My MG3200 printer is showing "printer not responding" after installing new ink cartridges.

Ever since I replaced the ink cartridges in my printer it won't print showing a not responding error. I have tried troubleshooting but still doesn't work

Hello,
If you are using the printer on a wireless connection, check out the link below for step-by-step procedues you can try:
http://kbsupport.cusa.canon.com/system/selfservice.controller?CONFIGURATION=1011&PARTITION_ID=1&secu...
If you are using a USB connection, try this:
http://kbsupport.cusa.canon.com/system/selfservice.controller?CONFIGURATION=1011&PARTITION_ID=1&secu...
However, if the issue persists, please reach out to our technical support team at http://bit.ly/Phone_Support
Thanks!
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

Printer not working after installing new cartridge

have HP D5460 printer. Installed new black cartridge only #564 since I only use black ink. Error message appeared
"Oxc19a0020 turn printer OFF & then ON". Did that and also checked to be sure cartridge was installed properly. It Was.
I can't get the printer to work. What now? Thanks.

The battery is already full. It happened suddenly and started showing low battery sign and sign to charge the ipad. Nothing happening with pressing buttons or even putting on for charging for quite some time.
iPad (3rd gen) Wi-Fi, iOS 7.1

Officejet 8000 - Printer says out of ink even after installing new ink cart. and new head.

My Officejet 8000 - Printer says "out of ink even after installing new ink cart. and new print head. I have tried two new cart. and still gives me the error. A few times it will show all inks are full and print a page or two then says it is out of ink. At one point I even was able to clean the heads and align them but same thing occurs. What is wrong??

Hi Lee_S
Try printing a Self Test Page and see what the Cartridge status & Printhead status is like.
Printing a self test page
Please let me know how you get on..
Thanks, Ciara
Although I am an HP employee, I am speaking for myself and not for HP.
Twitter: @Ciara_B_HP

Firefox Not Responding after Installing Microsoft Office 10

After installing Microsoft Office 10 (student and home edition) on my laptop, I noticed that Firefox is going into the state 'Not Responding' every time I access it - it takes about 10 secs to 'think' and then comes back online. It continues to do this every time I want to access a new page, new link, click on mail in Yahoo Mail, etc. Has anyone experienced this issue?

1) Check the $IAS_ORACLE_HOME/Apache/JServ/etc/logs/jvm
has servral logs for OACoreGroup Servlets that are initialied
2) You might have to enable the debug option in jserv.properties and jserv.conf
(find IsItWorking.java in Metalink for the appropriate note )
3) If this is 403 forbidden then check trusted.conf alongside httpd.conf
pls keep posted about how this issue got resolved.
Sunil
JSP not responding after installing 11.5.10.2 on IBM
HACMP
i have finished installing Oracle applications
11.5.10.2 on IBM clusters (HACMP version 5.1)its a
multinode setup with mutual failover. other
applications are working fine. the installation went
well. but the final part on the middle tier , during
the post install checks it says JSP not responding. I
checked the apache error-log and saw the follwoing
entry
[Sun Apr 23 21:04:21 2006] [error] [client
172.29.200.74] client denied by server configuration:
/appl/oracle/devcomn/portal/
DEV_erpappssrv/oprocmgr-service
>
that bafles me because that ip address was not used
in the installation. its the persistent ip address of
the HACMP. the service ip that was used in the
configuration file was 172.29.200.75
however there is no mention of this in the error
log.i also edited the oprocmgr.conf in the
Apache/conf directory after which i dont get the
error however the servlets pages then hangs and
returns page cannot be displayed error on internet
explorer. no error is registered on the error log.
the jdk am using is 1.4.2 which is the recommended
one.
what this means is that i cannot access the self
service pages and as you know you need self service
pages to access the application in 11.5.10.2
i opened a TAR with oracle on 8th April 2006 and till
today i have not been able to get a solution.
I am hoping that i will get someone in this forum who
has met a similar problem or who has an insight into
how we can solve this problem already am weeks past
the target go live!!!
Please Kindly help
Jeremiah Ochieng

HT4623 my phone main button not working after installed new version software 7.0.6

my phone main button not working after installed new version software 7.0.6

Arrange some liquid like petrol spirit and w 40
two drops in to home button.
30 times press slowly slowly and then restart your apply iphone.
You will get ready.
I am sure. Thanking you...

