My movie is out of sync after I export to Apple TV

Using imovie 11 V 9.0.1, my movie is properly synced in iMovie, no problems at all. But as soon as I export it to Apple TV or Quicktime etcc, it goes out of sync. It's really annoying especially because I have no clue what causes the problem. The movie is 13 minutes long so it shouldn't be a problem of length of the movie. Please help.

Is it 50p or 50i?
What make.model canera shot the footage?
Was the audio recorded to the camera or by a separate recorder?
Russ

Similar Messages

  • FCP 7.0.2 - audio and video out of sync after QT export! HELP!

    I loaded a self-contained movie of my project and exported it through Compressor. However, half way through the video, the audio and video went out of sync.
    This has never happened before — only since I upgraded to 10.6.3 and FCP 7.0.2/Compressor 3.5.2
    HELP!

    (P.S. I did change the Settings of the FCP from 720p60 to 720p30 about half way through the project, but that shouldn't affect the export.)
    About the time you changed FCP Easy Setup from 720p60 to 720p30 DURING Export?
    As you stated on this post:
    http://discussions.apple.com/thread.jspa?threadID=2384569&tstart=0
    I wouldn't think that's the best time to make a major change.

  • Audio out of sync after exporting into Quicktime using current settings.

    Quicktime file has audio out of sync when I export to quicktime movie using current settings.
    Ok for about the first few minutes then, out of sync after about 10 minutes.
    I shot the footage on tape with my Sony HVR-Z7u.
    My Sequence setting is the same as the format of the footage as shown below.
    Pixel Aspect Ratio: HD 1440x1080
    Editing Time base: 23.98
    Quicktime video settings: Compressor: HDV 1080p24
    Audio Settings: Rate 48 KHz
    Depth: 16bit
    Clip format:
    Pixel Aspect Ratio: HD 1440x1080
    Vid Rate: 23.98
    Compressor: HDV 1080p24
    Audio Rate 48 KHz
    Audio Format: 16bit

    I recently moved and both of my editing machines were unplugged for a couple of days until I could get them set up. After turning them back on, the problem had disappeared. Perhaps leaving the system unplugged had allowed some of the internal components to reset? That's the only thing I can think of. At any rate, the issue is gone.

  • Mac OS X partition ("Macintosh HD") gets out of sync after hibernation

    Hello,
    I have a first-generation Unibody 15" MacBook Pro. I run Mac OS X Lion and Windows XP Profession 32-bit through Boot Camp on it.
    I notice that the Mac OS X partition gets out of sync after I hibernate in Windows XP, reboot into Mac OS X Lion, restart and resume Windows XP. Certain folders would remain visible in Windows Explorer but become inaccessible, while some folders that I just created in Mac OS X would not even show up.
    Is there a way to tell Windows XP to "remount" the HFS+ partition?
    Steps to reproduce:
    Boot into Windows XP;
    Hibernate Windows XP;
    Boot into Mac OS X;
    Pick a folder and change something in it;
    Create a new folder;
    Reboot and resume Windows XP;
    Open "Windows Explorer";
    Try to access the folders you just meddled with.

    SwordAngel wrote:
    Hello,
    I have a first-generation Unibody 15" MacBook Pro. I run Mac OS X Lion and Windows XP Profession 32-bit through Boot Camp on it.
    I notice that the Mac OS X partition gets out of sync after I hibernate in Windows XP, reboot into Mac OS X Lion, restart and resume Windows XP. Certain folders would remain visible in Windows Explorer but become inaccessible, while some folders that I just created in Mac OS X would not even show up.
    Is there a way to tell Windows XP to "remount" the HFS+ partition?
    Steps to reproduce:
    Boot into Windows XP;
    Hibernate Windows XP;
    Boot into Mac OS X;
    Pick a folder and change something in it;
    Create a new folder;
    Reboot and resume Windows XP;
    Open "Windows Explorer";
    Try to access the folders you just meddled with.
    Don't hibernate, shut XP down when you reboot and the issue goes away, you really should consider using a more modern operating system.

  • Hi we setup ISE in our lab. We have 2 PSN registered but one of the node is out of sync after I upgraded form 1.1 to 1.2

    Hi we setup ISE in our lab. We have 2 PSN registered but one of the node is out of sync after I upgraded form 1.1 to 1.2

    For out of sync issues, which most likely are due to time changes or NTP sync issues, you must correct the system time and perform a manual sync up through the UI.
    For certificate expiry issues, you must install a valid certificate and perform a manual sync up through the UI.
    For a node that has been down for more than six hours, you must restart the node, check for connectivity issues, and perform a manual sync up through the UI.

