My MacBook Pro won't go past the white apple page

My computer won't go past the white apple page with the spinning wheel when you turn it on.

This should fix the problem:
Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Similar Messages

My macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

my macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Macbook pro won't go past the apple logo (Lion)

I've installed Java Runtime, and after that tried to use "software update" but the application quit.
Tried to restart, but it stays stuck on the apple logo (with the wheel turning) for ages. Restarted in recovery mode, ran disk utility, repaired permissions and verified disk. no problems found. Restarted again, still the same thing - won't go past the apple logo.
If reinstall is the only way to go, is there a way to access this hard drive to back up files (it is a recent computer, still hadn't made any backups...)
Thank you all, help would be much appreciated!

Shut down and startup holding command-r keys into Recovery Disk from there choose Disk Utility and Repair Disk.
polymolly wrote:
I've installed Java Runtime, and after that tried to use "software update" but the application quit.
Tried to restart, but it stays stuck on the apple logo (with the wheel turning) for ages. Restarted in recovery mode, ran disk utility, repaired permissions and verified disk. no problems found. Restarted again, still the same thing - won't go past the apple logo.
If reinstall is the only way to go, is there a way to access this hard drive to back up files (it is a recent computer, still hadn't made any backups...)
Thank you all, help would be much appreciated!
Ooops you've been there, done that. You can use Target Disk Mode if you have another Mac.
EDIT: Was the Java Runtime from Software Update?

The Macbook Pro will not start past the grey Apple logo screen? Any help will be most welcome?

The Macbook Pro 13, late 2009 will not start past the grey Apple Logo screen? Any help will be most welcome? Thanks

Have you tried booting with the install disc that came with your computer?
Find it and then run Disk Utility to verify your hard drive. If errors are found, try to repair the disk.
It sounds as if the hard drive might be failing.
Clinton

My macbook won't turn on past the white apple page?

When I turn on my laptop the screen goes to the white/gray page with the apple logo in the center. It does not load past this. What should I do ?

It allows to boot with just the Apple OS, to see if you have a problem with other things. If the safe boot works, in other words if your mac works ok then then there are some fixes that can be applied. While we are talking about it disconnect any peripherals when you do this, it can help to see if the peoblem is your mac or something else.
Don't worry it will not effect your data. If your Mac works fine in safe boot it means it is not the computer, rather something else.

Macbook pro won't boot, stuck on white apple screen

Noticed today, that my macbook pro won't boot . It gets to the white apple screen with the spinner under the apple logo. It stays like this for a long time without doing anything except spinning.
I've powered down and tried to boot up several times.
I have boot camp and windows on my mac and when the white screen appears, I can press Option to bring up which hard drive and the Windows partition will load without any problems.

Exacty what happens when you try to boot up from the disc that came with your computer? Are you holding down the c key? Have you tried holding down the "option key?" Are you able to run the Hardware Test - Intel-based Macs: Using Apple Hardware Test
Shut down your computer and disconnect all peripherals (keyboard & mouse if pertinent) from your computer. Now reboot.
If the Mac starts up normally, shut it down again and then plug in one of the peripherals (keyboard or mouse first) and start up your computer again. If it does so successfully repeat the process, adding one peripheral at a time until your Mac acts up. At that point, disconnect the last peripheral you added, reboot your Mac and search the peripheral vendor's website for an updated driver.
If no driver exists or the problem remain after installing the new driver, try a different cable or a different port on your Mac.
If none of the above works, again disconnect all peripherals from your Mac, hold down the "shift" key to start up in "Safe Boot" mode.
If the Mac starts up correctly, restart without pressing the "shift" key.
If your computer still does not start up properly, shut it down and restart it while holding down the Apple+Option-P-R keys; keep holding "all 4 keys" down until you hear the startup sound "twice."
If none of the above work Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
(If Disk Utility cannot repair, you will need a stronger utility (3rd party) - Diskwarrior or Techtool PRO)
Restart your computer when done.
Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.
Remove any 3rd party ram.
Reinstall Lion - This will install a "fresh" copy of Lion without archiving old system files but leaves the rest of your files in place.
If your computer is still under warranty or you have Apple Care, take full advantage of it by letting tech support deal with your problems. It's what you're paying them for.
Out of warranty - take the computer to an Apple store or an AASP. Whichever is more convenient for you.

My macbook pro won't load past the opening screen

i was using my macbook pro last night and it just froze, i turned it off and then tried to restart it. while restarting, i noticed that the screen had not changed for a couple of minutes. it was the screen when you first turn your computer on, before you log onto a user. i waited for about an hour and the screen wouldnt change. i've tried restarting it. nothing is working. any ideas?