IJ Canon Printer Utility disappeared after I replaced ink cartridges.

I just replaced the ink cartridges with ones I ordered from eforcity and it prints fine, but I haven't been able to locate the printer utility box ever since which means I haven't been able to check ink levels and clean the nozzles. This is really frustrating because I need to clean the print nozzles now. Every line on my printouts is streaking (half dark / half faded). Help! Thanks.

Hi , Welcome to the HP Forums! I see that you cannot print with your HP Officejet Pro 8500A, on Windows 7, after replacing your Ink Cartridges. I am happy to help! Please, try the steps within this guide, Fixing Print Quality Problems for the HP Officejet Pro 8500A e-All-in-One Printer Series. If the guide does not resolve your issue, Please contact HP, phone support for further assistance. If you live outside the US/Canada Region, please click the link below to get the support number for your region. Country-language selector. Hope this helps! “Please click the Thumbs up icon below to thank me for responding.”

Garageband Not Responding after Installing Pro Tools 8 LE

So, after having installed Pro Tools 8 LE, I want to use GarageBand, and after clicking the icon, it keeps bouncing. The program does not open and on the Activity Monitor it shows and "Not responding". Any ideas? Thanks! I'm running Mac Os X 10.7.5

Que Tal Amigos, en busca de este problema en diferentes foros, me di a la tarea de traducir cada unos de sus preguntas y dudas ya que no se ingles, por lo tanto espero que se den a la tarea de traducir esto a su idioma ya que tengo la solucion de este Gran Problema que tenemos todos los que actiuaizamos a Lion OSX 10.7...buen ahi les va al parecer uno de los drivers midi de las superficies de control o interfaces de Avid 002 y 003 utilizan este para poder utilizar sus in/out midis ya que si tu eres de los que no tiene esta interfase o no utilizas estas salidas y entradas es preferible que borres o cambies de ubicacion a alguna carpeta "como la de Plugins unused" este archivo...Library/audio/mididrivers/DigiDioMidiDriver
este driver es el que crea conflictos entre Garageband,Logic y Protools, hoy lo he echo y todos mis programas van de maravilla...Protools 8.0.5, Logic 9.0.5 Garageband etc...Espero se de gran ayuda ya que estuve por muchos foros y nunca encontre la respuesta,pero mis pocos conocimientos de audio me hiceron llegar a esta conclucion....saludos y Feliz Dia De Gracias......
atte Mexicano Terco....

Wifi connection with 4s not working after installing new software ios6

wifi connection with 4s not working after installing ios 6.

Go to Settings > WiFi > Select your network and hit the right arrow to "Forget Network"
Then go to Settings > General > Reset Network Settings and try connecting again when the phone restarts.

Will not print black ink after installing new HP cartridge

HP Officejet 4620, Windows 7....installed new HP black ink cartridge and now it will not print black at all. I followed all online tips in the help section, even cleaned the vents on the cartridge itself but only prints blank page. No error messages are shown. Diagnostics ran and says all is working correctly. Also cleaned printheads through 2 cycles still nothing. Any other suggestions? It was working just fine before inserting new black cartridge.
This question was solved.
View Solution.

I just spent 1 1/2 hours on the phone with HP Tech Support but it was worth it. They are sending a replacement printer no charge to me (expect I chose to pay extra for next day shipping). Even though my printer is out of warranty!!! I normally buy HP products anyway but will definintely stay with this brand based on their excellent customer service and support. Thank you once again for your initial help online and for directing me on the right path!!!

Adobe not responding after installing upgrade to Windows 8

Im having a problem since upgrading operating system to Windows 8 (pro). Since the upgrade whenever I use Adobe the system goes extremely slow to launch and sits on not responding for a period of time. Eventually it will load but am still uanble to do anything with the document in Adobe, cant print, cant move up and down document.
Is anyone else having this problem.

