My MacBook Pro won't switch on and the battery charger light keeps flashing green and amber
Any suggestions of what I should do, my mac book won't switch on and there's a faint green and amber light flashing on the charger.
Sounds like bad battery
For more details, read https://discussions.apple.com/message/3884756#3884756
Allan
Similar Messages
-
My MacBook Pro won't turn on although the battery life is showing full
My MacBook Pro won't turn on although my battery life is showing full ,
Go step by step and test.
http://support.apple.com/kb/TS1365
Note: Steps 5 and 6
Step 5
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own". -
My MacBook Pro won't switch on.
My MacBook Pro won't switch on. I've tried charging it, but it wont detect the power (the green LED indicator won't light up). The pins are clean and the power source is fine. I've tried using a different charging cable, and the problem still exsist.
Please help!
Thanks.You can try Intel-based Macs: Resetting the System Management Controller (SMC). But if this doesn't help then you may have a hardware failure.
-
I recently did a full reinstall from my time machine and now my MacBook pro won't back up to the time machine. It starts a full backup ignoring the original back up, can anyone help?
Did you follow the instructions on the page linked below?
OS X Yosemite: Recover your entire system -
my macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?
Might be a problem with the adapter.
Help here > Apple Portables: Troubleshooting MagSafe adapters -
My MacBook pro won't start up and gives a beep
My MacBook pro won't start up and gives a beep
Look at these articles for possible assistance:
http://support.apple.com/kb/TA43884
https://discussions.apple.com/docs/DOC-3353
Ciao. -
Does the battery charging in the macbook pro retina automatically cut off when the battery is fully charged? or does it continue charging?In which case,is it better for the battery life to switch off the power supply or leave it on while using the macbook?
Yes, and the pilot light on the MagSafe2 connector changes from orange to green. If you unplug, you will start draining the battery again, whereas if plugged the Mac will take power from the brick and leave the battery in a charged state.
-
My macbook pro doesn't turn on. The battery is charged but the screen stays black when I press the power button. Anybody has a solution for me please?
Try a #1 SMC Reset and see the Apple links, if that doesn't work make a appointment for a evaluation.
..Step by Step to fix your Mac -
My MacBook Pro is not switching on and my charging light is very dim green
Hey ! My MacBook Pro is not switching on. I was trying to charge my iPhone through the lead attached to the MacBook. I suppose the iPhone charging lead might not be a original. Hence it kept saying that this accessory will not work. So I took it out. As soon as I did that my mac switched off and it would not switch on again. The charger light went really dim green. It usable is more brighter. I've waited for a while. It's not switching on. I was trying to do smc reset but I suppose if I'm doing it right it's not working. I was reading online and I didn't find much help. I live in Pakistan so I can't go to apple store. Please tell me a solution !!?
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own". -
My MacBook pro won't turn on it just gets 2 the spinning wheel and keeps spinning
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
If this doesn't work then you will need to erase the drive and install Snow Leopard from scratch:
Erase and Install Snow Leopard
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. When completed quit DU and complete the Snow Leopard installation. -
MacBook Pro won't turn on and won't charge
My MacBook Pro will not turn on and it appears to not charge. my charger blinks a orange light when I plug it in but the light is very dim. any suggestions?
Bring it to an authorized service center and have them try one of their chargers on it. If the charger doesn't work, then have the battery replaced. If the battery being replaced doesn't charge, replace the power supply.
-
Macbook Pro won't turn on and no charge?f
Hey, I bought my mbp around September of 2009. Last night I put it to sleep, and when I woke up it wouldn't turn on. The battery indicator shows only 1 green light and flashes for a couple of seconds. When I plug in my charger, there is no light, as well. What should I do?
Thanks in advance!Hi Ezam
It's interesting that you say that it's a new battery charger, do you still have the old one and have you tried that?
It sounds like a problem I had with one of the Laptops where I work. We were experiencing problems with the charger so we bought a new one, didn't think anything of it and the Apple Store didn't ask any questions - why would they.
After a few weeks the Laptop seemed to be losing it's charge, so we called in our support contract, turned out that the Adapters are very slightly different and the one we had although it worked was not quite the right one for the Laptop we had (This was one of the older style chargers with the jack type connection).
Not sure if this rule still applies with the MagSafe but might be worth looking into, sounds like the chargers not getting the power there. The 1 battery light you're experiencing is the sign that the Battery doesn't even have enough juice to light one light.
The service Battery warning seems to be a common one coming up at the moment with Snow Leopard but it shouldn't stop the machine from turning on, especially as you can run the MacBook without a battery in (not advisable mind). -
Macbook Pro Shuts down when running off the battery...
Im have the late Macbook Pro 15" and I have had it for a year now. When im running my macbook off the battery it shuts down... I have no clue why. It started doing this about 4 or 5 days ago. I have my battery info here.
