 566383594)
Thanks

You got a confirmation from AT&T that it was authorized. Is this correct? - Yes i did get an email authorization on the 21st.
Then you connected the phone to a computer with the latest version of iTunes installed. You clicked on the phone's name in iTunes, then clicked "Backup Now". - Yes
When that finished you clicked "Restore iPhone" (NOT "Restore Backup") - Yes
Are you with me so far? - Yes.
And @ Varjak is right that after the 3rd restore I get the replacement error.
Plus I have NEVER jailbroken the iPhone. To give you another update, I spoke to a really nice apple tech in India who was atleast able to get me out of the replacement error by doing a recovery mode option. However, the lastest restore still gives me the same error
The SIM card inserted in this iPhone does not appear to be supported.
The SIM card that you currently installed in this iPhone is from a carrier that is not supported under the activation policy that is currently assigned by the activation server. This is not a hardware issue with the iPhone. Please insert another SIM card from a supported carrier or request that this iPhone be unlocked by your carrier. Please contact Apple for more information.
Message was edited by: jabgars

My 15in. macBook pro display won't turn on. it stays black. i hear the hard drive working but the display won't show anything :( Is there a way 2 reboot my laptop 2 try

My 15in. Macbook Pro's monitor will not turn on anymore. when i press the power button to turn it on, the hard drive and everything but the monitor turns on. it is just a black screen and it doesnt even look like its trying to turn on . Can anyone tell me how to reset or reboot my laptop? I wanna try to see if that will take care of the issue before i drive an hour to the Apple store and have to pay xxx amount of $$$s for thm to tell me i need a new laptop. Please HELP!!!

try a reset first. Shut down, unplug for at least 15 seconds then plug and wait 5 seconds and restart.

My 2009 MacBook Pro keeps restarting even after I wiped the hard drive and reinstalled OSX.

About a month ago, my laptop started to randomly turn off: I would be using either Chrome, Photoshop (the free CS2 version available from Adobe's website) or Powerpoint, and the screen would go blank. I would then have to hold the power button for a while until the little light at the front of the computer would flicker and it would restart. I brought it to the Mac Store where they tested it and said it looked fine. They suggested I erase my hard drive and reinstall OSX as a precaution.
Fast forward a month, I have been very busy with work and hadn't been able to fix this problem. It wasn't that bad, only once every couple of days, sometimes more, sometimes less, I could work despite this problem.
Then, I installed OSX Mavericks. The installation started in the morning, but, like an idiot, I paused it to go to work. Later on, I completed the installation, it looked fine, but then all day long my laptop would suddenly restart and go to a grey screen that said in multiple languages "Your laptop restarted because of a problem, press any button to continue the restart." A computer technician friend of mine checked it out and said it was probably due to the badly installed OSX and suggested that I erase my hard drive and reinstall OSX.
I backed up all my files, erased the hard drive and reinstalled OSX. Everything looked fine.
Then it happened again.
Any ideas of why this is happening?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

On my Macbook pro 15 2011, System Profiler is suggesting that it uses SATA III for the hard drive and SATA II for the Optical Drive. Is that true?

On my Macbook pro 15, 2011, System Profiler is suggesting that it uses SATA III for the hard drive and SATA II for the Optical Drive. Is that true?

That is correct. The tech specs indicate:
Hard Drive Interface
6.0 Gbps Serial ATA (SATA)
Optical Drive Interface
3.0 or 6.0 Gbps Serial ATA (SATA)

I can't find how to redownload Acrobat Pro X. I had to replace my hard drive and have to reinstall all my apps.

I can't find how to redownload Acrobat Pro X. I had to replace my hard drive and have to reinstall all my apps.

http://helpx.adobe.com/acrobat/kb/acrobat-downloads.html

On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder

On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder

Welcome to Apple Support Communities. We're users here and do not speak for "Apple Inc."
Power on the computer and insert the DVD immediately.
Hold down the 'C' key to boot from the Snow Leopard DVD.
http://support.apple.com/kb/ht1533
After selecting the appropriate language, if necessary, select Utilities, and Disk Utility.
You'll likely need to partition and format the new drive before it's recognized.
http://manuals.info.apple.com/MANUALS/0/MA161/en_US/MacBook_13inch_HardDrive_DIY .pdf
(Yes, these instructions ARE 7 years old, but the procedure is the same for installing from DVD media.)

How do I retrieve my purchased songs and playlists from my iTunes account? I have just had to replace my hard drive and have lost pretty much everything!

How do I retrieve my purchased songs and playlists from my iTunes account? I have just had to replace my hard drive and have lost pretty much everything!

You can redownload your iTunes store purchases, but you'll need a backup to recover the playlists.

Have a old macbook 2006 with newer 500 GB seagate Momentus hard drive. I took mac to apple store and they said logic board is bad. Can I purcase another used macbook and install my old seagate hard drive and have saved my information? Thanks for any imput

Have a old macbook 2006 with newer 500 GB seagate Momentus hard drive. I did not backup any docs or pictures. The macbook crashed my fault. I took mac to apple store and they said logic board is bad. Can I purcase another used macbook and install my old seagate hard drive and have saved all my information? Thanks for any imput.

mgott55 wrote:
Can I install my used existing hard drive in a compatible macbook to save everything?
If you need to extract the drive's content you can remove it and install it in a $10 USB enclosure. It will be readable by any recent Mac.

My MacBook pro motherboard needs replacing (expensive!!), would I be able to remove the hard drive and have it put into my partners MacBook air?

Similar Messages

Maybe you are looking for