My Macbook Retina doesn't log back in from sleep after typing in the password, have to force shut down

Hi all,
Recently i've been having this problem once in a while (once every few days) that when I opened up my computer from sleep, I typed in my password and clicked enter. After that, it shows that normal grey box thing; normally it logs in after a few seconds, but sometimes i wait for 2 minutes and still it doesn't log in. I sleep it and wake it again, but this time i type the password and i click enter, but nothing happens, i can't click switch user either. At this point my only choice is to force shut down my macbook. This problem is a bit annoying since sometimes i have unsaved work.
Thanks in advance for any reply/ies.

Press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly to restart.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Similar Messages

Issues logging back in from sleep

Hi, I have a Macbook running Leopard (upgraded from a previous Tiger installation) 10.5.5. Sometimes when I log back in from sleep mode, the screen flickers and the log in box disappears. To get it to reappear so I can log back in, I have to close and open the Macbook again. Sometimes when the log in box disappears, the Macbook stops making any sound whatsoever. Yesterday, the Macbook screen suddenly went black and the hard drive made the usual "waking up from sleep" grinding noises several times in a row. I closed it and after a while, it stopped grinding and rebooted. Any ideas?

Hello,
Try resetting the System Management Controller
Carolyn

My Mail app opens unprompted everytime i reboot or awake my macbook pro from sleep. This was not an issue until i shut down my laptop for the first time in a while 2 days ago. ANy ideas how to stop this?

I recently shut down my MacBook Pro for the first time in a long time. SInce then, everytime i reboot or awake my laptop from sleep, the Mail app opens unprompted causing my computer to slow down incredibly, and some apps to freeze. I have no idea how to stop this or why it even started doing this. Any ideas on how to get it to stop? Thanks!

I have this problem too with my Macbook Air. Mail opens automatically every time my laptop sleeps. I actually just asked about this in my own thread. However, it is not causing my apps to freeze.

HT204266 Help...bought an iPad for mum at Xmas, got set up with App Store account and bought scrabble but since then we cannot log back into buy anything it asks for the password which we give it accepts but it asks us to answer security questions that go

Trying to login to the App Store and it keeps asking me to answer security questions but when I try to do so the page just goes blank to white and then disappear . By this point I am already successfully logged in.
Please help.

Rescue email address and how to reset Apple id sec. questions.
http://support.apple.com/kb/HT5312?viewlocale=en_US&locale=en_US
If that doesn't work and your verify the following info, call 1-800-APL-CARE.
1. apple id username, that is not locked or disabled.
2. serial number of an apple product registerd in your name
3. Billing info associated with your account

HT201177 My new MacBook Retina cannot play any videos on any browser. This includes the Apple videos. It keeps saying Missing Plug-In. I am not sure what I am supposed to do. Can someone please help me out?

My new MacBook Retina cannot play any videos on any browser. This includes the Apple videos. It keeps saying Missing Plug-In. I am not sure what I am supposed to do. Can someone please help me out?

My iPod mini, 4gb is hard to get serviced obviously because they dont make them anymore
It is as simple to get it serviced as the day you purchased it.
How is it hard to get it serviced?
How long have you had your iPod?
i get maybe 4-5 hours of battery life, maybe even 6 if im lucky
That is not good but it's not "terrible".
If you've had it less than a year, send it back to Apple to replace the battery.
thought that i might buy an attachment type accesorie that i plug into the usb port on my ipod
It's called a dock connector, not a USB port.
i found a product in the online store, that i guess you place the ipod mini on, and it gives you up to 20 or so more hours of time but then it says that you have to have a firewire port or cable?
What is it? The firewire port is on the computer, not the iPod.
If the original battery is going bad, the first thing to do is get that sorted out.

My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!

My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

I changed my name on MacBook pro, I could not log in after that though the password is unchanged but tHe name appeared on the login window is the original name?..how I can log in?

I changed my name on MacBook pro, I could not log in after that though the password is unchanged but tHe name appeared on the login window is the original name?..how I can log in?

Hmmm. Maybe try this?
OS X: Changing or resetting an account password

Hi, i hv macbook mid 2010 ..it was working fine till few days back but after updating it to mavericks, it keeps on shutting down itself...what to do ? could sm1 help me out ?

hi, i hv macbook mid 2010 ..it was working fine till few days back but after updating it to mavericks, it keeps on shutting down itself...what to do ? could sm1 help me out ?

