My mega 651 wont start

Hi there ,
need a little help
Below is a list of things , i currentley have have in my pc , please could you tell me which will work and which wont , i have just bought a msi mega 651 pc .
Intel celeron D 2.4 GHz 256K charche
256 DDR400
40 gb 7200 chache hard drive
Nec dvd rw
thanks very much ,
Gazz

MY 651 has now dies It didn't work the other day but a reset of the bios and it rebooted i have tried this this time and no joy. No beeps or anything else. The hard drive does not spin up nor does the cpu fan.
I have tried the fan in my other PC and it spins fine, I have also removed all cards and IDE devices no joy. I have left the machine with the CPU and one stick of ram.
Any ideas? I have been leaving the case off so as to keep the machine a bit cooler, so i am hoping it is not the CPU.
Any ideas anyone?

Similar Messages

MEGA 180 WONT START UP, HELP PLEASE.

I have a mega pc 180 and the first problem is the LCD wont work, Tried flashing it with no luck.
The main problem is after its been switched on for about 30 - 60 mins if i shut it down and leave it for about 5 mins it wont switch back on again, then if i leave it and try it the next day it will switch straight on.
The cpu temp is on 35 which is good so dont think it overheating. All i can think of is its a dodgy power supply or maybe the power supply is overheating.
When it wont switch on theres must be some power there as the HIFI led comes on green and i can hear the power go to the cdrom.
Any help would be appreciated, dont really want to package it all back up and send it back.
Cheers

When it won't start up does anything appear on the boot screen ? For instance does it detect video ? Does it detect CPU ? Does it detect memory ? Does it detect disks ? These all output info to the screen while the system is booting and can give a clue as to where the problem is.
Something to try the next time it won't start..... Remove the power plug from the walll...wait 10 seconds... plug it back in and see if that helps. Much easier than waiting 24 hours if it works. I have to do this a couple times a week. Although I have never found a repeatable sequence that causes it to fail. It never the less fails often enough to be a pain. And when it does fail the HIFI works just fine.
Good luck

