My Macbook Pro Retina's USB port on the right side not working at all

Dear all,
I received my macbook pro 15inch with retina display a week ago, but not until today had I got the chance to use the USB port on the right side, only to find out that it is not connecting to anything at all. I have tried to use my iPhone 4 and iPad 3 with two different cables, my USB thumb drive, and my Blackberry 9900, none of them are charging nor shown in iTunes/Finder. All of above works on the left and on other windows machines too.
I'm also not able to charge my Blackberry with the usb port on the left side, thought it would pop up a message saying "charging not supported" on the phone.
For you information, I have applied both updates including the one released few days ago. I have also tried to reset the PRAM. Also, I have migrated from my old late 2008 13inch unibody Macbook using Migration Assistant, not sure if this would affect anything.
I'm aware that there have been reports and discussions regarding the USB port not been able to run devices on 3.0 speed, but I wonder if anyone else have the same problem with me, where the port simply not connecting to anything at all?

I also have a problem with the USB port on the right side of my Retina MBP.  The USB3.0 port on the left side works fine, even with high speed external SSD enclosures, like the OWC Mercury Extreme Pro 6G which enables me to copy large files at a sustained rate of 160-170MB/sec.  Wow USB3.0 and the Mercury SSD is a FAAAAST combination connected to the Retina MBP.
However, like the forum entries about the USB3.0 ports in general on the new Retina MBP, the USB3.0 port on the RIGHT side is plagued with dropping intermittently, disconnecting my external hard drives while copying large files AS WELL AS disconnecting while just sitting there connected to an external hard drive and doing nothing.
Therefore, since I don't feel like returning my Retina MBP and waiting weeks for a replacement, I have chosen to only use the left side USB3.0 port for now.
I have my suspicions about why the right side USB port might be more problematic than the left side one.  I found this older post on the internet about how "Not all USB ports are created equal on MacBooks..." that talks about how on older models of MacBooks one of the USB ports shares a USB hub with multiple other devices like the iSight camera etc. therefore making it less tolerant of heavy traffic or something like that.  (http://www.wired.com/gadgetlab/2008/05/the-macbook-all/)
Therefore, I wonder if the right side USB port is sharing a USB internal hub where-as the left side one is more 'dedicated' and therefore in my case able to handle the high speed transfers/traffic I am throwing at it with my external SSDs.
I have also read that USB3.0 in general, on non-Macs, has had trouble for years.  For instance, some forum entries on Apple Support Communities and other non-Apple forums has made mention that 'they' are not surprised at the problems encountered on USB3.0 external hard drives connected to the Retina MBP because Windows laptops have had a lot of flakey problems with USB3.0 for 'years'. 
Also, I have recently purchased a "Buffalo" external Thunderbolt 1TB drive from OWC and have been doing Clones onto that drive for several weeks.  I use SuperDuper to clone >600GB of data on my 768GB Retina MBP several times a week.  And, I have (knock on wood) not had any problems with the stability of my externally connected Thunderbolt drive.
So, in my case, I am racking it up to high-speed stresses on the USB3.0 ports at least in part...and perhaps the possibility that the LEFT side USB port on the Retina MBP is more dependable and/or a more dedicated USB port than the right side one.
This doesn't really solve your problem, but it may at least help you feel like you are not alone.

Similar Messages

  • Macbook pro Retina display USB port right is 2.0?

    I got a new macbook pro with retina display. It says on the website that there should be two USB 3.0 on both side. I have a external hard drive that is 3.0 USB i plug it to the right side and the colour indicates that it is a USB 3.0, plugging it to the right side, turned green and that indicate a 2.0 Instead. So what is going on?

    I actually had the same experience this morning as you described. I plugged my USB 3.0 WD My Passport external drive into the left port (right port empty) and it negotiated to USB 3.0 (USB 3.0 SuperSpeed bus). After I ejected the drive, unplugged it; then plugged it into the right port it negotiated to USB 2.0 (USB 3.0 High Speed bus). So, I unplugged the USB cable from the right port and rebooted. This didn't fix it.
    The solution for me was to leave the USB cable plugged into right port and unplug the end to the device. Then plug it back in. After doing this, the drive in the right port negotiated to USB 3.0. I followed the information in this Apple article.
    USB 3 devices are not activating or not appearing on the USB 3 bus. What could be wrong?
    Sometimes unplugging and plugging the device back in can resolve the issue.
    Try plugging the device into another USB port on the computer.
    Try restarting your computer.

  • Just started my new Macbook Pro, from Time Machine backup and the password is not working

    Just got home with my new mackbook pro, and going through the startup process I booted from a time machine back up of my 2007 macbook. When I got to the login part of the process, after the new macbook was registered and ready to go, and now my password is not recognized.

