My nano goes to sleep after removing the charger when fully charged

After around 3 years I start to use my ipod again. It can charge perfectly fine but when I removed the charger when it's fully charged, it goes to sleep. I can't turn it on afterwards. Is it not working because the battery is "dead"?  I can do everything just fine but I can't use it unless it's charging.

Considering that the iPod wasn't used for 3 years, it's likely that the battery is dead and in need of replacement.  You can have Apple service it for a flat fee or you can send it into a 3rd party repair company for a little less.
B-rock

Similar Messages

  • After Removing The Charger, PC Gets Overheated

    I have an hp pavilion dv6-3050tx, Running Windows-7 64 bit. Few days back I had changed my battery as my earlier battery was not able to provide backup more than 5min. But after inserting the new battery I am facing a problem.
    As soon as I unplug the charger. The system temperature increases exponentially and soon after that the PC gets into Hibernation.
    It happens only when the pc is running over battery. While after connecting the charger system temperature again comes to normal.
    Plz Help me out with it…

    Hi,
    Please do not worry.
    Please download and install the BIOS Update from the following link: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100446-1&cc=in&dlc=en&lc=en...
    Important instructions for installing the BIOS update
    Once you have downloaded and saved the latest version of the BIOS to your computer, you will need to install it. It will take a few minutes to install the BIOS update. It is important to remain patient - do not interrupt the process, and allow the updates to install properly.
    To install the BIOS update, be sure that you are running on AC, not battery, power, and follow the steps below.
    1. Connect the AC power supply to the computer. 
    2. Before installing the BIOS update, close any open programs and temporarily disable your antivirus software. Remember to re-enable the antivirus software after the installation is complete.
    3. Locate the BIOS file (sample name: sp45070.exe) that you downloaded to a convenient location on your computer.
    4. Double-click the file to start the installation and follow the on-screen instructions.
    5. When you are asked for BIOS version you don't have to enter the version number, instead you can continue with the installation by clicking the "Next" or the "Continue" button.
    5. Allow the installation to complete all of its actions, and then restart the computer when prompted.
    The latest version of the BIOS is now installed on the computer.
    I hope that helps.
    !------------------- Please click the KUDOS star on the left to say 'Thanks'. Please mark 'Accept as Solution' if it answers/solves your problem. Thank you-----------------------------------------------------------------!
    I am an HP Employee. 

  • Hi when I stream video content to my Tv using Apple from my Ipad3 I find the Ipad goes to sleep after 2/3 minutes and disconects, the only way I have found to stop this is to continually tap the Ipad screen but there has to be a simpler method/ any help

    Hi when I stream video content to my Tv using Apple tv from my Ipad3 I find the Ipad goes to sleep after 2/3 minutes and disconects, the only way I have found to stop this is to continually tap the Ipad screen but there has to be a simpler method/ any help would be most welcome.

    Welcome to the Apple Community.
    Contact the developer of the Air Video app.

  • HT1776 I have the Energy Saver setting set to NEVER on both options, and my computer STILL goes to SLEEP after 1 hour. Please help!

    I have the Energy Saver setting set to NEVER on both, and my computer STILL goes to SLEEP after 1 hour. Please help!
    My COMPUTER goes to sleep and disrupts my apple tv all the time. How can I fix this?

    That you are getting the BONG is a good sign, it's unlikely to be hardware if you are able to hear that.
    Start by running SW update. It's not that there is a specific fix, but when updating it may rewrite some system files which may get this going again purely as a side affect. Worth a go, and should not harm the system.
    Try reset the PRAM - Resetting your Mac's PRAM and NVRAM
    Hopefully one of these quick fixes works, otherwise we'll need to try isolate the issue next - so if still having a problem, I'd try create a new user and login as that user to see if the issue persists (which will tell us if it's system wide or user specific)

  • HP pavilion/dm4 goes to sleep after 1 minute--it's a drag!

    I've checked my control panel settings and then the advanced settings (for notification icons--which doesn't apply to this problem).
    What ever I set, I'm working at my computer and screen always goes to sleep 1 minute after if I don't touch the keyboard.
    What am I not getting. I need at least 5 minutes or so before it should go to sleep. My computer at the office only goes to sleep after I make it.
    Thanks.
    Doug
    This question was solved.
    View Solution.

    THANK YOU! I'M GLAD IT WAS SOMETHING SIMPLE.

  • I have a Ipad 2 w/ iOS 7 it goes to sleep after about 2-3 minutes.Why?