Well, it would depend if your HDD has died. If you don't have a backup that would be unfortunate.
First, go grab your original install disk, stick it in, and restart & hold the C key.
That will bring up the install screen.
Select your Language.
Then go up the top to Utilities > Disk Utility > Repair Disk + Repair Permissions
Please take note of any errors it repairs / does not repair.

My MacBook Pro won't go past the grey screen. It only shows that it's loading and doesn't go any further.

Okay well, to start off, I got my MacBook from a distant family member who got a new one so they let me have their old one. They got it from a pawn shop so I don't have the disk that we got the OS from but it hasn't had any issues UNTIL NOW. I need to use my laptop for a homework assignment so please help me quickly. Everytime I turn it on it'll just stay on the loading screen, I left it for 4 hours yesterday and it still wouldn't work. I reset the (insert acronym here) thing already, the thing where you press control, option, P, R keys at start up. I really need help because my assignment is on the laptop and it's due tomorrow. Please help. ={ And I'm not entirely sure which OS it's using because I've never really checked.

Boot from the OS DVD you have for the computer.
Repair the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
You can reinstall OS X, but the procedure depends on the version of OS X that is installed.

MacBook Pro won't get past the apple screen on startup

The laptop won't startup. I get to the Apple logo and a spinning gear. I've tried starting it 3 times with the same result.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

MacBook Pro won't get past the flashing grey file screen?

Ok, so tonight I try turning my MacBook on as normal, it then froze and I saw the rotating umbrella appear. So I restarted it. When trying to turn back on, the system did not load, instead a flashing grey file shape came up with a question mark inside. I have tried restarting with a number of key combinations, Option; option, ALT, P, R. Everything, yet it's not getting past this screen. Whenever I try to do an Internet recovery, it just stays on the wifi selection screen and I select mine, enter the password and then it just goes back onto the selection screen. Nothing is work yet! Incredibly annoyed as it has so much stuff, photos, music everything. I don't even know how I reinstall software as it's stuck... Can someone please help? My software is 10.7 I believe.

Hi PHXSuns,
If you are seeing a flashing question mark on startup, you may find the following article helpful:
Apple Support: A flashing question mark appears when you start your Mac
https://support.apple.com/kb/TS1440
Regards,
- Brenden

My MacBook Pro won't connect to the Internet, but my phone and PC will.

My MacBook Pro won't connect to the Internet. My iPhone has no problem doing so, and neither does my PC. I think it's something to do with my DNS, but I'm not sure. My network connections say that both my Ethernet or FireWire are failed. What's wrong with my MacBook? Is there a simple way to fix this?

Hello Rattisate,
Sorry to hear you are not able to connect to Wi-Fi on your MacBook Pro. I would be concerned about this too. You can find information on how to troubleshoot this in the following article:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Follow the steps in the section labeled, "Symptom: My Mac does not connect to the Internet."
Thank you for posting in the Apple Support Communities.
Best,
Sheila M.

My MacBook Pro won't connect to the Internet via wifi but it worked fine on ethernet cord...I tried running diagnostic but it didn't work:(((( it happen every time if I restart the modem and/or router

My MacBook Pro won't connect to the Internet via wifi but it worked fine on ethernet cord...I tried running diagnostic but it didn't work:(((( it happen every time if I restart the modem and/or router.. Any idea how to fix this?

Hello Rattisate,
Sorry to hear you are not able to connect to Wi-Fi on your MacBook Pro. I would be concerned about this too. You can find information on how to troubleshoot this in the following article:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Follow the steps in the section labeled, "Symptom: My Mac does not connect to the Internet."
Thank you for posting in the Apple Support Communities.
Best,
Sheila M.

My macbook pro will not get past the gray screen with the apple logo and a loading bar.

My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours. I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck. Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.

You didn't say which OS in your tag, but maybe you might find something here.
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/PH4191
http://support.apple.com/kb/PH7213
http://support.apple.com/kb/HT4125
http://support.apple.com/kb/HT2213

My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!

My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

I have a new Macbook pro, I cannot get past the country selection screen. 'Continue' is greyed out and keys just make error sounds. How do I move it on?

I have a new Macbook pro, I cannot get past the country selection screen. 'Continue' is greyed out and keys just make error sounds. How do I move it on?

sideeque wrote:
I have the same problem. What did you do last time?
What should I do now? Its around 40 miles away the apple store? Would they pay my taxi fare to go and return?
How can we trust this apple product?
You are still under warranty. Call Apple Care.

My MacBook Pro won't go past the white apple page

Similar Messages

Maybe you are looking for