    Sorry about that.
    I just got done posting back and forth with someone with a similar problem (not exact).
    Turn the power off by holding down the power button, that is if just one push does not turn it off.
    Then turn it back on and hold down the Option key. That will give you a startup screen where you can select which partition on the drive to boot into. Select the Recovery partition. From there you can use Disk Utility to wipe the Macintosh partition of the drive and then do a reinstall of the OS from the Apple website.
    You need a internet connection to do this and depending on your internet speed it can take a few hours to complete. If you have a fairly fast internet connection it may still take 1-2 hours to download the 3.5+GB file to do the reinstall.
    Before you go through all this try turning the system off and back on a few time to see if Lion can recover on it's own. I doubt it but it's worth a shot.
    Again sorry for the condescending tone.
    Happy New Year.

  • The USB ports on the right side are not working.

    HP G71-340US NOTEBOOK

    tstevenson08,
    It sounds like a hardware issue honestly, as discussed in a previous thread regarding this issue.

  • I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV?

    I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV? I have a MiniDisplay Port to VGA adapter, but there are two issues with it: The new display doesn't have a VGA port, and even if it did, I wouldn't want to have my mac constantly attached to the display by a cable. I was looking for a way to use the TV as a display without any wires. Is there some type of bluetooth setup I could use? Please let me know if you have any suggestions.

    As I wrote above, I think you should look into the Apple TV yourself. The best place to find information about what it can and can't do and to ask your own specific questions is probably in the Apple TV forum, here:
    https://discussions.apple.com/community/appletv/appletv

  • My left shift key on Macbook Pro Retina (15") is behaving like the F11 key (show/hide open windows).  The key behaves the same for the laptop keyboard and for an external Apple keyboard?  This just started in last week after 6 months of use

    My left shift key on Macbook Pro Retina (15") is behaving like the F11 key (show/hide open windows). 
    The left shift key behaves the same on the laptop keyboard and on an external Apple keyboard. 
    This just started in last week after 6 months of use.  The right shift key and other keys on the keyboard all appear to work correctly.
    Suggestions greatly appreciated.

    I have a solution to this issue now after a discussion with Apple Support.  Some where in the last few weeks, there was a change in the key that would do a Show Desktop under the Mission Control settings in the System Preferences.  Even though the key sequence that was shown for the Show Desktop setting did not include the Left SHift key, by changing this first to having no key sequence and applying that and then changing it back to the F11 key, the Left SHift key issue that I was having has cleared up.
    A second issue that was uncovered was that the SSD had some issues (uncovered when I ran Disk Utility using the Repair Disk key).  I had to restart and use the Disk Utility through the Command R sequence to get to the stand alone Disk Utility.  The SSD appears to be running better as a result as well.
    Hope that this is of use to someone else in the future.

  • MacBook Pro Retina 13" - Can i upgrade the dual-core i7 to quad-core i7 CPU?

    MacBook Pro Retina 13" - Can i upgrade the dual-core i7 to quad-core i7 CPU?  (obviously not talking about BTO, but about "self-service" upgrade ...)

    Yeah it is soldered. So no upgrade possible. Found here: http://www.everymac.com/systems/apple/macbook_pro/macbook-pro-retina-display-faq /macbook-pro-retina-display-processor-ram-expansion-slots.html
    Thanks Jon P D !

  • My macbook pro retina 2014 has crashed for the 2nd time in 2 mo

    My macbook pro retina 2014 has crashed for the 2nd time in 2 months. Can't get past the gray/apple screen.  The first time the genius bar tried all the different tricks to get it to boot all the way through, but in the end had to reinstall mavericks.  They said there weren't any indications of it being a hardware issue after running diagnostics.  The only possible reason is that it has something to do with some ProTools 10 plugins which I had downloaded in both occasions less than a week before.  I don't believe that would be the issue and I'm guessing it's a hardware issue at this point.  It's still under a factory warranty, so I'm not too concerned.  Thoughts?

    Try SMC and PRAM resets:
    http://support.apple.com/en-us/HT201295
    http://web.archive.org/web/20140711222006/http://support.apple.com/kb/ht1379
    If no success, try booting into the recovery partition and select Disk Utility from the 4 option menu.
    Run Disk Utility>First Aid, Verify and Repair.
    Any Change?
    Ciao.

  • Why does my macbook pro retina display shutdown while entering the administer account

    why does my macbook pro retina display shutdown while entering the administer account

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and  Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Usb 2.0 port on the right side (beside thunderbolt port) of macbook air 13" 2011 is busted, one of the pins inside the usb port is bent, is this replaceable? saw the pix on ifixit that it is part of the logic board.

    usb 2.0 port on the right side (beside thunderbolt port) of macbook air 13" 2011 is busted, one of the pins inside the usb port is bent, is this replaceable? saw the pix on ifixit that it is part of the logic board.

    The fix is a new logic board. It might be tempting to turn off the computer and start poking around inside to fix it yourself but you risk separating the port from the logic board and doing even more damage.

  • Does the battery charging in the macbook pro retina automatically cut off when the battery is fully charged?

