My nano says connected- eject before disconnecting. how do i do this properly?ly

my nano says connected- eject before disconnecting. how do i do this properly?

Hi torquey 46,
If you are looking for more information on ejecting or safely disconnecting your iPod from your computer, you may find the following article helpful:
Apple Support: Safely disconnect iPod
http://support.apple.com/kb/ht1853
Regards,
- Brenden

Similar Messages

  • My nano says connected eject before disconnecting what does that mean

    I plugged my new iPod nano in a couple hours ago and it says "connected eject before disconnecting" what does that mean?

    Hi Yogibear2,
    Thanks for visiting Apple Support Communities.
    This article has some information on the topic:
    Safely disconnect iPod
    http://support.apple.com/kb/ht1853
    When iPod is connected to a computer there are times when it should not be disconnected by simply unplugging the USB cable. In these cases, iPod must first be ejected before it can be safely disconnected. Read the information in this article to determine when an iPod can be safely disconnected.
    Best,
    Jeremy

  • Hi everyone, I was wondering if someone can help me.  I recently got my first ever Ipod.  It's the new Ipod Nano 7th Generation.  I have tried to synchronise it with Itunes but it says "Connected, Eject before Disconnecting" but nothing happens.

    Hi everyone, I was wondering if someone can help me.  I recently got my first ever Ipod.  It's the new Ipod Nano 7th Generation.  I have tried to synchronise it with Itunes but it says "Connected, Eject before Disconnecting" but nothing happens.  I have tried uninstalling & re-installing Itunes but this didnt help. 
    Does anyone have any ideas? 
    Thanks for your help.

    I think the problem is that the iPod got set to Manually manage music and videos.  It needs to be set up for automatic syncing again.  Just unchecking that Manually manage music and videos setting does not do it.
    In iTunes 12, select the iPod in iTunes (using the device button), so that you see the iPod's "management" screen.  In the sidebar (along left side of screen), there are two headings (Settings and On My Device).  Under Settings, click on Music.  To the right, you see the iPod's Music screen, where you tell iTunes how to sync songs to the iPod.
    Check the box at the top for Sync Music.  That turns ON automatic syncing for music.  Below that, choose the option to sync Entire music library (assuming your music library fits completely on your iPod).  Otherwise, you can choose the option to sync Selected playlists, artists, albums, and genres and make your selections below.  Then click Apply.

  • I plugged my iPod into my computer to charge it up.  It says, Connected, eject before disconnecting.  how do I do that?

    I plugged my iPod into my computer to charge it up.  It says, Connected, eject before disconnecting.  how do I do that?

    See here: Safely disconnect iPod
    B-rock

  • IPOD froze now says "Connected Eject before disconnecting"

    Error connection came up-now ipod is locked saying Connected Eject before disconnecting. Computer does not recognize ipod. How can I unlock the ipod or get my computer to recognize it?

    Im also having this problem, it used to work fine, then one day just came up with this CONNECTED EJECT BEFORE DISCONNECTING message when USB plugged in and Itunes does not recognise the IPOD so I cant disconnect it.
    I have tried re-setting it (several times).
    Have tried downloading latest software
    Have tried letting battery run totally flat
    Tried re-booting computer
    Tried going into MY COMPUTER and ejecting from my devices but its frozen out
    Any help much appreciated as its new but totally useless now

  • IPod says connected,eject before disconnecting with a pict. Of the USB cable. It does this after its been charging and I can not access the menus. Any solutions?a

    iPod seems to be frozen. After it has been charing and I remove it foamy PC! It says "connected, eject before disconnecting" with a picture of the USC cable. I can not proceed with this on the screen. Should I reconnect to my pc and do something differently?

