My Macbook Pro won't turn on properly. It was perfectly fine when it went into sleep mode earlier on today, please help?
Closed the lid earlier on today and my macbook pro went into sleep mode. about 12 hours later i opened it and the battery was dead. Plugged the battery charger in and pressed the power button. It boots up, disc drive works and it sounds the same as it would working perfectly fine. Keyboard works and there is noise coming from the laptop when i press certain buttons like the volume etc but the screen isnt working. Unable to enter FireWire targert disc mode to fix the sleep mode files which is what i think is wrong with it but i don't have a FireWire and i don't really want to be playing around with my macbook's internal files incase i accidentally touched the wrong thing. Does anyone know what could be wrong? Should i just take it to get repaired and let a specialist repair it? Anything i should know about/be doing/not doing?
Plug it into a power oulet & then reset your SMC:
http://support.apple.com/kb/HT3964
Similar Messages
-
MacBook Pro won't turn on properly.
It beeps three times repeatedly and continues until shut down. Restart and it just beeps again. Running Mountain Lion (10.8). Screen doesn't light up. Was working fine last night. Fully charged. This has continued since I tried to start up today.
Tried resetting SMC. No change.Ram problem. Have you changed ram modules?
-
My MacBook Pro won't turn on, only a white screen with spinning circle, I've only had it a few weeks! Any ideas what is going on?
Mac OS X: Gray screen appears during startup
-
My MacBook pro won't turn on it just gets 2 the spinning wheel and keeps spinning
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
If this doesn't work then you will need to erase the drive and install Snow Leopard from scratch:
Erase and Install Snow Leopard
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. When completed quit DU and complete the Snow Leopard installation. -
My MacBook Pro won't turn on although the battery life is showing full
My MacBook Pro won't turn on although my battery life is showing full ,
Go step by step and test.
http://support.apple.com/kb/TS1365
Note: Steps 5 and 6
Step 5
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own". -
My MacBook Pro won't turn on. What keys do I use toed last week.
My MacBook Pro won't turn on. What are the keys to reboot? This happened last week.
http://support.apple.com/kb/HT3964 if you haven't replaced the PRAM battery in the last 4 years.
If you have:
http://support.apple.com/kb/HT1379
Note, the PRAM battery is not the normal replaceable battery for power. It is the equivalent of the PC CMOS battery. -
My MacBook Pro won't turn on, what's wrong?
My MacBook Pro won't turn on. What's wrong?
gobetty wrote:
My MacBook Pro won't turn on. What's wrong?
Depends upon what you mean by it not turning on, there are various causes.
Is the power button pressed and nothing happens? Disconnect all other devices, then a SMC and NVRAM reset.
Is there a white screen and nearly nothing? A hosed EFI firmware.
Is there a grey screen and a loading bar that gets stuck? Either a failed firmware update or corrupted drive/OS X.
Is there a grey screen with a spinning wheel? Bad third party or Apple at boot kext file.
Are you loading but not able to log in? Possible corrupt third party software designed to startup upon login.
..Step by Step to fix your Mac -
my macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?
Might be a problem with the adapter.
Help here > Apple Portables: Troubleshooting MagSafe adapters -
My macbook pro won't turn on without any reason?
my macbook pro won't turn on without any reason, is there any solution in this case?
You need to hit the "reply" button on post to whom your responding too, it's hard to tell if your responding to me or someone else.
small button on the side of the computer and didn't lightting up( no reponse at all). is their any problems do think with the battery?
Usually if your battery is dead because it wasn't charged you can do the SMC Reset and then check the Magsafe if it's connected and showing the orange light, then let the battery charge up.
Once the battery charges up, the computer will boot normally and then you have to reset the PRAM, time, date etc.
https://support.apple.com/kb/TS1365
Magsafe issues: https://support.apple.com/kb/TS1713 https://support.apple.com/kb/TS4127
*PRAM Reset http://docs.info.apple.com/article.html?path=Mac/10.6/en/26871.html
What's store in PRAM https://support.apple.com/kb/HT1242
Hardware Test
https://support.apple.com/kb/ht1509 -
I have 12,000 photos on iphoto and my macbook pro won't turn on...gray screen turns blue and that is it. HELP!!