  • My audio goes out of sync after import

    I have a bunch of masters of 1h documentaries that I've done using Adobe Premiere CS6. I've exported the masters using exactly the same specs:
    Apple Pro Res 422 (HQ), 23.98fps, 1920x1080p, 48kHz, 16b, PCM audio.
    I have to do some changes on the masters of these shows. They all play fine on several players like VLC, Quicktime, Mpeg Streamclip, etc. However after I import the masters into Premiere Pro CC, 3 out of 10 shows get the audio gradually out of sync, even on the source monitor before I put them on a timeline. The behaviour continues even after I place them on a timeline.
    The project settings are the same as the masters and so are the sequence settings. I've tried to recreate the project, delete and re-import, duplicate the file and import that, and no matter what I do the same 3 masters go out of sync after the import.
    I've tried to find a solution in many forums and despite noticing that several people have the same issue, no one has a valid solution for my problem.
    I cannot go back to CS6 since my company updated their systems to CS7 so I can't even cross check.
    Any suggestion will be most welcome.
    Thanks in advance peeps.
    NJ

    Couple of suggestions.
    First, rather than opening the Master export, go back to the original project.  That should open fine in CC.
    Second, with a CC subscription, you do have access to the full CS6 suite.

  • Audio out of sync after importing .MOV

    Experiencing audio out-of-sync issues after importing a .mov clip into Premiere Pro.
    The .mov clip causing the problem does not have a problem when played with quicktime or vlc: The audio matches the video perfectly.
    Adobe Premiere Pro CC 7.2.1 (4) on OSX 10.9.1
    Open Premiere, New Project ... > OK > Import the single video clip (whether by dragging into the app, or using the Media Browser). Start playing the clip in the Source monitor, scrub forward. Result: audio and video are way out of sync.
    The .mov clip causing the problem was exported from Silverback app.  http://silverbackapp.com/
    Details about the .mov clip, via Media Inspector app:
    ============================================================
    General
    Complete name                    : /Users/jukeboxhero/20140203.mov
    Format                           : MPEG-4
    Format profile                   : QuickTime
    Codec ID                         : qt 
    File size                        : 638 MiB
    Duration                         : 34mn 46s
    Overall bit rate                 : 2 566 Kbps
    Encoded date                     : UTC 2014-02-04 06:52:45
    Tagged date                      : UTC 2014-02-06 15:55:40
    Writing library                  : Apple QuickTime
    Video
    ID                               : 2
    Format                           : AVC
    Format/Info                      : Advanced Video Codec
    Format profile                   : [email protected]
    Format settings, CABAC           : No
    Format settings, ReFrames        : 2 frames
    Format settings, GOP             : M=2, N=30
    Codec ID                         : avc1
    Codec ID/Info                    : Advanced Video Coding
    Duration                         : 34mn 46s
    Bit rate mode                    : Variable
    Bit rate                         : 2 449 Kbps
    Width                            : 1 920 pixels
    Height                           : 1 080 pixels
    Display aspect ratio             : 16:9
    Frame rate mode                  : Variable
    Frame rate                       : 18.969 fps
    Minimum frame rate               : 6.522 fps
    Maximum frame rate               : 19.355 fps
    Color space                      : YUV
    Chroma subsampling               : 4:2:0
    Bit depth                        : 8 bits
    Scan type                        : Progressive
    Bits/(Pixel*Frame)               : 0.062
    Stream size                      : 609 MiB (95%)
    Language                         : English
    Encoded date                     : UTC 2014-02-04 06:52:46
    Tagged date                      : UTC 2014-02-04 15:27:35
    Color primaries                  : BT.709-5, BT.1361, IEC 61966-2-4, SMPTE RP177
    Transfer characteristics         : BT.709-5, BT.1361
    Matrix coefficients              : BT.709-5, BT.1361, IEC 61966-2-4 709, SMPTE RP177
    Audio
    ID                               : 1
    Format                           : AAC
    Format/Info                      : Advanced Audio Codec
    Format profile                   : LC
    Codec ID                         : 40
    Duration                         : 34mn 45s
    Bit rate mode                    : Constant
    Bit rate                         : 104 Kbps
    Nominal bit rate                 : 128 Kbps
    Channel(s)                       : 2 channels
    Channel positions                : Front: L R
    Sampling rate                    : 44.1 KHz
    Compression mode                 : Lossy
    Stream size                      : 25.9 MiB (4%)
    Language                         : English
    Encoded date                     : UTC 2014-02-04 06:52:45
    Tagged date                      : UTC 2014-02-04 15:27:35
    ============================================================
    The video imports perfectly into Final Cut Pro 10.1.1
    I have Premiere Pro trial and Final Cut Pro trial. If there's no fix or easy work-around, I will have to ditch Premiere.