    Try to perform a hard reset of the iPod, which is about the equivalent of rebooting your PC.  To do this, first make sure the hold switch is in the Off position.  Then press and hold both the Select (Center) and Menu buttons together long enough for the Apple logo to appear.
    B-rock

  • Ipod is frozen, says "connected Eject before disconnecting"

    I have an 8 Gb ipod Nano and so far its been working really well.. but today i installed the "genius" feature, and it works on my itunes, but ever scince then my ipod has been frozen! The screen says "Connected". I tried everything The clock is even frozen!
    I'm super confused! I tried what they said to do on Apple.com but my computer just told me that the device was up to date... i have no clue what that means
    Someone please help me
    :))))

    i tryed shutting it off, plugging it back in and almost every...
    Almost every what? Have you tried resetting the iPod? See this.
    How to reset the iPod if it appears frozen or is not responding.
    It may take quite a few attempts and is best done connected to power.
    and also is there any way to get all ur phurchases back
    Every time you download music from the iTunes store Apple have to pay the artist royalties, so the official stance from Apple is that purchases from the iTunes music store can only be downloaded one time. Then, you must pay again.
    This is why you are prompted to back this music up to a cd or dvd.
    Some people say that they've been allowed a re-download for various reasons when they've contacted Apple.
    You can only ask but please be aware that Apple are not obligated to do this for you.
    iTunes store support.

  • IPod stuck on CONNECTED - EJECT BEFORE DISCONNECTING - How do I reset it?

    Title says it all. Thanks for your help.

    Toggle the hold switch off and on a few times then hold down the MENU and SELECT (centre) buttons for five or ten seconds until you see the Apple logo appear then the menu button to go to the normal display: How to reset an iPod

  • Anyones ipod get stuck in the connected eject before disconnecting mode

    My ipod is stuck on and says connected eject before disconnecting, it will not shut off.

    Have you tried resetting it?
    How to reset iPod
    B-rock

  • IPod nano 6th generation: "Do not disconnect" on white screen w/flashing icon; previously "Connected-Eject before Disconnecting" on dark screen w/USB icon; no content on iPod

    Trouble began with "Reconnect to iTunes to Restore" message after I inadvertantly held down the Wake/Sleep button long enough to turn the iPod off before pausing the podcast in progress.
    My subseqent actions to try to remedy:
    -Restored the iPod
         -while Restoring, the rotating circular arrows and "Synchronizing-Do Not Disconnect" screen appeared followed by "Connected-Eject Before Disconnecting"
         -when I ejected the iPod and disconnected it, the normal icons showed but there was no content
    -Reinstalled the latest iTunes 11.0.3 which I had downloaded previously a few days before my problems began
    -Restored iPod again:  still said "Connected-Eject before Disconnecting"
    -Manually put the iPod into Disk Mode (said to be helpful in troubleshooting):  "Do Not Disconnect" on white screen with flashing icon (circle with diagonal line)
    -Ejected and disconnected the iPod.
    -Reconnected the iPod:  same message

    You need to either the let the iPod finishing syncing with iTunes, or figure out what application is still using it in the back ground that prevents you from being able to properly eject the device.  Just unplugging it from the computer is almost always going to cause issues when it's still in use by iTunes or another application.
    So let's connect the device to iTunes one more time and let it finish restoring.  Then try syncing a bit of content over to it and wait for it to finish the sync process.  Then try to properly eject it from iTunes this time.
    B-rock

  • Ever since the new update, my Ipod won't sync. Starts to sync but then goes back to connected eject before disconnecting. Still won't transfer songs even after being restored. Restored fine. But now I've got nothing on it. Please god help!

    For awhile, since the newest update, I'd noticed when charging the ipod (classic) that it stopped going to the charging screen and would stay on the  Connected: Eject before disconnecting' screen. But, y'know, didn't matter to me, it still charged... until today when I tried to add music. Tried it many times, reset it... STILL wouldn't transfer songs... It would 'say' it was syncing, but then suddenly stop and stay on the same Connect: please eject before disconnecting' page. I did a couple of times get a message about scanning it but, after restoring that never popped up again...
    So, I do a system restore on it and ofcourse THAT works, but it STILL won't sync! So, now I've got an ipod with no music that won't sync and because it's all gone on there, I'm not sure how to back up my stuff (should I need to re-install iTunes... Though I doubt it'd work...)... So, yeah, I tried a different cable too, still no luck...
    There has GOT to be some way to fix this!
    Please somebody help me out! I so freaking appreciate it you have NO idea!

