My macbook pro will not charge when I am using it.

My macbook pro will not charge when I am using it. My battery will say "charged" then "not charging" and it goes back and fourth. It says "Power Source: Power Adapter". But when I use my pro it will loose the power source then reconnect a second later to it. This problem is getting annoying because I have to stop using my macbook pro to charge it.

Reset SMC.
http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
If this does not help, contact Apple.
Best.

Similar Messages

  • MacBook Pro will not charge when Computer is on. Can only charge when shut down, MacBook Pro will not charge when Computer is on. Can only charge when shut down

    Hi can anyone help me? My MacBook Pro cannot charge at all (keeps showing not charging or not connected) when i am using it. only when i shut it down or let it sleep then wil it begin to charge normally. Does anyone know what to do??

    You could always try a SMC reset -> http://support.apple.com/kb/HT3964 - but I don't believe that will solve your problem.
    If I were you, I would take the machine to your local Apple Store or an AASP and have them diagnose the problem. It could be something very simple or it may be something more complex within the power management system.
    Good luck,
    Clinton

  • MacBook pro will not charge even when the charger is plugged in and working

    So this is a strange one.
    I have been using my MacBook pro for a lot of film editing and motion graphics. Recently, I noticed that my battery kept going down, even when charging. I thought nothing on it and kept using it. After around 4 hours, the battery went from 90% to 23% WHILE plugged in. This got me nervous. When I plug in the MagSafe charger, the light comes on and I get the "charging" symbol in my toolbar. The light turns orange and then, after a few minutes, the power starts to go down instead of up.
    I have had this laptop since Christmas 2012 and this has never happened before. The laptop does charge, but only when I am running no application, when the screen is shut or when the laptop is powered off. Bear in mind that right now, I am on Firefox, that is the only application open, yet the charge is still going down. I assumed it was because I was using Premiere CS6, After Effects CS6 and Cinema4D, but now even when they are not open, the batter will not charge when I am using the laptop.
    What is going on? Is in the charger? Any help would be greatly appreciated and I am starting to stress!
    Thank you everyone for reading,
    -Rory Campbell
    UPDATE: I am currently only running Firefox and Finder. Now the laptop is charging as usual. However the second I open up Premiere, After Effects etc, it goes down. I have no idea what is going on!

    Try resetting the PRAM and SMC. If you don't know how to, don't worry. They're very easy to reset. Just google how to do it. If that doesn't work, the only thing I would suggest is to take both the laptop and the charger to your local genius bar to have them examined. If it's less than a year old, apple should replace whatever is wrong with it as long as it was a factory defect.

  • My macbook pro will not charge or turn on. When I plug in the charger nothing happens and the light doesn't turn on. What can I do?

    My macbook pro will not charge or turn on. When I plug in the charger nothing happens and the light doesn't turn on. What can I do?

    Some basics please, what vintage is your MBP, have you plugged anything else into the wall socket to verify that it is live? which light doesn't turn on, the charger or the MBP?
    Hold the power button down for 15 seconds, wait for 2 then press it normally and see te MBP it turns on

  • My Macbook Pro will not charge. I have tried other charges and nothing. Can the MagSafe port go bad? Is that expensive to repair?

    My Macbook Pro will not charge. I have tried other charges and nothing. Can the MagSafe port go bad? Is that expensive to repair?

    The port can fail. Internal boards can fail. Batteries can fail. All with the result that no charging occurs. 
    You can try Resetting the System Management Controller and you can try Troubleshooting MagSafe adapters. 
    But usually you will have to take the mac in to a service place for testing.  It can get expensive, although occasionally it is not.
    charlie

  • The battery of my macbook pro will not charge and the LED light is only green. What to do?

    the battery of my macbook pro will not charge and the LED light is only green. What to do?

    This might help:
    Intel-based Macs: Resetting the System Management Controller ...
    Otherwise, you should probably take your computer in to a service place to be tested, since there a a few possible causes of this behavior.

  • My macbook pro will not charge. the charger blinks with a dim green light and the computer will not turn on

    my macbook pro will not charge. the charger light is dim green and blinking.

    Please make a Genius Appointment and take it in for service.You may have a bad charger, battery, or worse.

  • MacBook Pro will not sleep when charging and display is closed.