Things to know before building a Mega 651 (and other things you should know afte

Okay, following hot on the heels of the "things to know" series on Mega 180 and 865, I thought I'd just chip in with this short post on what you should know before splashing out on a nice budget Mega 651
PROCESSOR SUPPORT:
The official list of supported CPUs can be found here:
http://www.msi.com.tw/program/products/slim_pc/slm/pro_slm_cpu_support_detail.php?UID=431&kind=4
Basically the ageing SiS651 chipset does not support Celeron / P4 cpus above 533mhz, and does NOT support the newer "Prescott" core cpus
Celeron > 400Mhz FSB
P4 Northwood > 533mhz FSB (512kb L2 cache)
MEMORY:
Basically to add to what is listed in the 865 "things to know"; from my own experience of using MSI motherboards in the past, ALWAYS use good quality branded memory, as using cheaper "generic" types inevitably leads to major problems. I know for a fact that Crucial, Kingston and Samsung types work well in MSI motherboards, and you should be okay with other high-end brands like Corsair and Geil.
DRIVERS:
DON'T bother using MSI LiveUpdate! The drivers provided on the cd supplied will work, but if you wish to download the latest drivers, you will find them here:
http://download.sis.com/
Download and install the:
Chipset Software > SiS AGP (Gart) Driver
IGP Graphics Drivers > SiS650 and 740 series
http://www.realtek.com.tw/downloads/dlac97-2.aspx?lineid=5&famid=12&series=8&Software=True
for Realtek AC97 Audio drivers
http://www.realtek.com.tw/downloads/downloads1-3.aspx?lineid=1&famid=3&series=16&Software=True
For Realtek Onboard Network interface
The modem drivers supplied on the CD should work, I really don't know much about them as I have never used them (sorry). Failing that, if you are connected to the internet, Windows Update should be able to find them for you.
OPERATING SYSTEM SUPPORT
MSI state that only Windows XP is supported on Mega 651 (and other Mega barebones). Other versions of Windows (98, ME, 2000) will work provided you have drivers for hardware devices, all of which are provided on the install CD or from the links supplied above.
You'll find that earlier versions of Windows won't have the drivers for the built-in card reader, so you may have to do a "google" search to get them. On my Mega 651, they are listed in Device Manager as "OEI-USB" devices.
If you haven't already got Windows XP then I suggest you consider upgrading at the earliest opportunity; Microsoft themselves no longer support Win 98 / ME and most new software is being designed to work only with Windows XP
Please note that MSI do NOT supply or support drivers for Linux; if you wish to attempt to install Linux on a Mega 651 (or other Mega PC model) you will need to obtain drivers yourself. The remote and LCD display functions will also not be available under Linux, unless some clever bod has developed drivers to do so.
MEGA RADIO AND LCD DISPLAY:
Download the Mega LiveUpdate for Mega 651 from here:
http://www.msi.com.tw/program/support/software/swr/spt_swr_detail.php?UID=431&kind=4
This will update your MEGA Radio program, update the BlueBird HIFi module firmware and allow you to set a "greeting" displayed on the LCD display when you switch on HiFi mode. Apart from that the LCD display serves NO other purpose in PC mode.
After updating the firmware, you should power off your Mega 651, unplug the mains power cord for a few seconds then reconnect and restart for changes to take place.
OTHER MSI SOFTWARE:
If you REALLY must try out MSI Media Center III, it does work on the Mega 651, but I don't think the remote will work correctly.
Although PCAlert 4 has been reported to work on the Mega 651 - having read the numerous problems most users have, I don't advise installing it. If you do get it to work correctly, unlike on the Mega 180 and 865, it will not display temps or fan speeds on the LCD display, as this feature only works on the 180 and 865, as they use diferent LCD displays.
EXPANSION CARDS:
Same as with other Megas, you get 1 AGP and 1 PCI slot.
The AGP slot only supports up to 4x cards; a faster card will work, but only at 4x.
Space is limited, if you decide to fit a PCI TV tuner card, you will be limited as to which AGP card you can fit. A full length card is probably not recommended, and a model with a slimline (or even passive) heatsink would be best.
A better alternative would be to go for a VGA card with built in TV tuner, such as MSI TV5200-VTDF128 or an ATI Radeon All-In-Wonder card (ATI AIW is supported in WinXP MCE05)
ON-BOARD VGA
The SiS651 chipset is pretty old now, and the on-board SiS650 VGA is not up to playing any of the latest games, as it is only DirectX 7.0 compliant and does not support Hardware Texture & Lighting. However, it is adequate for playing back DVDs as it supports hardware acceleration (in PowerDVD for example), and general video output is decent. The maximum shared video memory size is 64mb.
The Mega 651 does NOT feature TV-out as standard. You can however either buy an AGP video card which includes TV-out feature, or the Mega TV-out card (availble in UK from www.dabs.com). Please note, this card is ONLY for Mega 651, and does NOT work with the 865 model. (The 180 does however, thanks to nforce2 chipset, support TV-out as standard)
ON-BOARD AUDIO
The Realtek ALC650 AC97 audio codec offers 5.1 surround sound (with suitable speakers of course ) as well as SP-DIF for digital output.
The sound quality is quite reasonable; i'm currently listening to MP3s through a set of Creative Inspire 5.1 speakers, and its certainly good enough for me.
There are three audio connectors on the rear, they default to:
GREEN - Front speakers
BLUE - Line In
PINK - Mic
To connect surround sound speakers correctly, you need to use the Realtek audio configuration tool (located in the Taskbar by the clock). Set the speaker config to 4 or 6 channel (5.1) and then click on the boxes to the right to configure the rear ports correctly
GREEN - Front speakers
BLUE - Rear Speakers
PINK - Subwoofer / Centre Speaker
NOTE: If you do decide you want to install a PCI soundcard, be aware that you will lose the Radio function in PC mode, and for audio output in Hi-Fi mode you will need to reconnect audio plugs from your soundcard to onboard sockets. The Hi-Fi mode and Radio only work with the onboard audio.
POWER SUPPLY
All the Mega series barebones come with a 200w PSU. Don't even think about upgrading to a higher output type, as the Mega PSU is a non-standard type. A standard ATX PSU will NOT physically fit inside the Mega case. Besides which, the Mega series have a special connector which powers the Bluebird hi-fi module and on-board sound when the PC is off. And there is a special Molex power connector for the CD/DVD drive, also for that to be used when PC is off.
WINDOWS XP MCE 2005
Media Center 2005 requires a DirectX 8.1 / 9.0 compliant video card with a minimum of 64mb RAM, 128mb RAM is recommended, however, for best performance. So you will need an AGP card, because SiS do not provide any MCE-compatible drivers. The TV@anywhere TV tuner (MS8606-10) and Mega TV Tuner (MS8606-40) are not supported by MCE05, because MCE2005 requires a TV card that will provide a direct MPEG2 stream, which a PVR card such as the Hauppage PVR MCE series can do (as a hardware card, MSIs card are software only and rely on drivers to do MPEG encoding), or a dedicated DVB-T card which receives an MPEG2 signal over the air.
MEGA 651 REMOTE
If you fit an MSI TV@anywhere card to your Mega 651, the Mega remote can be used to control the MSIPVS software, providing you use the remote receiver supplied with the TV@nywhere card. The Mega remote is designed to work natively with the MSI Media Center, and MSI Mega Radio programs only.
If you wish to program the remote to operate other programs within windows, then you will need a program called Girder, and the accompanying MSI plugin, kindly provided by nathan. please see his sticky thread for more info, about his plugin, and how to obtain Girder.
BROKEN HEATSINK MOUNTING CLIPS
https://forum-en.msi.com/index.php?topic=96148.0
Phew, thats about it. If any other Mega 651 users think I've missed anything out, please feel free to tell me.
For other general hints and tips, look through the "things to know" posts regarding the 865 and 180.
MEGA 651 =