Battery Information:
Model Information:
Serial Number: Sony-ASMB012-3916-d74e
Manufacturer: Sony
Device name: ASMB012
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0110
Hardware Revision: 0500
Cell Revision: 0303
Charge Information:
Charge remaining (mAh): 2828
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 2914
Health Information:
Cycle count: 65
Condition: Check Battery
Battery Installed: Yes
Amperage (mA): -544
Voltage (mV): 12137
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 20
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: No
I noticed that the Full Charge Capacity is not that high compared to other macbooks. Could this be the reason why its shutting its self off? Also i copied this info while i was plugged into the AC adaptor. It also says that its fully charged but the percentage on my macbook reads 97%...
I also installed 4GB ram in it 4 months ago and never had this problem. Could having the new ram in it be draining the battery?
If someone could help me with this extremely annoying problem it would really be appreciated. Thank you for your time.I am having the same problem. I just recently noticed that my battery life was less than an hour. In the beginning, I was able to watch 3-4 complete movies while on a flight. Now, it shuts down if on batteries within 10 minutes while the Bar shows 59 minutes.
Here is my System Profiler
Battery Information:
Model Information:
Serial Number: Sony-ASMB012-3887-4d
Manufacturer: Sony
Device name: ASMB012
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0110
Hardware Revision: 0500
Cell Revision: 0303
Charge Information:
Charge remaining (mAh): 1809
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 2074
Health Information:
Cycle count: 57
Condition: Check Battery
Battery Installed: Yes
Amperage (mA): 121
Voltage (mV): 12275
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 20
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: Yes
As you can see, I have only 57 cycles on this battery. I cannot do anything on battery power only anymore. I spent all morning draining the battery to 0 (all lights on battery off) When the battery is charged and when on battery power, the computer will shut off. The battery charge indicator LEDs on the battery itself has 4 of 5 solid and 5th one blinking. The computer will not power on for about 5 minutes when on battery power only. I bought this MBP about 15 months ago. Any help would be appreciated -
My mac book pro is working, but my power light is off, the battery power light is not on and my battery power symbol is a black x. My computer is making a whirring sound sort of like it does when loading a CD. I had a hard time getting the computer to turn on, used the command, option, P and R buttons to turn in on. I have tried restart, but I still get the whirring sound. What is wrong and what do I do?
Didn't do an SMC reset. But in attempting to find out about what that was I found some things to try first. Also, when I went to system preferences - hardware, I couldn't find anything regarding power and battery info. Finally, I unplugged the computer for several seconds, then shut it down, removed the battery, put the battery back in. Then I turned on the computer, plugged in the power cord. Problem solved- no whirring sound, battery charging light is on.
Thanks for getting me in the right direction. -
I spilled diluted orange juice on my laptop, afterwards I switched it off to let it dry, switched it back on and it worked for about 10 mins then switched off and won't switch on again. The battery indicator on the side is constantly on. Please any advice would be extremely appreciated.
Genius reservation http://www.apple.com/retail/geniusbar/
on-line https://getsupport.apple.com/GetproductgroupList.action
https://www.techrestore.com/mac/
http://www.dttservice.com
http://www.myservice.com/macbookpro.html
http://www.ifixit.com/Device/MacBook_Pro
http://www.PowerbookMedic.com
Maybe you are looking for
-
Problem to update Extension Manager
Problem to update Extension Manager 6.0.7 Errore Code: U44M1P7 MAC OS X 10.8.4 For 4 times I contact via chat the support but someone answer me and tell Please wait while I transfer the chat to the appropriate group. But nobody taka care me of the pr
-
Einbinden von swf. flash gallerie in Catalyst-Folie
Hey Leute. Ich hab da mal ein Problem wie folgt: Also.... Es geht um eine Flash-basierte Hompage: ich habe mit "Wondershare Flash Gallery Factory Deluxe" eine Flash Gallery (h:400py w:600px) erstellt und als .xml exportiert. Jetzt wollte ich die dazu
-
Reverse Mass Payment created from F110
We have generated a payment using F110 but not yet printed the cheques. We would like to reverse and reset the cleared ietms from the payment. Any help would be appreciated. PS. The payment was for 400 records so we cannot do this manually!
-
Error messages while installing CC Flash Builder to desktop. Windows 8
ERROR: DF024: Unable to move file at "J:\adobeTemp\{EB510B48-ACF6-43A0-8214-3DA0D6D0936F}\_1661_98e9c69164ca1bd5cffa44e405d6fb 7e" to "J:\Programs\Adobe\Adobe Cloud\Adobe Flash Builder 4.7 (64 Bit)\eclipse\plugins\com.adobe.flash.compiler_4.7.0.34972
-
Somebody install the cs6 version of master collection, that guy doesn´t work now in the oficce. That´s why I can´t update or install any software. Only that I have is the serial number, somebody could help me, please