    I have a Ipad 2 w/ iOS 7 it goes to sleep after about 2-3 minutes.Why?

    If it's been inactive and you have it set in settings to shut down after a certain period of time, it will.
    Try going into settings and changing this to your preference. If this is not the issue, adjust the settings anyways, then put back how you prefer. Sometimes  turning a setting off, then back on can help
    Aside from this you can do a restart. Press and hold the home and sleep button at same time until the apple logo appears. Or in settings > Reset> Reset all.

  • I am trying to download mountain lion but the pc goes to sleep and stops the download even though I have set my power defaults to 3 hours

    I am trying to download mountain lion but the pc goes to sleep and stops the download even though I have set my power defaults to 3 hours

    aldofromwilts wrote:
    I am trying to download mountain lion but the pc goes to sleep and stops the download even though I have set my power defaults to 3 hours
    Try setting the Energy Saver to "never" and uncheck "put hard disks to sleep when possible". You can allow the screen to sleep after any suitable time.
    Hope that helps. Regards.

  • Powercfg sets power plan with never sleep but system goes to sleep and locks the screen

    I created a command (.bat) file that executes 'Powercfg -s 8c5e7fda-e8bf-4a96-9a85-a6e23a8c635c' where '8c5e7fda-e8bf-4a96-9a85-a6e23a8c635c' is the class name for power option (HighPerf) that sets sleep to never. Then I created a scheduler's task to execute
    this command file at specified time. The goal here is to switch at this time from power option that has sleep in 1 hour (Balanced) to the power option that never sleeps.
    At the designated time the power option changes from Balanced to HighPerf but after some time computer both goes to sleep and locks the screen. I do not know whether this happens at the same time or not. It is just that when I get to my computer some time
    (2 hours) later, it is in the sleep mode (the light on the power button is amber), I need to press the power button to wake it up and when it comes to life I find out that the screen is locked and I need to enter the password.When I open Control Panel it shows
    that HighPerf power option is selected. Yet, the computer went to sleep and the screen got locked.
    All this does not happen when I set HighPerf power option from the Control Panel.
    I am using Dell XPS 8500 desktop with Windows 7 Home Premium, so battery and closed lid settings do not apply as they do not exist on this computer, so those settings are not at issue.
    Thank you
    Isa Ten

    Hi Isa,
    Based on your goal "The goal here is to switch at this time from power option that has sleep in 1 hour (Balanced) to the power option that never sleeps.", why didn't you set the Balanced option to never sleep?
    If you just ant it at one time to switch, you need another task to change back. Otherwise, it keep "never sleep" and "high perf"status.
    Meanwhille, check your hibernate status of these power plan under sleep tab:
    Power Options->Change Plan Settings->Change Advanced settings, you see a tap "Sleep"
    Karen Hu
    TechNet Community Support

  • How do I cancel a Newsstand subscription when there is no auto-renew facility/option through Settings? After removing the item on Newsstand it still shows as Active in Store Settings/Manage Subscriptions.

    How do I cancel a Newsstand subscription when there is no auto-renew option via Settings/Manage Subscriptions? After removing the item from the Newsstand site it still shows as Active via Settings/Manage Subscriptions. The publisher tells me it is not a subscription rate that is theirs, they have no knowledge of it, I subscribed through iTunes Store. Thank you!

    Hi qwerty,
    Dun tink that creative customer support sucks cos I had been dealing with them in the past and I can say that their service are quite gd and fast. If you wanted a refund, I tink you need to contact the store that sells you the product. Dun tink creative will refund you though.

  • Table disabled after removing the last record

    After removing the last row of table and disables it is unable to select any record.
    Version: JDeveloper 11.1.1.2.0

    Problem solution
    my backBean:
    protected void limpaSelecaoDaTabela() {
    if (usaPopup)
    if (table != null)
    table.setSelectedRowKeys(null);
    protected void limpaSelecaoDaTabela() {
    if (usaPopup)
    if (table != null)
    table.getSelectedRowKeys().removeAll();
    }

  • I cannot log in my account but can as a guest even after removing the password

    i cannot log in my account but can as a guest even after removing the password

    Hi Kabiru,
    Thanks for visiting Apple Support Communities.
    You may want to use the steps in this article to reset your user account password:
    OS X: Changing or resetting an account password
    http://support.apple.com/kb/HT1274
    Best,
    Jeremy

  • When my screen goes to sleep and then the hard drive goes to sleep why won't the screen wake up?