Quote
PROCESSOR SUPPORT:
The official list of supported CPUs can be found here:
http://www.msi.com.tw/program/products/slim_pc/slm/pro_slm_cpu_support_detail.php?UID=431&kind=4
Basically the ageing SiS651 chipset does not support Celeron / P4 cpus above 533mhz, and does NOT support the newer "Prescott" core cpus
Celeron > 400Mhz FSB
P4 Northwood > 533mhz FSB (512kb L2 cache)
your processor is not supported. please start a new thread if you need help

MEGA 651 dual display?

Hi,
My setup is MEGA 651 with AIW ATI Radeon 8500, Win XP. As a monitor I am using Sony Grand Wega 42" LCD TV. Works great. I am using 2 connections from my video card, one is S-Video (display is somewhat blurry) and DVI (very sharp and looks like screen of a laptop). My tv allows to choose to display from different sources and those 2 connections are treated as such.
The limitation is I can only use 640X480 resolution, which is fine for movies, internet (wish I could have better resolution here).
Few days ago I got game SIMS for my kids with few expansion packs. Problem now is that they can not START the game with the resolution of 640X480, the minimum for the game is 800X600.
I found a temporary solution to use a regular monitor to start the game (I unplug DVI connector from tv and plug a regular 17" monitor into the video card), and then I switch the S-Video source on my tv to play it.
I tried to find any info if tv can support more that 640X480 but non found. If I switch to higher resolution I can not boot or if I boot in Safe Mode screen goes nuts until I reset to lower. Another option is to leave second monitor, but to use onboard VGA connector, but I can not find any info how I can use both AGP and onboard video simultaniously. Is there setting in the BIOS to enable. it seems that onboard video works only if there is no other video card installed.
Thank you for help.

Quote
how I can use both AGP and onboard video simultaniously. Is there setting in the BIOS to enable. it seems that onboard video works only if there is no other video card installed
you can only use onboard VGA or VGA card in AGP slot - you cannot use both
have you checked for any updated drivers for your video card? i use a Geforce FX5200 in my Mega 651 for TV-out, and I can select up to 1024x768 for TV resolution (though obviously its not a really useable resolution on my CRT TV, connected with composite video) though i prefer to leave it at 800x600
Quote
I am using 2 connections from my video card, one is S-Video (display is somewhat blurry) and DVI (very sharp and looks like screen of a laptop). My tv allows to choose to display from different sources and those 2 connections are treated as such.
if you are only using one display (your 42" Wega ) then i don't understand why you need to have both types of connections connected to it. if the Sony has a DVI input, that is the only option you should use, as even s-video is inferior to that by a mile

Mega 651 am/fm tuner powers on but pc doesn't

Can anyone help me out?
The thing has been working fine for over a year...but started randomly not turning on. Now it won't turn on at all. If you unplug it and plug it back in, the tuner will power up...but when you hit the pc button it goes dead.
I am running a 2.8Ghz Northwood processor with 512MB RAM.
Any ideas?
Thanks!

My MEGA 651 had the same symptoms :] , I though that it was due to the PSU, so I connected it (with some modifications) to a new 400W PSU. Now the PC switches on sometimes, but when I switch it off it won't switch on again immediately, you need to wait for several minutes. Now I am inclined to think that the problem is with the motherboard, which means that 651 is going to a dump soon :(

MEGA 651 - PSU - Am I done?

