My MacBook Pro won't turn on at all

When I power it on it makes it's usual chime but the screen does not respond at all. When I shut the lid, the small light on the front of the base of the laptop flashes to show it is on yet there is still no response! I have tried using the charger but still nothing and there are 5 green lights at the side of my MacBook showing it does have charge. I removed the bottom of the computer but do not have the correct screw to remove the battery, what should I do?

Doesn't sound like a battery problem so I am not sure the advantage of removing the bottom?
Force quite the computer by holding the power button for 10 sec+
Reset both the
SMC   http://support.apple.com/kb/ht3964
NVRAM     http://support.apple.com/kb/ht1379
restart

Similar Messages

  • MacBook Pro won't turn on at all.

    I have a 13" MacBook Pro Retina (Late 2012) running OS X Yosemite beta 3 that won't turn on at all.
    I imported a  few pictures from an SD card to iPhoto and then closed the lid when it finished.
    A few hours later, I opened the lid and the screen didn't turn on.
    It's been like this for almost a week now (6 days).
    Pressing the power button doesn't do anything and I've tried resetting the SMC but it still doesn't turn on.
    I also know that it's not a display issue because the CAPS lock doesn't light up.
    Also, when I charge it, the charger becomes green, then orange. But I've charged it for more than 8 hours on the orange light, but still doesn't turn green.
    Please help, I'm on holiday and there are no Apple Stores here

    Some liquid has just spilled into your Mac. What should you do?
    Do
    Immediately shut down the computer and unplug the power cord.
    Remove the computer's battery if it's a portable Mac.
    Disconnect any peripherals (printers, iPods, scanners, cameras, etc.)
    Lay the computer upside down on paper towels to get as much liquid as possible to drip out.
    Note what was spilled on your Mac.
    Bring the computer into Apple store or AASP as soon as possible.
    Don't
    Don't try to turn it back on. Liquids can help electrical current move about the components of your Mac in destructive ways.
    Don't shake the computer (this will only spread the liquid around).
    Don't use a hair dryer on it (even at a low setting a hair dryer will damage sensitive components).

  • My MacBook Pro won't turn on, only a white screen with spinning circle, I've only had it a few weeks! Any ideas what is going on?

    My MacBook Pro won't turn on, only a white screen with spinning circle, I've only had it a few weeks! Any ideas what is going on?

    Mac OS X: Gray screen appears during startup 

  • My MacBook pro won't turn on all the way gets to the apple with the spinning wheel underneath and that's all I need help asap

    My MacBook pro won't turn on it just gets 2 the spinning wheel and keeps spinning

    Reinstall OS X without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
    If this doesn't work then you will need to erase the drive and install Snow Leopard from scratch:
    Erase and Install Snow Leopard
    1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button.  When the menu bar appears select Disk Utility from the Utilities menu.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
    4. When completed quit DU and complete the Snow Leopard installation.

  • My MacBook Pro won't turn on although the battery life is showing full

    My MacBook Pro won't turn on although my battery life is showing full ,

    Go step by step and test.
    http://support.apple.com/kb/TS1365
    Note: Steps 5 and 6
    Step 5
    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".

  • My MacBook Pro won't turn on. What keys do I use toed last week.

    My MacBook Pro won't turn on. What are the keys to reboot?  This happened last week.

    http://support.apple.com/kb/HT3964 if you haven't replaced the PRAM battery in the last 4 years.
    If you have:
    http://support.apple.com/kb/HT1379
    Note, the PRAM battery is not the normal replaceable battery for power.  It is the equivalent of the PC CMOS battery.

  • My MacBook Pro won't turn on, what's wrong?

    My MacBook Pro won't turn on. What's wrong?

    gobetty wrote:
    My MacBook Pro won't turn on. What's wrong?
    Depends upon what you mean by it not turning on, there are various causes.
    Is the power button pressed and nothing happens? Disconnect all other devices, then a SMC and NVRAM reset.
    Is there a white screen and nearly nothing? A hosed EFI firmware.
    Is there a grey screen and a loading bar that gets stuck? Either a failed firmware update or corrupted drive/OS X.
    Is there a grey screen with a spinning wheel? Bad third party or Apple at boot kext file.
    Are you loading but not able to log in? Possible corrupt third party software designed to startup upon login.
    ..Step by Step to fix your Mac

  • My macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?

    my macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?