    Hi,
    My Mac will not sleep when it is charging. When I close my display, it will not sleep.
    When I unplug the power cable, it sleeps...
    I've tried to reset the SMC, and I think i did, the charger went from green to red etc different colours..
    Does anybody know what this might be?
    thanks

    AIGHT GUYS!
    This is how to fix it, and i guarantee u its 90% the cause.!
    first of all, if you are a lion user (most likely all of you with this problem) go to system preferences, and then to sharing. turn all sharing OFF. especially printers....
    open a terminal, and type in :
    pmset -g assertions
    This will show u if somehting is preventing ur mac from sleeping. on the left colomn, it should say "PreventSystemSleep" and on the right colomn a number. mine was one, which is probably the same for you guys.
    Go to system preferences > Print & Scan > Open Print Queue. Make sure all the printing queues are empty and nothing is in there. You do not need to pause any or anything like that just make sure nothing is in the queue.
    Close your macbook lid and look at ur light it should be sleeping. HOPE THIS WORKS FOR U
    took me long enough to find out.
    dont hesitate to ask me any questions

  • My MacBook Pro will NOT charge with a MacBook Charger.... TEMP FIX.

    ALRIGHT as you could tell from the title I can not describe it all in the heading...
    I own a 2008ish 17" MacBook PRO and I forgot my charged in Western CAnada and I have my 13" MacBook (NEwer cord style) anyway its a 65Wt instead of the 85Wt... MEANWHILE it charged my MacBook Pro for a while but NOW it will NOT Charge it at all and my MacBook Pro is absalutely DEAD as a door nail right now!
    IS there a reason why my 65Wt cord will not charge it AT ALL!? when it once did...??? I should be getting my regular cord back in less then a month... (Living in quebec)
    HELP!

    Please make a Genius Appointment and take it in for service.You may have a bad charger, battery, or worse.

  • My MacBook Pro will not charge.

    Hi Apple Support Communities!
    I have a 2006 MacBook Pro 1,1.
    This computer is equipped with an Intel Core Duo processor, and 2 gigabytes of 667 DDR2 SDRAM.
    It works absolutely fine, but I am having small problem with it: it will not charge. Since it is from 2006, Apple considers it to be "Vintage and Obsolete." I have no idea what is wrong with it, and am in need of it in proper working condition by this August. I do not have the original install discs for it, and have no way of running the hardware test to see if there are any problems. What do you all suggest? Thank you in advance!
      Model Name:          MacBook Pro
      Model Identifier:          MacBookPro1,1
      Processor Name:          Intel Core Duo
      Processor Speed:          2 GHz
      Number Of Processors:          1
      Total Number Of Cores:          2
      L2 Cache:          2 MB
      Memory:          2 GB
      Bus Speed:          667 MHz
      Boot ROM Version:          MBP11.0055.B08
      SMC Version (system):          1.2f10
      Serial Number (system):
      Hardware UUID:          00000000-0000-1000-8000-0016CB9674E1
      Sudden Motion Sensor:
      State:          Enabled
      Model Information:
      Manufacturer:          SMP
      Device name:          ASMB012
      Pack Lot Code:          0001
      PCB Lot Code:          0021
      Firmware Version:          0010
      Hardware Revision:          001f
      Cell Revision:          7a3e
      Charge Information:
      Charge remaining (mAh):          0
      Fully charged:          No
      Charging:          No
      Full charge capacity (mAh):          5028
      Health Information:
      Cycle count:          2
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          0
      Voltage (mV):          5500
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          180
      Automatic Restart On Power Loss:          Yes
      Wake On AC Change:          No
      Wake On Clamshell Open:          Yes
      Wake On LAN:          No
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      Battery Power:
      System Sleep Timer (Minutes):          10
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          2
      Wake On AC Change:          No
      Wake On Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          85
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x002582ae
      Charging:          No

    joncwyatt,
    you can contact Apple directly to purchase a replacement pair of grey DVDs for your MacBook Pro, which has (among other things) its model-specific Apple Hardware Test. (The Apple stores don’t stock the grey DVDs.)
    Was your new battery sold by Apple, or was it manufactured by a third-party? Have you tried purchasing a different battery for your MacBook Pro, to make sure that the problem is not with the new battery currently in your possession?

  • My MacBook Pro will not charge (no light on adapter)

    I've been trying to charge my macbook all day, but it will not charge - the adapter light (green or amber) will not even turn on, and the computer is cold. Is it likely the adapter, battery, or something larger?

    Hi  jsfisher13. Will your Macbook Pro start up with battery and power cord attached? If so, download coconut battery app. I will give you a link. I have a 2009 Macbook that my daughter uses and it does not show as charging and will not run with battery removed. What I found is, that with coconut battery app, the Macbook was charging . But it was so slow that it would not show in the apple systems power or at the battery icon on the top menu. The charge rate was between 2.5 and .3 amps.Should be at least 12 volts. or 23 amps. Her Macbook took 8 hr. to go from 30% to full charge. If you can not see any green at all on the mag safe power adapter, even a very faint green you might have a defective dc in board. That is what you are plugging the mag safe into. It plugs into the logic board. You would have to take it to the apple store to have them run a test on it.http://www.coconut-flavour.com/coconutbattery/

  • Macbook Pro will not charge.. Help

    My macbook pro got a some water spilt on it so I put a fan over it and and used rice to try to dry the moisture. The computer itself works fine everything works like it normally would except that it will not charge. It recongizes that the charger is connected to it but says it's not charging. The charger itself isn't the problem because I tried another charger and it didn't work either. Is it the battery or is it something else that doesn't work? I'm pretty despirate for help and I don't have any warrenty on it so I don't want to call Apple if I don't have to and pay $50 for them to tell me that something is wrong..

    try an smc reset see if that works here is an apple link that will explain you how to do so http://support.apple.com/kb/ht3964

  • My MacBook Pro will not charge, even after resetting the SMC.