I've had my MEGA 651 for about 3.5-4 years. During that time, it has had long streaks of reliability interrupted by periods of annoyance. These usually consisted of:
refusing to turn on at times
making the hard drive spin/click - then working fine after a few hours of inactivity
making the hard drive spin/click - then wiping the boot sector or something else on the HDD
Essentially, over its lifetime, it has wrecked about 3 hard drives. Now I'm not completely foreign to PC building, but I've always treated the proprietary components of the MEGA [e.g. the PSU, hi-fi, radio, etc.] as a black box...I knew I could replace them, so I never explored them.
Anyways, these bad spells have been getting worse/more common lately. The hard drive got hit about a month ago. It also just started this new phenomenon where plugging in the cord wouldn't even boot the hi-fi mode...but after leaving the cord in for an hour or so, the hi-fi would turn on on its own, then the PC mode would work. Also, the HDD has been spin up/spin down a couple times before starting. With all these problems, I [finally] decided to investigate the PSU. Here are the CMOS readings:
Vcore
1.45-.47V
3.3V
3.29V solid
+5V
4.70-.73V
+12V
11.00-.12V
-12V
-10.65-.90V
VBAT(V)
3.02-.04V
5VSB(V)
5.10V solid
I don't know much about PSUs, but I know enough to recognize those numbers as pretty awful.
Now, I've been having about weeks of stability at a time here. My questions are pretty much:
Is this PSU dying/dead...if I keep using it, am I doomed to more power failures, broken hard drives, etc?
Is there anything I can do about it?
I'd appreciate any thoughts. I apologize for the wordy post...I was excited...I just found this forum. (For example, this last month was the first time I was able to control Meedio with the MEGA's built-in IR, because I never knew that there was a Girder plugin for the IR receiver!)
Thanks.

I can't say much, as I don't have such a system, but your 12V line seems to ve very low.

MEGA 651 - need a part for it

hi, just got a second hand MEGA 651 and noticed that the clip to hold the cpu cooler inplace is broken, how would i go about getting a replacement? Its one of the black thingys that are screwed down, i havent been able to test it yet but it looks like my cpu wont be compatable due to the fact i have got a P4 3.2ghz prescott.
Thanks.

Quote
i read on here somewhere before that they got in touch with MSI, who sent them a replacement clip free-of-charge
so it wasn't my imagination after all! there you go, a bargain Mega PC for £40

MEGA 651 problems-Help!

MEGA 651(Purchased 20th July 2004)
512Mb DDR 3200RAM
2.4Gig Celeron processor
Seagate 7200 120GB HArddisk
Leadtek A180 128MB DDR Grapics Card
Sony CD Witer
Window XP Home Edition.
I have several problems with it-
If I select anything other than safe mod in the BIOS it will not start up.
It intermitantly give me a BIOS Checksum Error, and I have to reset the Bios to make it boot.
Every time it Boots it sendsa 'This system has recovered from a serious error message to Microsoft'
It is generally very slow and applications keep 'hanging' which forces me to use task manage
I have flashed the BIOS with the latest code to try to resolve the issues, but to no avail.
Does anyone have any thoughts??? Please help is getting silly now!
Ta
Charlie

sorry i misread your original post - yes it does sound like memory issue, and i think we've seen something like this before
suggestion:
In BIOS menu,
under Advanced Chipset > Advanced DRAM Control
set System Performance to Normal
under Frequency/Voltage control
set DRAM frequency to 333MHz (speed of PC2700)
this should force the system to operate the memory at PC2700 speed, and hopefully will cure the problem - as the memory clock is operating at the same speed as the cpu fsb, which is the most stable condition
let us know how you get on - if that doesn't work, I would recommend getting a PC2700 stick of ram thats NOT corsair, i seem to remember some other users having problems with this brand - i'm using crucial pc2700 and thats fine (runs System Performance at Fast!)

Can anyone help? Hibernating Mega 651 (fao Stu Online)

Hi All,
I'm new to this forum as I've only just found it existed!
I have finally built my Mega PC 651 (the orange and silver one).
Huge amounts of stress building it with temperature issues, noise, and OS problems.
I thought it would be easy using all MSI equipment to ensure compatability, but not so. Win XP caused huge problems with the MSI DR16 B DVD writer (not refreshing drive info and no access) so went back to using Win 2k. Also MSI Live updates stopped my MSI nVidia Personal Cinema working (nvarem.exe problem).
Anyway got it all working, apart from the hibernate function.
I have enabled it on Windows 2000 Power Options menu and gone into the bios and change the power button function to 'suspend'.
When I press the power button now windows starts hibernation then everying goes off but the 651 just reboots. Sometimes it does hibernate but mostly it reboots.
Also after awaking from hibernation windows displays a warnig that usb device has been unplugged without stopping, I assume this is to do with the card reader on the Mega.
Anyone know how to sort this?
Many thanks,
Mo
MSI Mega 651
P4 2.8GHz 533 FSB
Akasa Expansion Slot Exhaust Blower
Akasa Pax Mate II in case sound insulation
1Gb Corsair Matched pair DDR RAM
MSI FX5200-VT128 nVidia Personal Cinema
MSI DR16-B DVD writer

My MEGA 651 had the same symptoms :] , I though that it was due to the PSU, so I connected it (with some modifications) to a new 400W PSU. Now the PC switches on sometimes, but when I switch it off it won't switch on again immediately, you need to wait for several minutes. Now I am inclined to think that the problem is with the motherboard, which means that 651 is going to a dump soon :(

Mega 651 USB devices disappearing after wakeup from Hibernate state - HELP!

