My macbook won't boot pass the apple logo and the spinning wheel
Some programs on my Macbook starting crashing so I tried restarting it. Now it doesn't load past the grey screen with the apple logo and the spinning wheel.
I've tried installing the Install disc, holding 'c' but nothing happens.
I've tested the hardware holding 'd' in the start up, in which the test can back clean, so I'm assuming it's a problem with the software.
I've followed almost all the troubleshooting solutions on the apple website including restarting the PRAM and SMC, with no success.
However I foolishly followed a solution that was meant for an earlier version of Mac OS X, which invloved starting up in single-user and entering some commands, this appears to have done nothing but i'm concerned it may have done some extra damage.
I have bootcamp installed and I can boot up windows with no problem and even access some of the files on the Macintosh HD.
My backup harddrive broke recently so I haven't got a back up of any of my files either.
My question is, is there any way of fixing this problem or even just saving all my files and data so I can format the hard drive and start again, other than finding someone with a mac and try using the firewire method?
thank you for your time and help.
There's a possible solution but you must have the proper installer DVD for the computer. Assuming you do:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.
Similar Messages
-
MacBook won't boot - stuck showing the Apple logo and the spinning circle.
Hi.
My MacBook suddenly froze when I was using it today. Displaying the spinning beach ball.
It never came out of it, fan running at max speed, so I tried to force restart it (Control-Command-Power), but that didn't work, so I forced the MacBook off (holding the power button pressed.)
When trying to start the MacBook again it couldn't boot. It kept displaying the grey screen, with the Apple logo and the spinning circle below the Apple logo.
I left the MacBook like this for 10-15 minutes, but nothing happened.
Went on to try the following.:
*- Removed the AC-adapter and battery for 5 minutes.*
*- Command-Option-P-R (Resetting PRAM and NVRAM).*
*- Resetting System Management Controller (SMC).*
*- Command-S (singleuser boot)*
And checking the HDD with sbin/fsck -fy
= "The volume ** appears to be OK."
*- Command-V*
Stops on the following line, and fan ramps up to full speed.:
DNSServiceRegister("ssh.tcp."): -65537)
Force reboot didn't work. Had to force it off.
But, nothing helped.
It simply won't boot.
I also tried to boot Ubuntu 7.10, but it hangs after a short while displaying "Kernel panic".
Force reboot didn't work. Had to force it off.
Also tried the option to boot from the first HDD (in the boot menu on the Ubuntu 7.10 disc), but that didn't work either. Only got a black screen, with a blinking cursor top left, and fan ramping up to max.
Again, force reboot didn't work. Had to force it off.
The only thing that has worked so far is exiting the Ubuntu 7.10 CD boot menu, and pressing enter on the prompt that appears.
But, after rebooting, the MacBook still refuses to boot into Mac OS X.
I left the MacBook alone, hoping it would work its way out of the spinning circle, but after 2 h 38 min nothing had happened.
Does anyone know how to fix this?
:. nattugglanThis happened to me last night.
I was updating my iPod and I got a message saying that it needed to do an update. I installed the update and went on ahead putting new songs on my iPod. When it was finished i ejected as I usually do and closed down.
When I went to check me e-mails this morning the Macbook would not boot. It sticks on the grey screen with the Apple and the spinny disc underneath, then it restarts and sticks on the same screen. The last software to be onstalled was Norton 11 on Monday but I have used the Macbook since. I cannot think why it will not boot.
I am loathed to do a reinstall as I have some things on the Macbook that I had not yet backed up.
Any advice? -
My imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?
my imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?
I have started having trouble since i had to upgrade OS the latest in July 12.http://support.apple.com/kb/TS2570 Follow this article and when it gets to the part where you go into disk utility using your install disc, you'll actually boot up holding down Command and R
-
How do I fix a initializing problem with my macbook pro? I only get to the blank screen with the apple logo and the "processing something" sign... it just doesn't start the system....
Please help
MarceloIf there is no loading bar, it's usually a problem with a third party kext file in OS X itself.
You can press the power button down to force a hardware shutdown, then reboot holding the shift key down on a wired or built in keyboard, this will disable them and you go around and update your third party software.
Gray, Blue or White screen at boot, w/spinner/progress bar
Also take this time to backup your users files off the machine if possible.
Most commonly used backup methods
Sometime that won't work and you need to do more
..Step by Step to fix your Mac -
My macbook pro mid 2012 will not start up. I was running bitdefender and when I went to see if it was done, I had the apple logo and the loading (winding circle) on the screen. I can not get out of this. I used my back up external drive and it did nothing. It did light up.
samnleosgpa,
you may have faulty RAM. Are you able to boot into your MacBook Pro’s Apple Hardware Test (“AHT”)? If so, try running it to see if it can detect a problem. If you’re not able to run its AHT, and you’ve upgraded your MacBook Pro’s RAM before, try reïnstalling its original RAM and see if you can get past the “-6002F” error code. If you aren’t able to run its AHT, and you haven’t upgraded its RAM or you no longer have its original RAM, then I’d recommend that you make an appointment at your nearest Apple store to have them diagnose the problem. -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
On start up of my new iMac it locks on the grey screen with the apple logo and the progress wheel spins. Boot up in safe and this is where it stopped at "BootCacheControl: Unable to open /var/db/bootcache.playlist: 2 no such file or directory. "
Reinstalling MacOS does NOT fix the problem for me. I'm still searching a solution !