    >Frame rate mode                  : Variable
    No version of Premiere does "well" with Variable Frame Rate
    Below is about iphone, but may help
    Some people find that Iphone won't edit easily because it uses a variable frame rate
    - A possible fix in message #22 http://forums.adobe.com/thread/934466

  • Audio out of sync after converting flv to mov

    Hi all,
    Mission - I need to convert an .flv file to .mov in order to edit in FCP and export out again as flv file
    Process - open flv in mpeg streamclip, export as quicktime mov.
    Problem - when importing to fcp, the audio is out of sync. It may be in sync in one place but out in another. Seems like its a different frame rate???
    What am I doing wrong? How can I fix this?? It's needed tomorrow morning.
    Urgent help is appreciated.

    No response yet. Anybody have any ideas on this please?

  • Audio and video out of sync after exporting sequence

    I'm a FCP user since years, but not so common with HD footage. Therefore I have an issue with my finished edited movie after exporting: Video and Audio are out of sync.
    My sequence settings are: HDV1080i50, 25fps, 48kHz, 16bit, Stereo. I used File-> Export-> Quicktime Movie -> Current Settings
    Sequence has a duration of 61 minutes and 38 sec. I tried to find out where's the problem and exported audio and video seperated. This results in:
    Video is 61 minutes and 27 sec long
    Audio is 61 minutes and 38 sec long
    That means exported video is shorter than original sequence.
    What could that be ?

    I had the same problem with a Panasonic camera, even filming at 30 fps. I was able to fix it; see [this thread|http://discussions.apple.com/thread.jspa?threadID=1783029&tstart=0]. It's a frustating problem, to be sure. You might have to use Easy Setup a couple times before you get things to work properly. Not sure why that's the case.
    Good luck!
    Message was edited by: Anthony M Kassir MD

  • Captivate 6 editing - on timeline, audio is out of sync after pausing

    I am trying to create a software demo for my company. I am using the HD video and then have imported audio recordings over the video.
    The big work portion of this project is adding call-out smart shapes on the video during certain portions to highlight what the voiceover is discussing. However, when I pause the timeline so I can add a smart shape, upon resuming from the pause, the audio is out of sync. This happens even if I hit Stop on the timeline, and use my mouse to move the playhead.
    This is adding significant amounts of time to my video editing process, to the point where I am missing deadlines for having the videos created. The only solution I have found to guarantee that the call-out smart shapes are in sync with the audio instructions is to Play the timeline from the very beginning, each time after pausing the audio.
    Is anyone else experiencing these issues, or know of a way to fix it? This is adding enough time to the editing process that our company is looking into other video editing softwares to replace Captivate.

    I always copy the entire PRIVATE folder from camera to hard drive, and then importing from that hard drive folder in to project.
    I am saing original, becouse I do not convert them to diferent format. And how could be the original files of video and  audio out of sync???
    I am using Premiere for 10 years, I am not new to this software, but never had this problem.

  • Rented HD Movie Audio out of sync

    have itunes on a win 8 pc. latest vesrion of ITunes , rented an HD movie and the audio was horribly out of sync. tried stopping starting and restarting but it always moved farther out of sync. Any fixes for this problem other than not to rent movies?

    Let's see if some of these questions might bring to light your issue:
    1) Reference movie or self-contained?
    reference, though I am burning a self-contained version just to see
    2) Is this audio you've added/adjusted yourself... I mean, did you have to sync it yourself in the timeline as you were editing?
    interviews - SOT and music no specific to clips
    3) Are there any 'holes' in your audio on the timeline... spaces as it where?
    no holes
    4) Would there be, by chance, a change in what ends up monitoring the audio from you watching the timeline in FCP to when you open it in Quicktime?
    5) Have you loaded the reference movie back into FCP to see if indeed it is out of sync there too?
    Reference movie is out in FCP but the timeline is fine.
    6) This 'jump'... obvious jump? Slight shift over time? Same place every time? Tied to an edit maybe?
    obvious jump that shifted position after I tossed the preference file.
    7) What are your computer specs?
    Did you need something more specific than the specs I posted in the question? Otherwise, Dual Core Intel 2.66 GHz Mac OS X (10.4.10) 4 Gb ram 1 hour video FCP 6.0.1
    Thanks for the assist, Capt.

