My mid 2007 macbook powers on and gets a white screen no apple logo or spinning wheel
I Installed anew hard drive and bought OS X 10.6 snow leopard install dvd but I don't know how to install it on help.
Maybe you should have let 'these experts' also do the installation...
http://www.apple.com/support/snowleopard/
http://manuals.info.apple.com/MANUALS/1000/MA1172/en_US/Snow_Leopard_Installatio n_Instructions.pdfhttp://www.apple.com/support/snowleopard/
Similar Messages
-
imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black
Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling -
I get a white screen with apple logo and progress bar on my imac mavericks
I get a white screen with apple logo and progress bar ,then computer shuts down
when I turn my imac back on same thing happens,every time same thing
pprogress bar only goes half way then computer shut down
is there a solution ?
if not is there a way to at least salvage some files and docs?
i Have the latest imac 27Thanks I tried it but after I repaired my disk via disk utility at start up, it told me that
my disk can't be repaired and to try to back up my files so I can format it
but is there to back up my files?
also what I get is white screen with the progress bar not grey -
after running mac tuneup got a red dot on the hard drive icon, nothing would respond, now on restart cant get past white screen with apple logo, mac tune up disk still in laptop
Restart your MBP holding the trackpad down and hopefully the disk will be ejected. Then try to return it and get a refund or put it in the trash. There is nothing that software does for your MBP that you cannot do yourself or with free software.
If can get your MBP started, delete all traces of the offending software. Worst case is that you may have to erase the HDD and reload the OS and your user data. I trust that you have a backup (minus MacTuneUp).
Courcoul has given you his opinion in a very succinct manner, and as you might surmise, I agree with him.
Ciao. -
When i start my mac and i got white screen with apple logo
when i start my mac and i got white screen with apple logo n spening round n round
Try here
https://discussions.apple.com/thread/4917686?start=0&tstart=0 -
MacBook Pro won't get off startup screen with apple logo. Help?
Could someone please tell me how I can get my macbook to get off that stupid startup screen with the apple logo? It won't go past that screen and boot properly. I have tried reinstalling OS X didn't work. I tried running a disk utility test and no errors where found. I don't have the time machine thingy so I couldn't try that. Is there anything else I can do before taking it to Apple and l
paying hundreds of dollars???
thanks in advance!!!Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My Macbook pro is Start up with white screen without apple logo - stuck and can.t do any thing
Hi friends, I am stuck in my MacBook pro which shows white screen .
1- I tried hold C to Bogor from DVD to reinstall Mac os x , but it's not working .
2- I tried hold Shift and option to log to safe mode , but it's not working .
3 - I tried reset ram , but its not working .
Any advice ? I am stuck and can't do anything :(
RegardsIt would be helpful to know which MBP you have and which OS you're running.
Read the following and try the advice listed here: http://support.apple.com/kb/TS2570
Ditto: http://support.apple.com/kb/TS4088?viewlocale=en_US
Also, some things which cause a gray/white screen cause it to take much longer doing anything, so you may want to try some of your previous efforts and wait 5 minutes or so after each. -
MacPro doesn't start and stays on white screen with apple logo.
My mac pro does not start. It turns on because I hear the sound, Then the apple logo and progress bar appears. The progress bar does not load fully. I have done all the troubleshooting that is to be done including disk verification, disk repair, single user mode, set SMC and VPRAM. Nothing has helped. I have not backed up my files.
Hello ashmifromnolensville,
Welcome to the Apple Support Communities!
I understand that your Mac is only starting up to a grey screen with the Apple logo. I don’t want to have you complete troubleshooting steps that you have already completed, but for completeness sake, I would advise reading over the attached article and completing any suggested troubleshooting steps that you have not completed.
Mac OS X: Gray screen appears during startup - Apple Support
Have a great day,
Joe -
My MacBook Pro is stuck on grey loading screen with apple logo and spinning wheel.
PLEASE HELP - Tried to start up my MacBook Pro and I get grey screen w/ apple logo & spinning wheel. It's stuck on this screen. Safe mode didn't help but reveled this: smc read key action error, BOOS key failed, BOPS key failed. Consider rebuild of prelinked kernal com.apple.kext triggers triggered rebuild. IOBluetooth host controller USB transport Suspend Device. I ran verifications/repairs in Disk Utilities, but nothing came back wrong on the reports. I'm a bit panicked, as I use this computer for work and have no other computer to use in the meantime. I should also note that I have very little technical knowledge, so if you can lend your help please keep that in mind when responding. I'd be over the moon if anyone can help.
Startup - Gray, Blue or White screen at boot, w/spinner/progress bar
Startup - Gray Screen
Startup Issues - Resolve
Startup Issues - Resolve (2) -
My daughter's old I Mac won't start. It is not backed up. We want to get some things off of it if we can.
When we turn it on, we get the Apple logo with spinning wheel for awhile, then a question mark briefly and then a sky blue blank screen. Is there any hope of getting this to work? This computer is out of warranty. Does it seem that if we reinstall the Operating System we might find old data?First try restarting with the original install disc an run Disk Utility to repair the drive. If you have to re install the OS make sure you select archive and install or else everything will be lost.