    My MBP will not charge. It's only a little less than 2 years old. I've reset the SMC and even an employee at the genius bar has, it still isn't charging. When I plug in the cord, my battery remains at 13% with a plug icon inside the battery. When I click on the battery, it says "Battery Not Charging" in gray.
    This is my battery information:
    Battery Information:
      Model Information:
      Serial Number:          9G1300072D3MA
      Manufacturer:          DP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          2
      Cell Revision:          158
      Charge Information:
      Charge Remaining (mAh):          685
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          5448
      Health Information:
      Cycle Count:          336
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          0
      Voltage (mV):          11099
    Please help!!

    When I plug in the cord, my battery remains at 13% with a plug icon inside the battery.
    Try  Troubleshooting MagSafe adapters
    And try a different electrical outlet.

  • MacBook Pro will not charge, hold a charge or even turn on now.

    My charger was/is not charging my battery. I have tried other chargers that have worked for me in the past couple months when my original charger went bad but now my computer will not charge at all. The amber light shows, but I cannot turn on my computer even hours after letting it "charge."
    When I first plug the charger into my MackBook, the green light comes on for about 5 seconds and then switches to orange.
    I press the power button to see if the comupter will turn on while charging and it will not.
    What should I do from here..
    Thanks for the help!

    The MBP should work when the charger is attached (assuming the charger is functional).  Try a SMC reset:
    http://support.apple.com/kb/ht3964
    If that fails to bring life to the MBP, bring the MBP to an Apple store genius bar for a free evaluation.
    Ciao.

  • My retina Macbook Pro will not charge, what are my options?

    I have a water damaged 15" rMBP, everything works fine and dandy except that it will not charge. Maybe it's the charger? The battery? The cable that connects the battery feeding power to the system? No idea. I can only use it if it's plugged in which is a HUGE bummer for me. I have Apple Care, but Apple obviously won't help me. I tried and they didn't, I don't think a different rep would make a difference . I know I messed up, but I've come to accept that fact at this point. I was wondering if there is anything I could try/fix/replace to get the charging working again? If there was water damage to the logic board wouldn't everything else stop to work as well? Theres gotta be something to try.. please help!
    I think replacing the battery would fix this, but I have no way to tell. Would apple do this since I have apple care? If I just asked them to replace the battery?

    Basically, you're just screwed. There are liquid sensors in the MBPs and the liquid damage would be obvious to any liquid damage. You'll just have to take your unit in and get a quote on how much it would cost to replace everything that needs replacing.
    I have renter's insurance with a $10,000 rider for accidental damage to computer equipment - maybe check with your homeowner's/renter's insurance company next time for just such an incident.
    Sorry,
    Clinton

Maybe you are looking for

  • Saving a Form created in Adobe Acrobat 9 Pro

    We create forms for the company to use with Adobe Acrobat 9 Pro, but because others do not have Acrobat 9 Pro they can not save the document after they have filled out the form.  This is causing a big issue for us.  Does anyone know a way that we can

  • X58 Eclipse Sli with CMP12GX3M3A1600C9 how to make it run stable in 1600Hz?

    Hello , I m new here, so forgive me if i make a mistake somewhere ! So my specs are : motherboard: X58 Eclipse Sli(bios ver:1.F0 model:MS-7520) CPU:i7 950 @ 3,07 (stock) GPU: 2x GTX470(msi) PSU:Thermaltake 1200watt HD:1xSSD , 1xWD@10000rpm and here i

  • Please help with 3d tv purchase!

    okay i went out on a limb and purchased a lg 55lw5300 3d tv from best buy. it came with the four glasses and blu ray player. I am sorry to say i did miminal research before purchasing this item due to time issues (i know it was dumb). my question is

  • How to smooth out a credit roll

    Hi, Using FCP X on a MacBook Pro and haveing touble creating a smooth credit roll. Rufus

  • Windows jump to front?

    Hey everyone! Recently purchased a MBP with Lion pre-installed. I noticed a weird (and extremely annoying) bug. I would be using an app, then all of a sudden another open app's window would "Jump to front"... as if I had activated/interacted with it.