Run through this list of fixes
Step by Step to fix your Mac
You can do this to copy and remove files from the non booting internal
Create a data recovery/undelete external boot drive -
my macbook pro won't turn on. it just stays stuck on a white screen with a little circle spinning around and around when you power it on. i don't know how to get it to progress past this loading page.
Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstalling Mavericks, Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion, Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
If you are not using Lion, Mountain Lion, or Mavericks then use the following procedure:
Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1. -
TS1365 My macbook pro won't turn on
My macbook pro will not turn on. It was working normally and then I left for about half-an-hour to eat dinner. When I got back and pressed the power button (because I thought it'd just gone to sleep) nothing happens. I've tried pushing to power button a bunch of times but it doesn't do anything. I can hear the computer running though. It's also fully charged. I dont' know what's wrong with it.
according to the article
"If you are still unable to start up your computer after trying each of these steps, schedule a service appointment with an Apple Retail Store or an Apple Authorized Service Provider. If you plan to visit an Apple Retail store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only)." -
MacBook Pro won't stay asleep with external monitor attached. When sleep is selected from the Apple menu the computer will go to sleep only to continually wake up...go back to sleep...wake up...etc. every few seconds. This only happens when using the external monitor. Does anyone have any suggestions?
Mine does that too. The worst thing is when it goes to sleep, then wakes up and keeps running while the lid is closed and it is wrapped up in a case. I am afraid when the hot weather comes it is going to burn up. I am hoping Apple fixes it in the software or they may have a melted MBP to replace.
Then when I open the lid it is crashed running at fill tilt, pumping out heat to beat the band. I am forced to hold the button down and reboot.
I wiped my hard disk and reinstalled my OS, but it didn't help. I reversed my OS to 10.5.0 and it solved the DVI problem but still won't sleep. This post will probably be deleted by Apple, they did it a few days ago. I just don't know what to do, and I consider myself a real Apple expert. Just hoping you realize you are not the only one. -
My MacBook Pro won't start it just goes beep beep beep when I press the power button
My MacBook Pro won't start it just goes beep beep beep when I press the power button
Hi Csound1,
I haven't added any RAM my daughter was using the computer then it hung so powered it down then the beeping started. Do you know if there is a combination of buttons I can press when powering up that will put me in some kind of safe mode so that I can find out what's up, I tried pressing D when the beeping started but it didn't make a difference.
MC -
Help me! I have a new iPad mini that won't turn on. It was working fine this morning then i turn it off and it never turns back on. it doesnt register with iTunes and resetting isnt working either. All I did is download instagram and snapchat and poof doesnt work. I have had these apps before!
Make sure it's plugged into the charger.
Frozen or unresponsive iPad
Resolve these most common issues:
• Display remains black or blank
• Touch screen not responding
• Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Home button not working or unresponsive, fix
http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
Fixing an iPad Home Button
http://tinyurl.com/om6rd6u
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Cheers, Tom
Maybe you are looking for
-
Java System Application Server create-agent-problem
When i try asaadmin> create-node-agent it says CLI147 Invalid command, create-node-agent I don't know why, that command commonly used on all the documentation I've found. Anybody knows why could it be?
-
How do i put more than 1 photo on an 8x10 sheet of photo paper so i can print 3 or 4 at a time?
how do i put more than 1 photo on an 8x10 sheet so i dont waste photo paper???
-
Convertion from Bex Reports to Crystal reports
Hi all we are integrating BI with BO, i have a task to convert all existing BEx reports into Crystal Reports. I knew nothing how to do this, can any one please explain in detail steps how to convert BEx reports into crystal reports. For example any d
-
Where is the best place to get/read information on the pros and cons of updating my OS from Snow Leopard to the current OS? I have an iMac 27" intel, purchased Nov 2009. I am currently using 10.6.8
-
Broadband Talk handset numbering on Home Hub 2B
Upgraded recently from an old Home Hub 1 to a 2B version. Initially, I made a bit of a mess in registering the two former handsets used for BBTalk access and as an internal intercom. Therefore I used the De-register all handsets option from the Hub