< suspicious activity removed by host >

INSTALLED NEW INK CARTRIDGE and cancelled the alignment PRINT HEAD IS STUCK

Greeting everyone
I just put a new color 57 HP ink cartridge into my all in one 2210 printer & somehow I cancelled the alignment as it seemed not to be doing anything....and now it will not return the printer head and will do nothing.... how will I fix this?
this is just a printer problem as the printer was working fine before I changed the ink. My Dell inspiron 580 wi PC is working fine and I have been printing direct from my computer to printer every day until my goof up...... intel core (TM) i5 CPU @3.20 GHz 64 bit 8.00 GB RAM
Thank You Mary Svinth in Waldport Oregon Coast
[Personal Information Removed]

Hi - A couple of things to try:
- Unplug the power from the back of the printer.
- Open the top cover, and slide the carriage to the center.
- Remove the cartridge and try reinstalling. Make sure the ink cartridge snaps in and is firmly held by the carriage.
- Plug the power cord back into the printer and power it on.
If that doesn't work, try repeating the steps above, but this time, remove the USB cable, which will completely isolate the printer and narrow down the issue.
Hope that helps.
Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
I am an HP employee.

HP Deskjet F4200: Won't Print In Black After Installing New HP Black Ink Cartridge (XL)

I am reading on this board that this problem exists on a lot of other HP injet printers.
One post is a detailed post on how to dis-assemble a F4620 to access the clogged print heads so that you can unclog it by running it under hot (tap) water.
It seems that these products were designed poorly, or with planned obsolescence so when this problem occurs (usually outside of warranty) and you call you tech support, HP will try to get more money of you by having you subscribe to post-warranty tech support, or better, have you end up buying another HP injet, and have the same issue again down the road.
It the print heads could be accessed and removed for sevice more readily, this problem would be more easily dealt with by most users.
Does anyone know if the dis-assembly instructions for the F4620 are the same for the F4200? Or better still, is there a U-tube out there on how to access/dis-assemble the F4200 to remove the print head for servicing (unclogging)?

The Officejet 4620 has an entirely different design from your printer. It has permanent printheads with separate ink supplies. [I strongly discourage folks from disassembling the printhead on the Officejet 4620 to clean it, the likely result will be a damaged printer. It would be much better for these folks to call HP support regardless of warranty as described in the post here. If they are in the US call 1-800-HPINVENt, elsewhere see the contact information here.] This does not apply to your printer.
The Deskjet F4200 series printer you have is an entirely different design. Your printheads are integrated into the print cartridges, and replaced with each cartridge replacement. In your other post I gave a link for troubleshooting steps for your printer, which would lead to this document. If the steps there do not resolve the issue I would suggest removing the black cartridge and gently blotting the printhead on a damp tissue. This should result in a strong black blot. If there is no ink at all it is possible the protective tape was not removed (sometimes the pull tab can separate from the tape. leaving the tape on the cartridge). If there is just a weak smudge of ink it is possible the cartridge is defective. In this case you could contact your dealer or HP for a replacement. If you want to take a more immediate action you could try soaking the printhead as follows: put about 1" of very hot (but not boiling) water in a teacup. Put the cartridge in the teacup with its nozzles pointing down and let it soak for ten minutes. After soaking remove the cartridge and gently dry the electrical contacts with a lint free tissue. Replace the cartridge in the printer and print a test page.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

PShop CS2 (Not responding) after installing

I have just reinstalled Adobe Photoshop CS2. It appears to install okay. When you start it up it appears to start okay, the splash screen appears and goes through the start up, that disappears and the normal working page appears, but as soon as I click on any menu,tool etc. it goes blank with the top left corner of the working page showing Adobe Photoshop (not responding). I also tried a "repair" from the unistaller, but no joy.
For info:
I am working on a Dell Dimension 9150 I am running XP pro sp3. AV is AVG and firewall is Comodo. I have never been able to get PShop working on this computer, so I don't think it is a PShop problem. I have stacks of disk space, and 2Gb RAM.

Presume you have solved this but if not, uninstall PS2 ( I also unistalled all other versions I had PS5, etc), re-install, then install 9.02 update.
Did all this then accessed CS2 - no probem.
Think it may be a multi-processor problem.