    I can repeat this 100% of the time.  If I let the screen go to sleep (or I manually put it to sleep) and I shut the computer so the hard drive goes to sleep (or if the hard drive simply goes to sleep on the timer), when I open the Macbook Pro the screen will not wake up, although I think the hard drive does as the back light on the keyboard turns on.  Any ideas on why this is happening.  My computer is 4 weeks old...a bit frustrating.  The best answer I have gotten is get a new one for Apple...or completely re-install the OS.
    Jared

    The reason why it's happening is not obvious and can't be determined without more information. The fact that you can reproduce the problem makes it a lot more tractable.
    As a first step, boot in safe mode (shift key down at startup.) Can you reproduce the problem now? If so, note the time, then reboot as usual (not in safe mode) and look in the system log for error messages at the time the screen failed to wake up.

  • I have an IPad 4.  After updating the system, when I try to look at picture on Facebook and make it larger, there is just a "circle" in the middle of the page instead of the picture.  Can anyone help me?

    I have an IPad 4.  After updating the system, when I try to look at picture on Facebook and make it larger, there is just a "circle" in the middle of the page instead of the picture.  Can anyone help me?

    Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
    Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)

  • HP OfficeJet Pro 8500 goes to sleep, but often wakes up when it shouldn't

    HP OfficeJet Pro 8500 goes to sleep, but often wakes up when it shouldn't.  This happens over and over.  It used to sleep until I sent something to be printed. I now shut the printer down, but that takes a long time to start it up.

     When you finally get around to looking at my post, never mind.
    I reset the factory defaults on the printer and reauthorized my WiFi network.
    Now it is working.

  • My imac g5 goes to sleep while in use. typically when im playing games

    For the last several months, my mac has been going to sleep during use. Typically when im playing games, like second life, or in any type of programs, but it has also been going to sleep while im watching videos on youtube or hulu. It's getting worse and worse, and once it goes to sleep the first time, it doesnt stay on long afterwards. When browsing the internet, its fine. I've recently backed up 40,000 images that I had on my computer, and deleted for more memory space. but it didnt stop it from going into sleep mode, it just doesnt go as quickly as it was before. I was told that it was a memory problem, but since i deleted all of the images off of my computer, the problem still persists. I even turned sleep mode to "never". Here are some of my computer stats:
    Memory: 512 MB
    Processor: 2.1 GHz PowerPC G5
    Space Free: 104.18 GB
    Space utilized: 128.58 GB
    My monitor stays warm, never gets hot, but sometimes i can hear the fan blowing loudly when it goes into sleep mode
    If anyone could help, i would greatly appreciate it =)
    Message was edited by: mswilliams
    Message was edited by: mswilliams

    The temps are a bit higher than I'd expect under normal circumstances, and too high while playing games, but what is the room temp where it is?
    I def. think its a temp thing now. but why does it only raise when im playing games or watching videos online?
    Games tipically press the CPU, Video Card, RAM, and everything else much harder than most apps.
    It may be a Fan not working properly, or just dust buildup.
    Boot off your Install Disk while holding down the *d key*, (not c key), then run the extended Apple Hardware Test. Some disks require you to use the Option key at bootup to select AHT. Some models have a separate AHT CD.
    Report any errors it finds.

Maybe you are looking for

  • Apple TV - with Adobe Lightroom or Photoshop Elements

    With Apple Aperture being phased out and iPhoto being replaced, are the adobe products a good alternative if you use Apple TV for much of your photo viewing?  Of the two Adobe products not sure which is the closest match to being an Aperture alternat

  • Safari won't open sometimes on startup

    Hi, over the last few days, safari hasn't been opening from the dock immediately after I have turned on my macbook, it just keeps jumping up and down and then I have to force quit it. Any idea why this might be happening? Thanks

  • How to export both masters and versions w/ metadata?

    When traveling I import photo files into Aperture on my laptop and edit them.  When I get home I would like to export "everything" - masters, versions, and metadata, so that I can then import all of this into Aperture on my desktop.  Or, perhaps ther

  • Multiple addresses for one contact in a Group

    I need to add a work address and a home address for ONE contact in my address book to a group. How can I do this without expanding the group and manually adding the other address? I don't want to have to expand the group. Thanks for any assistance.

  • Openoffice/abiword unicode font

    I'm trying to use a unicode font with openoffice/abiword for some translations to ancient Greek. I have a unicode font that I'd like to use, but the only way I can get Greek letters is by going to the "insert special characters"-dialog and insert one