Hi All,
I still have this problem where when I wake up my Mega 651 from a hibernate state my USB devices seem to get uplugged or ejected. The usb ejected/unplugged window appears also.
This wasn't too much of a problem, however, my PC is now on a network and when my usb devices are unplugged such as my UPS or shared printer a broadcast message is sent to all network PC's.
I've also started using my card reader as I now have a digital camera, but annoying when the card reader is ejected all the time.
I'm running Windows 2000 SP4 with all updaes.
If anyone can help me solve this problem it would be a great help.
Also the card reader access light stays on sometimes after shutdown, why is this?
Many thanks,
Mo
MSI Mega 651
P4 2.8GHz 533 FSB
Akasa Expansion Slot Exhaust Blower
Akasa Pax Mate II in case sound insulation
1Gb Corsair Matched pair DDR RAM
MSI FX5200-VT128 nVidia Personal Cinema
MSI DR16-B DVD writer

Suspend has always been problematic under Linux. It seems to be hit or miss for the most part, but here are some things you can try:
Use an LTS kernel, tuxonice, pm-utils, etc. See Suspend and Hibernate
Try a different graphics driver
Tweak the driver module parameters or build your own driver.
Unfortunately I don't have experience with the radeon driver, so I can only give you ideas.

TS4471 Aperture wont start

All of a sudden Aperture wont start. I click the icon on the dashboard and an error pops up. I tried several times. I uninstalled Aperture and installed again. No result.
I know, it's in Dutch, but I think the type of error seemd formiliar. Here are the details:
Process:         Aperture [976]
Path:            /Applications/Aperture.app/Contents/MacOS/Aperture
Identifier:      com.apple.Aperture
Version:         ???
Build Info:      Aperture-451099000000000~1
App Item ID:     408981426
App External ID: 107312636
Code Type:       X86-64 (Native)
Parent Process: launchd [184]
Responsible:     Aperture [976]
User ID:         501
Date/Time:       2014-04-18 20:28:22.068 +0200
OS Version:      Mac OS X 10.9.2 (13C64)
Report Version: 11
Anonymous UUID: 6790C229-BD91-245B-3C98-152097B9DA9B
Crashed Thread: 0
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Application Specific Information:
dyld: launch, loading dependent libraries
Dyld Error Message:
Library not loaded: /Library/Frameworks/PluginManager.framework/Versions/B/PluginManager
Referenced from: /Applications/Aperture.app/Contents/MacOS/Aperture
Reason: image not found
Binary Images:
    0x7fff6d277000 -     0x7fff6d2aa817 dyld (239.4) <2B17750C-ED1B-3060-B64E-21897D08B28B> /usr/lib/dyld
    0x7fff8a223000 -     0x7fff8a286ff7 com.apple.SystemConfiguration (1.13 - 1.13) <63B985ED-E7E4-3095-8D12-63C9F1DB0F3D> /System/Library/Frameworks/SystemConfiguration.framework/Versions/A/SystemConfi guration
    0x7fff8a291000 -     0x7fff8a3b3ff1 com.apple.avfoundation (2.0 - 651.12) <5261E6EA-7476-32B2-A12A-D42598A9B2EA> /System/Library/Frameworks/AVFoundation.framework/Versions/A/AVFoundation
    0x7fff8b2fd000 -     0x7fff8b2fdfff com.apple.Carbon (154 - 157) <4E260C09-78F4-305B-B408-13321CAF6213> /System/Library/Frameworks/Carbon.framework/Versions/A/Carbon
    0x7fff8b3f4000 -     0x7fff8b3f9fff com.apple.DiskArbitration (2.6 - 2.6) <A4165553-770E-3D27-B217-01FC1F852B87> /System/Library/Frameworks/DiskArbitration.framework/Versions/A/DiskArbitration
    0x7fff8f5ab000 -     0x7fff8f646fff com.apple.PDFKit (2.9.1 - 2.9.1) <F4DFF4F2-6DA3-3B1B-823E-D9ED271A1522> /System/Library/Frameworks/Quartz.framework/Versions/A/Frameworks/PDFKit.framew ork/Versions/A/PDFKit
    0x7fff8fb8d000 -     0x7fff8fde6ff9 com.apple.security (7.0 - 55471.14) <3F7100A0-FE46-333D-9A4B-396580F1B4FE> /System/Library/Frameworks/Security.framework/Versions/A/Security
