My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg():Socket is not connected
My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected
If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages.
Similar Messages
-
My iphone 6plus not working not charge but when i run it the first time working half an hour when you attempt to run it again light up thr screen and showws the apple logo and after the pice screen illuminates red and does not work what do i do now
Hello Nadersalah,
It seems you're experiencing multiple issue with your iPhone. Based on the information you have provided, it appears your iPhone needs to be serviced. The following link should help you get started with the process and has links with additional information on topics such as warranty and service pricing, battery replacement, and express replacement service.
iPhone Repair and Service - Apple Support
Thank you for contributing to Apple Support Communities.
Cheers,
Bobby_D -
While updating my MacBook Pro to the newest software, it froze with a grayish screen with a Apple logo and a frozen pinwheel right below it. What can I do to finish updating or to fix this problem?
We can't help you if you don't even know what you are installing. Never install anything if you do not know what it is. Installings through Software Update always have explanations which you should be reading to see if you actually need and/or want them.
That being said, it appears you attempted to upgrade to Mavarick. Although I am not positive.
Sorry, I am going to back out of this because I nor you know what it was you installed. Hopefully, someone else will chime in here.
GOOD LUCK! -
Help, Turned on MacBook Pro this morning and just get a white screen with grey apple logo and spinning gear. Cannot access desktop.
Computer starts up in Safe boot by holding down the shift button. But when I go to restart the same thing happens. What should I do?
-
For the first time, I'm trying to use adobe premiere elements 10 that came with my pc Windows 8. I created a single project, saved it but cannot open it. My pc shows the file I created but I get an error message that says this type file is not supported or the codex is not installed. As a test, I created another very small project and get the same error message, when I try to open it. Pls give me a simple answer, a refund or a phone
mike frischenmeyer
What computer operating system is your Premiere Elements 10 running on? And, what video card/graphics card does that computer use?
Is this the first time you are using Premiere Elements 10 or have you worked with it before successfully? There is no easy solution until we
know the details and troubleshoot to determined what caused the problem.
1. Can you open a new project?
2. After you saved/closed the problem project, did you move, delete, or rename any of the files/folder that were related to the source media
for that project?
3. Please review the Adobe document on troubleshooting damaged projects.
Troubleshoot damaged projects | Adobe Premiere Elements
4. What are the steps that you are using to reopen this saved closed project.
a. File Menu/Open Project/Name of Project
b. Other
Please review and consider and then we can decide what next based on your further details and results..
Thank you.
ATR -
my 27 inch 2011 iMac is not boting up, the cumputer is stuck on a grey screen with no apple logo or spinnign wheel. The iMac is not giving power to the keyboard as it is not ligthing up the caps lock botton when pressed.
Contact Apple Service, iMac Service or Apple's Express Lane. Do note that if you have AppleCare's protection plan and you're within 50 miles (80 KM) of an Apple repair station, you're eligible for onsite repair since yours is a desktop machine.
-
Trying to uninstall itunes 11.0.4 in order to update to the most recent itunes. I get an error message that say..."This installation package could not be opened. Contact the application vender to verify that this is a valid windows installer package.
Hello JAH1961,
I recommend following the steps in the article below when getting an error message trying to install iTunes:
Trouble installing iTunes or QuickTime for Windows
http://support.apple.com/kb/HT1926
Thank you for using Apple Support Communities.
Best,
Sheila M. -
hello everyone, as I have stated above, I have an Iphone 4G realtively new, just 3 months of use. I've never dropped it, nor got it wet. The problem is that the screen just one day went black and displays the apple logo, when I do the recovery mode everyway possible the screen shows the itunes link but the pc doesn't acknowledge it.. I've tried on many pcs (windows and mac) and none respond because the device is not shown on itunes it just says "driver not found"
please what to do???Call Apple Customer Relations - 1-800-275-2273. Ask politely & firmly that you want to be transferred to Customer Relations. Tell them exactly what you stated in your post.
GOOD LUCK!
These are user-to-user forums where everyday folk (volunteers) post questions and offer answers (technical support) to each other. -
Hello, my phone was being slow so i turned it off. when i went to turn it back on it did the usually white apple logo but it has been on that logo for 15 or more minutes now what do i do?
First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
-
Macbook Air won't start up past the "apple" page, and has a spinning icon. help!
The computer was left on for over a week while I was out of town, came back and it was slow, then it started doing the "spinning beach ball" so I shut it down and now it won't start up again.
Hey Sarah.
The spinning beach ball of death is a tricky issue to fix.
You can delete everything in the caches folders located at:
~/Library/Caches
/Library/Caches
Also try an SMC/PRAM reset:
PRAM RESET:
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
SMC RESET:
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
If you still boot to the apple screen your next option is to boot to the Mac OSX install DVD and run a disk check/repair.
Hold down option with your OSX DVD in your drive, click on the cd that appears, boot to the OSX DVD.
Click on utilities in the menubar, go to disk utility, select Macintosh HD, run a check/repair.
If this fails you'll need to run the Max OSX installer and reinstall your Mac OSX.
P.s since you have a Macbook Air your install DVD is the usb stick you would have got with your MacBookAir. -
I get an error message that says power pc programs are not supported
I updated my Mac and now I can't open any of my Microsoft programs. What happened?
Lion does not support PPC applications. You will have to install newer versions or use them with Snow Leopard.
Ciao. -
I desperately need it to work again. please help!
What "Loading symbol" are you talking about?
-
Start up with a white screen with an apple logo keep on spinning
my imac 10.5.4 version won't start up it has white screen with apple logo and keep on spinning it's been 2 weeks now try to fixed it i tried everything no luck im trying the verbose what i see on the screen is that diskOs2:0xe0030005 (UNDEFINED) please help me !!!!
Hi Haziq0135,
Welcome to Apple Support Communities.
It sounds like your MacBook Pro is starting up to a gray screen with a Apple logo and a spinning gear. The article linked below provides a lot of great troubleshooting suggestions that should resolve issues like that.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
I hope this helps.
-Jason -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
on start up i just get a grey screen with the apple logo-this has suddenly started happenin. Please help?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
Maybe you are looking for
-
Need Affordable Capture Card CS4 Win 7 i5
I work for the government, so some things here are out of my control. In 2003, I was able to build a machine to capture TV news clips for an archive and to turn some material into web video. We also Firewire in our own material, edit and burn to DVD
-
ORA-27140: attach to post/wait facility failed
Hi We are facing following probelm on hp 11i /oracle 9i system ##ORA-27140: attach to post/wait facility failed Details Log As Below BR0002I BRARCHIVE 6.40 (15) BR0006I Start of offline redo log processing: adqqukeg.sve 2005-08-20 11.59.10 BR0280I BR
-
Having trouble with intial set up
having trouble with initial set up!
-
Pivot_root message during bootup
Hi all, During bootup just before INIT, the following message is displayed: pivot_root: pivot_root: Invalid argument I'm booting the 2.6.15-archck kernel. My pc seems to work fine. But why is this message displayed? Just curious. Cheers, Jules
-
Hi guys I want you to help me to understand the biggest differences between iPhone 5 and galaxy s3 .Why should I buy iPhone 5 ?