The startup disk may need repairing...
Startup your Mac while holding down the Command + R keys.
From there you should be able to access the built in utilities in OS X Recovery

I recently bought the 27" IMac. I have to force shut it down, the menu shut down doesn't work, and most of the time it will start back up on it's own several hours or even days later. Any ideas?

I recently bought the 27" IMac. I have to force shut it down, the menu shut down doesn't work, and most of the time it will start back up on it's own several hours or even days later. Any ideas?

Note: No iMac PPC is 27". PPC is for the iMacs that were new until the beginning of 2006. They are all Intel now.
I've requested a moderator move your thread. No action is needed on your part.

I have frequent instances of my Macbook Pro beeping 3 times and then I have to forcefully shut it down by pressing the power button. What is this all about? Please help. Thank you.

I have frequent instances of my Macbook Pro beeping 3 times and then I have to forcefully shut it down by pressing the power button. What is this all about? Please help. Thank you.
I saw this report being sent to Apple:
Interval Since Last Panic Report: 581719 sec
Panics Since Last Report: 10
Anonymous UUID: F4CF708D-D85C-4EC5-8047-4FC22C6B03AF
Fri Mar 7 13:00:14 2014
panic(cpu 0 caller 0xffffff80002d1208): Kernel trap at 0xffffff800020c590, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000000000, CR3: 0x0000000007541000, CR4: 0x0000000000040660
RAX: 0xffffff8000000000, RBX: 0xffffff800d35a870, RCX: 0xffffff800cf55cd8, RDX: 0xffffff80008a8fcc
RSP: 0xffffff805e5f3d60, RBP: 0xffffff805e5f3da0, RSI: 0x000000001dcd6500, RDI: 0xffffff800d168778
R8: 0x0000000000000001, R9: 0xffffff805e5f3e88, R10: 0x0000000000000011, R11: 0x0000000000000000
R12: 0x0000000000000000, R13: 0xffffff800d168770, R14: 0xffffff800d168778, R15: 0x0000000000000000
RFL: 0x0000000000010082, RIP: 0xffffff800020c590, CS: 0x0000000000000008, SS: 0x0000000000000010
Error code: 0x0000000000000000
Backtrace (CPU 0), Frame : Return Address
0xffffff805e5f3a00 : 0xffffff8000204d15
0xffffff805e5f3b00 : 0xffffff80002d1208
0xffffff805e5f3c50 :
Model: MacBookPro8,1, BootROM MBP81.0047.B27, 2 processors, Intel Core i5, 2.3 GHz, 4 GB, SMC 1.68f99
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 384 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 5.100.198.104.5)
Bluetooth: Version 2.4.5f3, 2 service, 12 devices, 1 incoming serial ports
Serial ATA Device: Hitachi HTS545032B9A302, 298.09 GB
Serial ATA Device: OPTIARC DVD RW AD-5970H
USB Device: FaceTime HD Camera (Built-in), 0x05ac (Apple Inc.), 0x8509, 0xfa200000 / 3
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfa100000 / 2
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 5
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x821a, 0xfa113000 / 8
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0245, 0xfa120000 / 4
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfd100000 / 2
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd110000 / 3

Hmm. The problem still may be the RAM - Apple buys the RAM it puts in its machines from third-party vendors (usually Hynix) so it could be a RAM problem.
There are a couple of things that you can do yourself before taking your machine into an Apple Store or an AASP... download and run an application named Rember that will run a RAM test for you - let it run for a couple of hours or even overnight. If it turns out that your RAM is faulty, Rember will let you know. If it is faulty, then you have a couple of options - replace the RAM yourself or (particularly if you're under warranty still) take the machine to an Apple Store or AASP and have them replace the RAM.
If Rember finds no fault with the RAM, then you'll need to take it into an Apple Store/AASP and get a free diagnosis on the machine. Three beeps do usually indicate faulty RAM, but if it tests good with Rember you likely have another problem - it could be something as simple as the RAM, somehow, not seated correctly or signs of another hardware problem.
Run Rember first... call back with results.
Good luck,
Clinton

Mid 2009 17" MacBook Pro battery shutdown issue when waking from sleep.