    0x7fff912bb000 -     0x7fff913f1ff6 com.apple.WebKit (9537 - 9537.74.9) <CA0C0387-8A66-34D4-8B1C-F5CDDBDA76BB> /System/Library/Frameworks/WebKit.framework/Versions/A/WebKit
    0x7fff918a7000 -     0x7fff918a7fff com.apple.CoreServices (59 - 59) <7A697B5E-F179-30DF-93F2-8B503CEEEFD5> /System/Library/Frameworks/CoreServices.framework/Versions/A/CoreServices
    0x7fff918ae000 -     0x7fff918aefff com.apple.Cocoa (6.8 - 20) <E90E99D7-A425-3301-A025-D9E0CD11918E> /System/Library/Frameworks/Cocoa.framework/Versions/A/Cocoa
    0x7fff91a04000 -     0x7fff91be9fff com.apple.CoreFoundation (6.9 - 855.14) <617B8A7B-FAB2-3271-A09B-C542E351C532> /System/Library/Frameworks/CoreFoundation.framework/Versions/A/CoreFoundation
    0x7fff9218c000 -     0x7fff92328ff3 com.apple.QuartzCore (1.8 - 332.3) <80F1068F-4A34-34FB-9E05-A2DC0700D2F2> /System/Library/Frameworks/QuartzCore.framework/Versions/A/QuartzCore
    0x7fff92941000 -     0x7fff9294ffff com.apple.opengl (9.6.0 - 9.6.0) <709F4A02-73A0-303C-86B5-85C596C8B707> /System/Library/Frameworks/OpenGL.framework/Versions/A/OpenGL
    0x7fff93c04000 -     0x7fff93c04fff com.apple.ApplicationServices (48 - 48) <3E3F01A8-314D-378F-835E-9CC4F8820031> /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Application Services
    0x7fff95587000 -     0x7fff95818ff7 com.apple.AOSKit (1.06 - 176) <35525B2F-B02F-31FD-A3B2-FD6AE6D32C11> /System/Library/PrivateFrameworks/AOSKit.framework/Versions/A/AOSKit
    0x7fff95a08000 -     0x7fff95a51fff com.apple.CoreMedia (1.0 - 1273.49) <D91EC90A-BFF1-300D-A353-68001705811C> /System/Library/Frameworks/CoreMedia.framework/Versions/A/CoreMedia
    0x7fff95bbb000 -     0x7fff95c25ff7 com.apple.framework.IOKit (2.0.1 - 907.90.2) <A779DE46-BB7E-36FD-9348-694F9B09718F> /System/Library/Frameworks/IOKit.framework/Versions/A/IOKit
    0x7fff9623a000 -     0x7fff9623afff com.apple.Accelerate (1.9 - Accelerate 1.9) <509BB27A-AE62-366D-86D8-0B06D217CF56> /System/Library/Frameworks/Accelerate.framework/Versions/A/Accelerate
    0x7fff9683e000 -     0x7fff9689cff7 com.apple.corelocation (1486.17 - 1486.24) <9FBB29F0-E000-3190-A96C-9EAA5CCCA2A0> /System/Library/Frameworks/CoreLocation.framework/Versions/A/CoreLocation
Model: MacBookPro10,2, BootROM MBP102.0106.B03, 2 processors, Intel Core i5, 2.5 GHz, 8 GB, SMC 2.6f59
Graphics: Intel HD Graphics 4000, Intel HD Graphics 4000, Built-In, 1024 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1600 MHz, 0x80AD, 0x484D5434314753364D465238432D50422020
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1600 MHz, 0x80AD, 0x484D5434314753364D465238432D50422020
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x10F), Broadcom BCM43xx 1.0 (5.106.98.100.22)
Bluetooth: Version 4.2.3f10 13477, 3 services, 23 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en0
Serial ATA Device: APPLE SSD SM128E, 121,33 GB
USB Device: Backup+ BL
USB Device: Hub
USB Device: FaceTime HD Camera (Built-in)
USB Device: Hub
USB Device: Hub
USB Device: Apple Internal Keyboard / Trackpad
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
Thunderbolt Bus: MacBook Pro, Apple Inc., 23.4

That is a familiar error message.
You probably installed Final Cut.
http://support.apple.com/kb/ts3528
Dyld Error Message:
Library not loaded: /Library/Frameworks/PluginManager.framework/Versions/B/PluginManager
Referenced from: /Applications/Aperture.app/Contents/MacOS/Aperture
Reason: image not found
The installation has replaced a dynamic library (PluginManager.framework) by an incompatible version, and the best option to restore this necessary framework will be to reinstall MacOs X. You can reinstall Mavericks on top of your current system, so you need not to reinstall anything else.