    Might be a problem with the adapter.
    Help here >  Apple Portables: Troubleshooting MagSafe adapters

  • My macbook pro won't turn on without any reason?

    my macbook pro won't turn on without any reason, is there any solution in this case?

    You need to hit the "reply" button on post to whom your responding too, it's hard to tell if your responding to me or someone else.
    small button on the side of the computer and didn't lightting up( no reponse at all). is their any problems do think with the battery?
    Usually if your battery is dead because it wasn't charged you can do the SMC Reset and then check the Magsafe if it's connected and showing the orange light, then let the battery charge up.
    Once the battery charges up, the computer will boot normally and then you have to reset the PRAM, time, date etc.
    https://support.apple.com/kb/TS1365
    Magsafe issues: https://support.apple.com/kb/TS1713   https://support.apple.com/kb/TS4127
    *PRAM Reset  http://docs.info.apple.com/article.html?path=Mac/10.6/en/26871.html
    What's store in PRAM   https://support.apple.com/kb/HT1242
    Hardware Test
    https://support.apple.com/kb/ht1509

  • I have 12,000 photos on iphoto and my macbook pro won't turn on...gray screen goes to blue screen and that is it...HELP

    I have 12,000 photos on iphoto and my macbook pro won't turn on...gray screen turns blue and that is it.  HELP!!

    Run through this list of fixes
    Step by Step to fix your Mac
    You can do this to copy and remove files from the non booting internal
    Create a data recovery/undelete external boot drive

  • My macbook pro won't turn on. it just stays stuck on a white screen with a little circle spinning around and around when you power it on.

    my macbook pro won't turn on. it just stays stuck on a white screen with a little circle spinning around and around when you power it on. i don't know how to get it to progress past this loading page.

    Resetting your Mac's PRAM and NVRAM
    Intel-based Macs: Resetting the System Management Controller (SMC)
    Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
    Reinstalling Mavericks, Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion, Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    If you are not using Lion, Mountain Lion, or Mavericks then use the following procedure:
    Resetting your Mac's PRAM and NVRAM
    Intel-based Macs: Resetting the System Management Controller (SMC)
    Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
    Reinstall OS X without erasing the drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

  • My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

    My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

    Yes if your model MBP has a removable battery.  If it does not: 
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer. 
    Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
    http://support.apple.com/kb/HT3964

  • My Macbook Pro won't start up. All I get is a grey screen showing a grey folder bearing a question mark. Help please!

    My Macbook Pro won't start up. All I get is a grey screen showing a grey folder bearing a question mark. Help please!

    The folder with the question mark indicates that the machine is unable to find a bootable volume on startup. This is typically caused by one of three things:
    1.) The internal HD has failed or is failing and needs to be replaced
    2.) There is significant directory damage to the volume that requires repairing in order to boot
    3.) Some other internal component failure between the HD and logic board
    I'd ranked them in the order that is most common (from my personal experience). Boot to the OS X Recovery tool and attempt to repair the startup volume. If that fails or the drive is not detected it's usually a tell tale sign of a failed HD.

  • MacBook Pro WON'T TURN ON. Please help!

    I'm an editor and rely on my computer daily. Please help me.
    I purchased my 17" MacBook Pro back in April of 2008. It was dropped once the first year I had it, with no noticeable damage (thank God). I've had no major issues with it, until today.
    I was editing on it earlier this afternoon, and when I was finished, I put it away in my incase backpack like I always do. Put it in my trunk, went on some errands, and just returned home.
    I took it out to power it up. I hear the internal start up sound of the hard drive waking up and trying to spin (no apple sound) and then it just dies. Black screen the whole time. No logo. Nothing. The white light on the button to open the screen turns on and flashes, and then goes off too.
    I'm really freaked out that it's dead. If I can't start it up at all, is there any way to retrieve my files from it? I have some things backed up, but there's a lot of stuff I still need off of it. My main priority in all of this is just making sure I can save my files.
    If this clues anyone in as to what's wrong, a couple of days ago the screen started twitching black for about 2 minutes intermittently. I'd never seen it do that before, and it stopped shortly afterwards. Is this just my computer being three years old and pooping out on me randomly?
    Please help. I'm freaking out. I need all of my software.
    Thanks!