-
is anbody there how does this work never done it before my macbook won't start past white screen with apple logo any ideas ?
Are you using a 10.6 Snow Leopard Install DVD? If yes, you can erase and install following these directions: http://support.apple.com/kb/HT3910
You'll know whether or not it is a hard drive issue when you get to step 8 under "Part One: Erasing the hard drive". If you do not see your hard drive in the list on the left side of the Disk Utility window then you know the Mac isn't seeing it—could be a loose cable, but more likely hard drive failure.
If you can see it on the left, click on it and look at the bottom of the Disk Utility window. If you see something like "S.M.A.R.T status: failing" that is definitely a hard drive issue. Otherwise, you can just follow the directions for an erase and install!
Might be worth fixing depending how much a repair would cost. Genius Bar could at least diagnose it for you and give a repair estimate. I'd look at what a new or refurbished one with your same specs would cost though to see if the price differential is worth it... -
MacBook Pro White screen, No apple logo, No question mark
Hi guys
I've MacBook pro 13 2010 model
The Laptop turn on all the time when i press power button
but It's stuck in white screen ( without apple logo ) . With hard drive connected or no hard drive i still can't see the question mark folder
What i've done
- Reset NVRM ( shift + Command+ option + power ) and it worked as i can see light changed in the charger
- I removed the hard drive put new one, then again removed hard from the board but no luck
- connected the Laptop to a monitor but not even showing video in the external monitor
Why can't i press PRAM button. NVRM work OK but not PRAM ( Option + Apple logo + P + R )
so keyboard is fineaskmeplz82,
if you’re unable to boot into Mountain Lion’s Recovery mode, then that limits your self-help options. These options still remain:
Do you still have the two grey installation DVDs which originally came in the box with your MacBook Pro?
Do you have a bootable external disk?
Do you have access to a FireWire cable and access to a second Mac with a FireWire port?
Do you have a spare SATA disk which can be temporarily installed inside of your MacBook Pro?
If the answer to all of these is no, then your only remaining option is to make an appointment at an Apple store or other qualified service facility so that they can diagnose/repair your MacBook Pro. -
i bought iphone 5s 2 days ago and suddenly it turn off and start again till the white screen with apple logo and start again
please answer me as soon as possibleHello Ahmedabokamar,
Thanks for the question! I'd recommend taking a look at the following article for troubleshooting steps that can help get your iPhone working again.
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Cheers,
Allen -
Won't turn on white screen with apple logo and spinning disc
Mac book air won't boot up just has a white screen with apple logo and spinning disc have tried all the startup multiple key pushes , I think
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Each time i press the power button i just have a blank white screen, and intermittent sounds/tone. No apple logo, or spinning circle.
I used to install the rEFIt to boot with win7. When I deleted win7, I didn't uninstall rEFIt. Nothing wrong with it. One day after I watched movie in full screen,I pressed esc to quit. Then I found the touchpad didn't work. I can't turn off air. I just pressed power button for a little while. It rebooted, then my nightmare just began...
I have tried everything, PRAM, command+R, literally everything. No change.
But when I plug a CD-ROM with USB, I can only here one BONG, just once, then white screen, Like waiting for something...
I took it to a service center in China, they told me the CPU had broken. SInce it's one month out of warranty, they wanted to charge me for like $250....
I really don't think that's CPU's problem. I checked the history, it seems like somebody else also had the problem before.
Can anyone give me some hints??? Thanks!!!!!! Or I have to take it back to America to check....Impossible, there are zero, as in none, zip, nadda viruses for OS X. If you have viruses on it they are for MS Windows and will not affect OS X. I suspect the hard disk has crashed, if you have backup then it's not a big deal to have it changed, just take it into your local Apple Store or AASP for service. If you have not been backing it up you may be in for a painful lesson on why backup is critical.
Maybe you are looking for
-
WSRP: Relative URL results in error code 404 in the consumer access.log
Hello everyone, I deployed a JSF portlet(implemented in facelets) in Weblogic Server 10.3.2 (11g) [extended to support WSRP]. When the JSF portlet is consumed from a 'consumer' portal [Weblogic 10.3.2 portal], WSRP URL Rewrite results in error code 4
-
Adobe LiveCycle ES Certification
Hi ALL Is there any certification for Adobe Livecycle ES product.Since I did not find a appropriate type I have posted it here ~Amol
-
I have been using Firefox and its ancestors since the beginning. I am at the end of my rope with it. When I click a link or open the browser it is because that is what I seek to have happen. Unless there is a way to turn off automatic updating, I am
-
Block Cancel release PR after creation RFQ & PR
Hi Gurus, I have created a PR. I have set my PR releae at header level. Then I have released PR items. After release, I have created RFQ & PO for that PR. Now after RFQ & PO creation, system allows me to cancel the releasePR . msg 076 is not usful f
-
10.4.3 breaks nfs gcc on client
I am doing embedded development on an arm 9 board running Debian 3. I have the debian root nfsroot served from a PB G4 17" with 10.4.3 This setup worked in OS X 10.4.2. After the upgrade to 10.4.3 it no longer works. The bug is a subtle one. If I com