MEGA 651 doesn't boot

Hi everyone,
I am using the mega651 for 1.5 years, almost without problems. Yesterday I tried to reboot the box, it shut down properly, but instead of booting, only psu and gpu fan started, the cpu fan did not, and it didn't show any POST Messages. I checked all cables, but they seem to be ok
I built out my graphics card, and it worked, then I again tried with the card, and it worked too. Ok, panic over,
Today I tried to boot the box, and the same problem occured (with and without gpu)
It seems like it's booting when it wants too...
my specs:
mega651
p4"northwood"2.8ghz
sapphire x800se
512Mb infineon DDR400 Ram
LG GSA 4167B DVD+/-RW
Any Idea?
nrn

Hi Stu. Sorry if U feel offended by my message. I've spent a lot of time trying to find the reasons (at least) of this strange behaviour of this barebone. I've looked through russian forums (I'm from Russia) and I see that a lot of people have met the same problem for the last 1.5 years. So, if people in different countries meet the same problem with the same product then the absence of MSI's recommendations shows the level of their "respect". Of course I'd like to get your help if it is possible. My 651 optional devices are:
P4 2.4 MHz, 512 MB, Radeon 7500, 80 GB Barracuda 7200.7, MS-8216S DVD
Everithing was OK for the first 1.5 year, but last winter brought the problem described by many other people: the device comes "freezed" in 1 second after pressing "PC" button on front panel. Fans are working, PC LED lights, display is black, device doesn't respond to any buttons. The only way to make it alive again is to disconnect every wire from it, then "clear CMOS" with corresponding pin and leave barebone unplugged for a couple of days (a few hours don't help ). Idea about capacitors is just a kind of a logical trick: batteries and capacitors use to loose their prferences with time, other elements use to become "not working at all"... I can change capacitors in PSU for new (good) ones, but a lot of people say that changing PSU hasn't helped. So should I try to spend time (and capacitors:) ) for this? (I'm not kidding, it's a real question). In Russian forums some posts say that different Service centers declare the reason of this behaviour as "undefineable motherboard problem" But during the last few months every PSU voltage have lost approx. 15% of nominal value! (f.e. +12V could become +10.3V and so on)! Something definitely keeps on dieing in PSU! Maybe in motherboard too? Anyway I'm writing this message on my Mega 651, but I never know when it stops again :( Last time it was dead for a week!

Mega 651 sound problem

My sound refuses to work. I've got the newest drivers and xp
says that it works fine but theres no sound.
I've got a ordinary power supply, not the one that came with the mega 651.
so i dont have the small black, brown, purple cable. Can it be the problem?

I'm having a similar problem.
It's amazing really, it's one sodding thing after another. I now have my Mega 651 back to perfect running order after months and months of niggly little problems, I think I *finally* have the thing sorted, and now...NO SOUND. The speakers and amp work perfectly (I have tested this) and I have even fitted a brand new soundcard...but nothing.
Any suggestions as to where to start looking please?

Satellite A660 wont start again until i turn to safe mode

Just purchase toshiba Satellite A660: i tell the story to compensate closely to my answer, hopefully ..
I just purchase it new, run the insallation program for first use. When its up and running just within that day i noticed that it start to hang up when i hooked external drive for some program installation (adobe lightroom).
Its still fine but when i turn it off, it wont start again until i did turn to safe mode so that i could back up some of the files and run the recovery again.
This time on 64bit. When its finish its process, it works well for just a couple of hours.
It fell faster now thou, maybe because its on 64bit? ( any recommendation whether its 32 or 64bit) specs: i5 , 4ram, 1g ddcatd graphics , win7 home premium, ..
Now, when i turn it off it never start back again windows say.. start up repair. ..
I did let it run since this morning until now still they cant find whats the problem (i'm refering the loptop) .
So any idea on whats goin ?

> It fell faster now thou, maybe because its on 64bit? ( any recommendation whether its 32 or 64bit) specs: i5 , 4ram, 1g ddcatd graphics , win7 home premium, ..
64bit Operating system is better if your notebook supports 4GB or more RAM.
Why? Because Win 32bit recognizes max 3.2GB even if more RAM is available.
This is 32bit limitation; no matter what OS it is; Linux, Win XP, Vista, Win7 etc
This is the reason why 64bit OS are so popular in the last time
Regarding the OS issue;
I recommend running a HDD recovery again... this means you should reinstall the OS usign the Toshiba recovery option;
Press F8 while powering up the notebook, Choose Repair my Computer, -> HDD recovery

After Effects just bounces in the dock but wont start

Hi all,
Just installed CS4 production studio under Snow Leopard. All works well and updated using the Adobe Updater. All apps are fine except AE which just bounces in the dock a few times and then stops. I read that this could be because Rosetta was not installed. I installed Rosetta from the Snow Leopard DVD and still nothing. Have restarted 3 times just in case (I also read that several restarts may be required to get it to work), but still nothing.
Any help would be greatly appreciated.
Regards
Dave