Bernard -
Hi, I am not able to reboot my Mac desktop.
When I switch on the Mac, I get a white screen with the Apple logo and the little rotating circle.
The system refuses to boot.
What can I do?
MarcusWe need to get you moved. This forum is for mini-tower Macs built between 1998 and 2005 and doesn;t get as much traffic ("eyeballs on the problem") as the forums for newer Macs.
Please do "About this Mac" from you Apple menu and tell us what that says for "processor" and Mac OS version. Looks like this:
or this for later Mac OS versions:
With that we can figure out which of the two iMac forums you need and get the Hosts to move your post. -
When opening my MBP, all that shows is the apple logo and the forbidden sign
Hello everyone,
So I'm on a 2011 MPB using 10.9.5.
I've closed it after using two nights ago, and when I came back home the day after and tried opening it, all that appeared was an alternation between the apple logo and the forbidden sign (here it is : http://stickeramoi.com/3447-3369-large/autocollant-panneau-interdit-interdiction .jpg)
I've tried repairing the disk but that failed.
Tried also re-installing OS X on it but that took about 17 hours (which is ridiculous) so I've cancelled that and instead, tried restoring a Time Machine save.
After it finished restoring the latest backup, I'm still faced with the same problem. It just won't boot.
Thank you for your time and help,Yeah well I think I've tried about everything that I found out there.
From console commands to installing Lion through Internet recovery...That's it, I give up
Will take it for replacement tomorrow.
Thank you -
Ipod nano 4th generation switches between the Apple logo and the menu
I have a 4th generation 8 g iPod Nano that probably has about 1 hour of use since my wife won it in a raffle over a year ago. When I went to recharge it yesterday, the only thing that happens is that the display, when connected to the computer, flips back and forth between the Apple logo and the menu screen. Whenever either one of them appears, it will disappear in a few seconds, then repeat the sequence. I have done a reset and restore,and installed the latest software version but the same thing happens over and over again. If the iPod is detached from the computer, ie, its power source, NOTHING happens on the display. It black and you can't get it to show anything. My theory was that the battery needed to be replaced even though it wasn't used much in the year since she got it. In fact. the absence of use and recharging it and discharging it may have lead to this problem in the first place. However, my one issue with that theory is that, when connected to a power source, like the computer, I would think I could get it to function normally, which I can't. I was able to get to the "service menu" which won't disappear when I move about different choices, as long as its connected to the computer. Again I can get nothing if its not connected to a power source.. does anyone think that this problem could be solved by replacing the battery or does it seem like that is only part of the problem? Thanks for any help and suggestions you may have to offer.
GeoffDespite the Nano only being used for an hour or so, the battery needed to be replaced= problem solved!!
-
My MacBook Air 11" freezes at startup. Just get Apple logo and a spinning wheel. Help!!
I've drained my MacBook Air's battery but manage to shut down properly. When I restart all I get is the Apple Logo and a spinning gear.
I've tried pressing Option, Command & Esc key but it's not working.
Please help!!I've drained my MacBook Air's battery but manage to shut down properly. When I restart all I get is the Apple Logo and a spinning gear.
I've tried pressing Option, Command & Esc key but it's not working.
Please help!! -
i've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?
Look at this support article:
http://support.apple.com/kb/ts2570
Ciao. -
Just upgraded my iPad to IOS5 and when the download was completed, a window said that there was an error and it could not restore. Now I have a black screen with the Apple logo and the circle lines. None of the buttons respond. Help, please!!
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. Maybe this will let the iPad reboot and then you may need to restore again but see if this helps to start the iPad first.
-
my ipad 2 shut off and now all I get is the apple logo and a spinning circle
Try holding down the home button and the sleep / wake button at the same time to restart the iPad .
-
hi!
can somebody please help me?
i wanted to update my iphone 4s to ios6. no problems until the install/loading bar appeared on the iphone. that was 2 hours ago. nothing happened there is no progress being showed.
i also reset my iphone (home button + standby button). result: the apple logo and the bar appear, but still nothing happens...
thanks for helping!
kr,
clemulusI took my phone to apple they replaced the speaker. That corrected the problem
Maybe you are looking for
-
When trying to authorize my daughtes ipod classic to a new laptop it pops up and asks for apple id but the email is not one of ours and it will not let me change it is there any way to fix this problem Thanks in advance
-
IMovie 09' Export 1080p Only Viewable In 360p
Hi, I am so annoyed right now because of the fact, i've uploaded this video to youtube, and it is only viewable in 360p when I know I exported it to 1080p. I filmed it with my full HD camera, and it was set to full HD when I recorded it, and I export
-
Hi All, Can any one give me list of vendors who provides "SFTP-SSh with /PGP encryption" Adapters? I Googled & search on SDN and found only 4 vendors below, but want to search more vendors. 1) www.advantco.com/?q=node/9 2) www.seeburger.com/fileadmin
-
I downloaded the free adobe app on my iPad. No matter what I do, and I have read these pages for hours, I still can't figure it out. I have no icons anywhere, no matter where I tap on the screen. There must be something I am not doing. What did I do
-
Can anyone help me with retreiving datalog files?
I have been working to find a way to read an analog input signal as a waveform, and then attempting to save the data (as just the raw data--like ordered pairs) to a file. Obviously, I would like to be able to read this data later on, but I have been