    Does the battery charging in the macbook pro retina automatically cut off when the battery is fully charged? or does it continue charging?In which case,is it better for the battery life to switch off the power supply or leave it on while using the macbook?

    Yes, and the pilot light on the MagSafe2 connector changes from orange to green. If you unplug, you will start draining the battery again, whereas if plugged the Mac will take power from the brick and leave the battery in a charged state.

  • My problem is that one of the USB ports and the device does not detect this and inactive but can not find how to reactivate.Help me please! greetings thanks!

    Hello good evening, I have a MacBook Pro and my problem is that one of the USB ports and the device does not detect this and inactive but can not find how to reactivate.
    Help me please! greetings thanks!

    Do you have the Firefox new tab page but the actual sites are missing, or do you have some other page?
    If you have some different page, try the quick fix in Fred McD's reply.
    If the sites are missing, did you use the Reset feature? That will clear the storage associated with the new tab page. I'm not sure it's possible to recover from that; you probably need to rebuild your page from scratch as you browse.
    For possible future reference, here is how to access the hidden setting for the page to display on new tabs:
    (1) In a new tab, type or paste '''about:config''' in the address bar and press Enter. Click the button promising to be careful.
    (2) In the search box above the list, type or paste '''newtab''' and pause while the list is filtered
    (3) Double-click the '''browser.newtab.url''' preference and enter your preferred page:
    * ''Page thumbnails (default)'' => about:newtab
    * ''Blank tab'' => about:blank
    * ''Built-in Firefox home page'' => about:home
    * ''Any other page'' => full URL to the page
    Press Ctrl+t to open a new tab and verify that it worked. Fixed?
    Some gotchas:
    ''If Firefox won't let you edit this setting:'' you may have something called SearchProtect on your system.
    ''If Firefox lets you save your change but ignores it:'' one of your extensions may be overriding it. You can review, disable, and/or remove extensions on the add-ons page:
    "3-bar" menu button (or Tools menu) > Add-ons > ''in the left column click'' Extensions
    ''If the change works during your session, but at the next startup is back to an unwanted page:'' you might have a user.js file in your personal Firefox settings folder (your Firefox profile folder). This article describes how to track down and remove the file: [[How to fix preferences that won't save]].
    Any luck?

  • I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone an i have internet and all other functions working on my computer

    I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone and i have internet and all other functions working on my computer

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    Step 1
    Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
    Step 2
    In the Console window, look under User Diagnostic Reports (not "Diagnostic and Usage Messages") for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents—the text, not a screenshot. I know the report is long. Please post all of it anyway.
    In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
    Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

  • HI, I just got a Macbook Pro.  It's great but my mail doesn't work at all.  It will come up correctly, but take forever to download messages,  then won't delete them,  then won't save them to folders.  Then when I go to quit mail it's like it gets stuck.

    HI, I just got a Macbook Pro.  It's great but my mail doesn't work at all.  It will come up correctly, but take forever to download messages,  then won't delete them,  then won't save them to folders.  Then when I go to quit mail it's like it gets stuck between quitting and not.  I have to force quit, then restart my computer if I want to pull up my mail again.  How can I fix this?

    If you just got your new MBP you have phone support from Apple (which is quite good) call them.  800-692-7753 tell the automated answerer "mail technical support" you'll have human quite quickly.  Hope this helps.

  • I bought new Macbook Pro 13" around two months before .My Apple ID is working on all other things except app store . It is buffering for a lot of time and lastly coming on screen " can not connect to app store " Please help me

    I bought new Macbook Pro 13" around two months before .My Apple ID is working on all other things except app store . It is buffering for a lot of time and lastly coming on screen " can not connect to app store " Please help me

    Have you tried repairing disk permissions : iTunes download error -45054

Maybe you are looking for

  • Library crashed how do i move the apps on my touch to new library

    Long story short, the volume structure of the external hard where my itunes library was located disintegrated. Not all was lost, as I happened to have copied all of my music onto my wife's itunes (running on a separate external hard drive) so i still

  • Html form page navigation

    Both attachments are renamed as .xml files to allow upload. Rename as .xdp to test. I have attached two example .xdp files which I have been testing under FormsIVS 8.2 rendering as auto detect html. The file [paging test 1.xdp] consists of 5 top leve

  • Putting Oracle Apps 11i on 10g RAC using VMware

    Hello All, I am building a Oracle Applications 11i on 10g RAC, using VMware..Since there aren't any docs I could find on internet explaining how to do this, I have come up with my own. I have combined the MEtalink doc:362135.1 and the docs describing

  • Error in when No file selected For Upload Form

    Is there a way to create an upload form that when no file is selected to be uploaded will not return an error message even if the submit button is clicked? Thanks, Craig

  • Installing itunes9 after itunes10 has been released

    I have a machine that can not run 10.5 so I can not have itunes 10. where can i find the itunes9 install package?