My unibody 17" MacBook Pro occasionally shuts down on waking from sleep when it isn't plugged in.
When I open the lid to wake it I can hear the hard drive and fans starting to spool, and then the next second it's off and silent. The laptop doesn't mind being turned on again after it does this and might go a week without doing it again, equally it might do it next time I try and wake it from sleep. It does this regardless of battery charge level.
coconutBattery says the battery still has 86% of its designed capacity, and I haven't noticed anything else untoward regarding battery charging or performance when in use.
So my question is two fold:
1) Does it sound like the battery's internal processor is malfunctioning, or could it be something else?
2) If it is the battery's internal processor, will replacing the battery replace the processor, or are they fitted separately (in defference to the 'internal' part of its name)?
Cheers,
James
nb. just in case it makes any difference, the laptop is a 17" Mid-2009 MacBook Pro, 2.8GHz Core 2 Duo with 4Gb Ram running OSX 10.7.3

James
I have had issues when i press the space bar from sleep, sometimes it wakes but others i'm forced to power it on with the power button.
Is this similar to anything you've experianced?
Its so inconsistantly these days, but i'm also connected to an external screen.

Brand new 13" rMBP (mid-2014) doesn't wake from sleep after a few hours

Hi,
I have brand new, mostly untouched, 13" rMBP running Mavericks (10.9.4) that crashes during sleep. If I close the lid and leave it for more than a few hours, I have to do a force shut down by holding the power button for a few seconds and turn it back on again.
I've already followed the advice of this article: OS X: When your Mac doesn't sleep or wake and have called Apple Support, who did nothing but read the article to me.
I have:
- reset the System Management Controller
- restored all defaults in Energy Saver preferences
- booted into Safe Mode to verify disk (unsure of whether or not this was effective at all)
In my Console, I am getting a line that says "com.apple.message.signature: Platform Failure"
According to this other thread - MB can't wake up from sleep anymore - it seems like it might be a hardware failure. Can anyone confirm this and/or advise on possible next steps?
Thanks.

If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies.

How can i stay logged in on iPhone Skype after i delete the app from the 'current' apps?

How can i stay logged in on iPhone Skype after i delete the app from the 'current' apps?
Thanks for ur answers !

You are correct. There is no other way to recover this material, and yes it would have been a good idea to backup the iPhone prior to the restore. Remember that a restore to a previous date deletes everything on the device and puts it back to the state of things on the date you choose. The texts and contacts would be gone. Did you possibly sync the contacts with a supported application on the computer? That is the only other way to recover contacts. They are designed to be synced with a supported application on the computer, or with a cloud service such as iCloud, Google or Yahoo.

I cant force quiet or relaunch the finder. it says"not responding". Although other apps are running just fine. I've tried restart several times/force shut down several time. I am using a mac book pro retina, Mavericks 10.9.5.Nothing works. Any idea??

How do i quiet finder?i can't force quiet or relaunch finder. it says' "finder not responding". Therefore I couldn't shut down. I've tried to force shut down & restart several times. but still finder won't quiet. Any idea please???? I am using a macbook pro retina with Mavericks 10.9.5.

Go to Finder and select your user/home folder. With that Finder window as the front window, either select Finder/View/Show View options or go command - J. When the View options opens, check ’Show Library Folder’. That should make your user library folder visible in your user/home folder. Select Library. Then go to Preferences/
com.apple.finder.plist. Move the .plist to your desktop.
Re-launch Finder by restarting and test. If it works okay, delete the plist from the desktop.
If the same, return the .plist to where you got it from, overwriting the newer one.
Thanks to leonie for some information contained in this.

Purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death" any suggestions?

purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death" any suggestions?
My machine was patched to date 10.x.x. I was lucky to get an internet connection and I selected the option to re-download Lion... its curruently being downloaded. What if that doesn't work?
Any thougths would be appreciated.
Joe

And you have a workstation? not a notebook.
Usually a driver or hardware, nothing that Disk utility will fix.
You know of course what a Prohititory Sign is?
prohibitory sign, kernel panic
Forum devoted to Lion:
Mac OS X v10.7 Lion Communities
Tips and FAQs
FAQ kernelpanic
Resolving Kernel Panics
Avoiding eliminating Kernel panics
Lion App Compatibility Table - RoaringApps
RoaringApps Mac OS X Lion Application Compatibility
did you make sure your apps, drivers, and hardware support Lion?

My Macbook Retina doesn't log back in from sleep after typing in the password, have to force shut down

Similar Messages

Maybe you are looking for