  • Why is Audio out of sync after encoding?

    I have encoded a 60 minute film using separate video and audio files -- quicktime for picture, AIFF for audio. In the DVD Studio Pro project, they are perfectly in sync. But in the encoded DVD they are playing out of sync by over 1 second.
    I've encoded the same movie with different versions of the soundtrack several times before with no problems.
    Anyone have any ideas of what has happened and how to fix it?
    The Quicktime and the AIFF were on different drives when I was building the project. Could this have had any effect?
    Using DVD studio pro v4.0.2
    Powerbook G4   Mac OS X (10.3.9)  

    Nope, I am a strong believer if it ain't broke do not fix it, and personally I loved 10.3.9 - in fact I say away from updates unless absolutely needed and then I bring them onto different machines. Unless something changed in your system, I would try standrad troubleshooting (repair permissions and delete prefs) and A.Pack the audio
    Not to say I do not have machines running Tiger, but Tiger (particularly some of the newer versions) I find to be a PITA - around 10.4.6 or so there are weird security things happening which messes up installing software. In fact I just zeroed out my tiBook, and did not add some software that I forgot about until after 10.4.8 was on and it does not install. I would have to zero things out again. Install the software over 10.4.1 and then try again.
    Unless you want the Universal Suite (which is good for most things except DVD SP which has issues) nope, no Tiger none of the new stuff, unless you have a few machines to play with

  • Audio out of sync after bring in from iPhoto

    I designed a 644 image slides show in iPhoto and the made the mistake of bring it into iDVD. After talking here in Apple Discussion I was told to build it in iPhoto and bring it into iMovie that way at each 98th imaged it wouldn't stall as it did in iDVD. I had it all synced up in iDVD the way I wanted it. After going back and building a slide show in iPhoto with the audio and making a quick Time movie I brought it into iMovie and preview it and the sound is off by 3 images. The sound is coming in 3 images late. So I tried again in iPhoto to build a quick time movie without audio so then in iMovie I could hopefully edit the audio to match what I want but even if I check the box in iPhoto for "no audio" it still comes with it. Should I just forget about the quick time movie out of iPhoto and drag all the images into iMovie and go from there? And is quick time the right thing to render to for viewing on HDTV?

    Hi Meg The Dog,
    Thanks for your helpful response.
    Please see two images below -- Properties 1 and Properties 2 screengrab. Below that is a screen shot of the sequence settings. My edit system is confiigured thusly (I *think*): I ingest the tape into FC7 via Log & Capture, from using a Sony XDCAM reader. I store the ingested media on data drive just for video, in my tower. Please let me know if this information was helpful and what else I might need to do! --Paolo

  • Voice and Video out of sync after burn in iDVD

    We are having trouble keeping the voices and movement together after a burn. Can anyone give us a suggestion?

    Barbara and Amy
    You may have experienced what many of us have encountered. Cameras are usually set to record in 12 bit audio. When these recordings reach iMovie they edit and play fine but when they go on iDVD the sound is out of sync.
    Switch your camera to 16-bit in future to prevent/minimise the effect.
    You should also look at a couple of apple pages http://docs.info.apple.com/article.html?artnum=42974 and http://docs.info.apple.com/article.html?artnum=61636
    Also there is some good information on
    http://www.danslagle.com/mac/iMovie/audio/1001.shtml

  • Movie audio out of sync

    Is there a fix for PC users running iTunes? When attempting to play movies the audio is out of sync.

    Let's see if some of these questions might bring to light your issue:
    1) Reference movie or self-contained?
    reference, though I am burning a self-contained version just to see
    2) Is this audio you've added/adjusted yourself... I mean, did you have to sync it yourself in the timeline as you were editing?
    interviews - SOT and music no specific to clips
    3) Are there any 'holes' in your audio on the timeline... spaces as it where?
    no holes
    4) Would there be, by chance, a change in what ends up monitoring the audio from you watching the timeline in FCP to when you open it in Quicktime?
    5) Have you loaded the reference movie back into FCP to see if indeed it is out of sync there too?
    Reference movie is out in FCP but the timeline is fine.
    6) This 'jump'... obvious jump? Slight shift over time? Same place every time? Tied to an edit maybe?
    obvious jump that shifted position after I tossed the preference file.
    7) What are your computer specs?
    Did you need something more specific than the specs I posted in the question? Otherwise, Dual Core Intel 2.66 GHz Mac OS X (10.4.10) 4 Gb ram 1 hour video FCP 6.0.1
    Thanks for the assist, Capt.

Maybe you are looking for