SAP B1 always not responding after install in Windows 7

Dear All experts,
I have one client machine after change to Windows 7, the client SAP B1 always show not responding or seems like "freeze", cannot do any thing while user only open some marketing document. But the othes application like Ms Office or others than SAP B1 still can be respone.User have to end process the SAP B1. Sometimes it will create the dump file. Only user's machine with Windows 7 will happen this, others like Windows XP does not facing this problem.
This issue happen since user change to new machine with Windows 7. Previously, user is using Window XP and does not happen this issue. The current version is SAP B1 2007A SP01 PL 7. The work around we have done is check the FMS, addon, and reformat the machine to reinstall Windows 7, turn off UAC setting. Please advise.
Thanks & Regards
Angie

Hi,
What windows 7 edition are you using and is it one of this following :
- Professional, Enterprise & Ultimate
Edition
if yes, it is okay that you have done the work around. I suggest to consider the sql native client (sqlnc) installation. Use the correct version of sqlnc. you use 2008 version for SQL 2008 and 2005 version for SQL 2005. Also, check if you have installed .net framework 1.1 or 2.0.
What about the PC hardware and software spec. are you using B1 system requirement guidance ?
Many causes that make slow performance in B1 especially when you are using B1 2007A SP01 PL07. I said that because it is the previous PL that approved by SAP to use in win 7. So, try to upgrade to latest PL i.e. PL11. See if the problem still persists. Let's know if persists.
JimM

Storage Provider not responding after installing SCVMM 2012 R2 UR5

After installing UR5 registered storage providers show Not Responding. I had two registered, both scale out fileservers in the same domain as VMM that were working fine before UR5. Sofs running 2012R2 with latest patches
Trying to refresh provider:
Error (26101)
Storage discovery of provider {0869e333-12f6-44c7-b6b7-7139530a18c9} for user hyper-v\<user> failed from VMM01.hyper-v.blaa.com with error code 46010.
Recommended Action
Specify valid provider, port and user credentials for storage discovery.
The other one I deleted to recreate it. The deletion yielded:
Error (26312)
Unregistering the storage subsystem with unique ID {bca715fb-ce94-47f5-9558-f8e862c3e7dc}:SS failed from VMM01.hyper-v.blaa.com with error code 46005 [SM_RC_SUBSYSTEM_NOT_REGISTERED].
However the storage provider was removed and now if I run Get-SCStorageProvider i can't see it. When I try to add it back I get an error :-(
Error (26311)
Registration of the storage subsystem ss02.hyper-v.blaa.com for user hyper-v\<user> failed from VMM01.hyper-v.blaa.com with error code 4 [SM_RC_GENERIC_FAILURE].
Not sure what's happening but looking at the roleholder in the storage cluster I have an error in the VMI-Activity log:
Log Name: Microsoft-Windows-WMI-Activity/Operational
Source: Microsoft-Windows-WMI-Activity
Date: 2015-02-23 00:11:52
Event ID: 5858
Task Category: None
Level: Error
Keywords:
User: SYSTEM
Computer: xxx
Description:
Id = {99940B20-4D23-0003-FC56-D599234DD001}; ClientMachine = SS02-1; User = HYPER-V\xxx; ClientProcessId = 332; Component = Unknown; Operation = Start IWbemServices::GetObject - root\Microsoft\Windows\Storage\Providers_v2 : SPACES_StorageProvider.ObjectId="{0869e333-12f6-44c7-b6b7-7139530a18c9}";
ResultCode = 0x80041001; PossibleCause = Unknown
And a Security error:
Log Name: Security
Source: Microsoft-Windows-Security-Auditing
Date: 2015-02-23 00:11:52
Event ID: 4656
Task Category: Other Object Access Events
Level: Information
Keywords: Audit Failure
User: N/A
Computer: ss02-1.
Description:
A handle to an object was requested.
Subject:
Security ID:
HYPER-V\xxx
Account Name:
xxx
Account Domain:
HYPER-V
Logon ID:
0x117FC549
Object:
Object Server:
WS-Management Listener
Object Type:
Unknown
Object Name:
Unknown
Handle ID:
0x0
Resource Attributes:
Process Information:
Process ID:
0x14c
Process Name:
C:\Windows\System32\svchost.exe
Access Request Information:
Transaction ID:
{00000000-0000-0000-0000-000000000000}
Accesses:
MAX_ALLOWED
Access Reasons:
Access Mask:
0x2000000
Privileges Used for Access Check:
Restricted SID Count:
0

UPDATE:
Managed to get a window to reboot the storage cluster with the incomplete delete. After rebooting the registration of the storage provider completed and is now ok. Will try to reboot the other storage cluster as well.

My MG3200 printer is showing "printer not responding" after installing new ink cartridges.

Similar Messages

Maybe you are looking for