OK... Now I feel like Scott of the Antartic writing in his journal before the inevitable... I am writing this purely to help anyone else with the same issue to resolve it without the pain that I am still experiencing. Hopefully the last entry will read "all solved" and not "I am about to pop outside... I may be some time..."
After using CS2 for the bulk of my work I thought I'd try and get this solved once and for all, especially as we have a DVCPROHD project coming up and need CS4 to do it.
OK... The so now I have the suite running, except Premiere is running under at trial without the presets and the updates fail when installing. Contacted support this week, they wont re-open the original case because it has been over a month. Fair enough, new case.
The adobe guy takes control of my machine, deactivates it, then from Finder deletes lots of folders. He then asks me to re-install the products. I do this (2 hours later) and run Premiere and it appears to work with presets. I look a bit closer and notice that under the help menu of Premiere Register, Deactivate and Updates are all greyed out. This is not the case in the other products of the suite. OK, so not a major deal but does imply something is not installed right. I run the Adobe Updater, Premiere updates, but AE, PS and several updates fail.
Call back to support. This time the Adobe guy takes control of my machine suggests I deactivate the suite, run the un-install and then download and run the CS3 Clean script and re-install. I do all this. Another 2 hours later feeding discs into the machine... and... Premiere looks fine, presets all there... but wait for it... AFTER EFFECTS JUST BOUNCES IN THE DOCK BUT WONT START.
3rd call back to support and ask for the issue to be escalated. This is difficult and I have to cause a fuss to realise that this problem is the same one that has been hanging around for months and that I am not prepared to spend more hours removing every trace of Adobe from my machine and re-installing - this doesn't work. The support technician asks me to delete a hidden folder that has all the Adobe patches in it, manually download the AE 9.0.2 update and install it. It installs but AE wont start. I explain that I've had enough and want the problem escalated.
I finally get a call back from a 2nd level engineer this morning. After explaining the that AE wont start and then answering the question "why is this a problem for you!" we do some quick troubleshooting. This time I have to pull out the network cable, turn off Airport, create a new user account, log on to it and then see if AE runs. Which it does. Within seconds we get launched into the pre-determined script, "if it runs under another user account then there is nothing wrong with the applications and I should call Apple". After being patronised for a further 5 mins I had to PROVE to the guy that it was also possible that the fault was Adobes. I also know the moment I phone Apple, the response will be "Call Adobe".
The only example I could give him at the time was to image a piece of software I had written that allocated memory based on the screen resolution (this is a user preference) and if my code was badly written and crashed when encountering a screen resolution bigger than my code was expecting. OK, is that Apple's fault, no it is my code. Will it run under one user and not another, yes it will. There are a million other posibilities. Some I agree could be Apple's, but equally some could be Adobes and the big fat fob off as soon as you can is terrible.
I have also since realised since leaving this call with the technician, that:
1) This is a brand new iMac and the Adobe Suite was the 1st piece of 3rd party software installed on it.
2) The iMac is for video editing and nothing else.
3) This was working without presets before the Adobe guys deleted all these files and asked me to re-install. It is more likely that they have deleted something they should not have rather than the a bug in the OS. A bug in the OS is still possible but I suspect the problem is with a rogue bit of installation code from Adobe.
Finally incase anyone from Adobe is reading this:
I have paid thousands of pounds for this software.
I have been unable to use it for months.
A problem like this should be gold dust for you. Here is the chance to get to the bottom of an issue that several people are having, understand the mechanics of what is going wrong. Write a KB article as well as a patch and this would save the time/money and effort of an awful lot of people (including your own).
As a short thought experiment I would like everyone at Adobe to image the following:
You pay £1,000 of your own money for a tool to do your work on the promise that you can make this money back in productivity gains, new business, etc.
The tool you use every day to make a living won't work. For the benefit of the experiment, imagine this is your email client, web browser or case management tool.
You have no IT group to replace your machine or to come and solve it.
You can't tell your customers that your software is down and you have to keep doing your job.
You have to spend an additional 3 days in your own time, working late or weekends to try and fix the software yourself.
You to keep downloading a Gigabyte of data 3 or four times and you have to pay for downloads. Currently you are running up a bill of over £100 in downloads and phone calls.
You don't get paid the overtime and your customers start complaining you are late with your work.
You lose customers... you eventually get fired because you have lost too many of them.
...This is what it feels like for a small creative business to not be able to install the software they bought.

My mega 651 wont start

Similar Messages

Maybe you are looking for