    I just logged in and the software did not return me to this page. How Primitive. It's Sunday for me, the launch day for my new international business. My Skype meeting was to be held on my Macbook Pro. The Apple staff have all decided that this day isn't very important for them, so they're at the beach. My Macbook did not turn on all day, even with the SXX reset or whatever you call it. Ctrl Alt Shift Power. I heard a little click each time I did this, to no avail. In desperation, I turned the 'laptop' (that's what the REAL world calls them) over and saw weird screws for a rare type of screwdriver. I pressed down slightly on the metal casing and heard a few of the clicks like with the SMC reset. I wondered if that would make a difference.
    I turned my computer over, opened it up, pressed the power button and it worked immediately. THE INTERIOR OF THE 2011 MACBOOK PRO MAY BE SHODDILY ASSEMBLED. My battery life is 4.5 hrs max at 50% brightness in safe mode with no 'programs' (not f***ing 'Apps') running. When I browse the internet at 50% brightness in normal mode, the battery lasts 90 mins, although I have never pressed the metal casing on the back of this laptop gently to reassemble the inner workings of this machine before, so it could last for 100 hours. Nope, I'm down to 87% after ten minutes. It's back to normal.
    Summary: To fix your Mac, hit it with a hammer. Hopefully it'll break so you can go back to Windows and actually see how many Firefox windows you have open and right click on things to bring up the menu instead of aiming your mouse for every tiny thing onto pinheads like a frekkin surgeon.

  • Help - MacBook Pro won't turn on

    Help - my macbook pro will not turn on even though it is plugged in. Holding down the power button is ineffective. The power cord has the green "charged" light, but when I plugged it in, it wasn't charged and never did charge (the light never was orange). The computer worked perfectly this morning.

    Will it not turn on at all or do you just get a gray screen?
    If a gray screen, look at this:
    https://discussions.apple.com/docs/DOC-5282
    If it does not turn on at all, try a SMC reset:
    http://support.apple.com/kb/ht3964
    If the reset fails to bring life to the MBP, make an appointment at an Apple store genius bar for a free evaluation.
    Ciao.

Maybe you are looking for

  • How to print specific pages of a pdf from a vb 2013 program using a print dialog

    Hi.  I am using the acrobat sdk to display pdfs from within a vb 2013 program, because the pdfs are large and we have developed indexes on certain columns.  The indexes are stored in SQL tables.  My program has a search window which allows the user t

  • Custom Application in CRM 5.0 SP13

    We have made changes as per note 1017761 to get a custom application working ... In the attached file I have made a summary of the errors related to the "sap.com/home~syn_crm" application. Overall we have 3 missing references to classes or classes de

  • Exporting all settings for Outlook Desktop so that they can be imported into Outlook

    Hi there, I was wondering whether all settings for Outlook Desktop can be exported so that they can be imported into Outlook i.e. .psts, .osts, .pabs, .oabs, .dats, .xmls, .nk2s, .rwzs, .rtfs, .txts, .htms, .dics, .ofts, .srss and .msgs. My Managing

  • Attachment documents

    Hi all, I want to changed the functionality of Add button In the tab Attachment Documents in application crmd_bus2000111(opportunity), i want don't display the Search button and its associated field, but the others fields  must remain. Can someone do

  • Since I work with a backup-projectfile, premiere stops working reporting a 'debug event'

    Hello, Can somebody tell me what the next dubug event means and what to do about it... 'Premiere elements has encountered an error. C:\PRE12\mail\MediaCore\audiorender\API\inc\audiobuffer/audioSubBuffer.I' Because premiere stopped working a sudden mo