    I think the problem is that the iPod got set to Manually manage music and videos.  It needs to be set up for automatic syncing again.  Just unchecking that Manually manage music and videos setting does not do it.
    In iTunes 12, select the iPod in iTunes (using the device button), so that you see the iPod's "management" screen.  In the sidebar (along left side of screen), there are two headings (Settings and On My Device).  Under Settings, click on Music.  To the right, you see the iPod's Music screen, where you tell iTunes how to sync songs to the iPod.
    Check the box at the top for Sync Music.  That turns ON automatic syncing for music.  Below that, choose the option to sync Entire music library (assuming your music library fits completely on your iPod).  Otherwise, you can choose the option to sync Selected playlists, artists, albums, and genres and make your selections below.  Then click Apply.

  • Connected, eject before disconnecting

    My 3g nano wouldn't show up on my itunes or explorer, but i got the "Connected, Eject before disconnecting" I turn puter off and nano stll says this. I unplug nano while puter is off and nano still says this. I use external power source and same issues. My nano is stuck on this screen and a "locked" icon appears even though it's fiscally unlocked. what gives?

    Well start with these articles and see if that gets you anywhere...
    iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
    http://docs.info.apple.com/article.html?artnum=305136
    iTunes for Windows: iTunes 7 doesn't recognize iPod
    http://docs.info.apple.com/article.html?artnum=304434
    iPod missing in "My Computer" or in iTunes for Windows
    http://docs.info.apple.com/article.html?artnum=61711
    Also you might try forcing the iPod into disk mode first, then connecting it to your computer and see if that makes it show up in iTunes...
    Putting iPod into Disk Mode
    http://docs.info.apple.com/article.html?artnum=93651
    Windows confuses iPod with network drive or hard drive and may keep iPod from mounting or songs may seem to disappear
    http://support.apple.com/kb/TS1493
    Patrick

  • 160 GB frozen "connected--eject before disconnecting"

    When I tried to sync my 160GB iPod to iTunes (v.7.5) it froze with message "Connected--Eject Before Disconnecting." It did NOT show up either on my desktop or in iTunes. I tried restarting computer, but computer would not restart. Finally, I disconnected the iPod but the screen was still frozen. I was then able to restart computer and re-attach iPod but iPod is still frozen with same message. Any help appreciated.

    I've had an interesting and perhaps relevant experience recently. I was getting messages that my iPod was corrupted or alternately it failed to show up. I called tech support and they couldn't figure out what was happening. I also noted that Time Machine was running very slowly. In checking on this I noted that Windows security software could do this. It occurred to me that I should turn off the anti-virus and anti-spyware software on the Windows side of my computer. Once I did this everything returned to normal with my iPod. I have no clue as to how the Windows based software is affecting my Leopard based performance but it is. Perhaps someone can explain how and why this is happening and perhaps there is some solution as it means switching to Windows will involve extra work turning on the security when I enter and turning it off when I leave.

  • What does it mean when it says to eject before disconnecting Ipod?

    What does it mean when it says to eject before disconnecting Ipod?

    When you press the eject button, iTunes checks to make sure if it has finished using the iPod. When it has finished (and if no other programme is using your iPod, such as anti-virus programmes) iTunes will confirm to you that it is then safe to disconnect the iPod (unplug the cable).
    If you unplug an iPod from your computer while iTunes or any other prgramme is using the iPod, it will probably corrupt the files and you may be unable to use some or all songs until you Restore the iPod.

  • I have a ipod, but recently updated my laptop, how do I get my ipod to sync with my new PC, when I connect the USB the ipod say's "connected" eject before disconnecting

    I have a ipod, but recently updated my laptop, how do I get my ipod to sync with my new PC, when I connect the USB the ipod say's "connected" eject before disconnecting

    See KB Article:  How to use your iPod to move your music to a new computer

Maybe you are looking for

  • How to design ageing report

    hi friends How to create ageing reports.If any one has documents/links pls provide me..

  • How to put ZEBRA color in F4 Search help

    My Requirement: Suppose I am having a search help with the following data. MATNR SLNO OPERN PREHT A 1 A1 X A 2 A2 A 3 A3 X A 4 A4 B 1 B1 B 2 B2 B 3 B3 C 1 C1 C 2 C2 Now I want to display the Search help with two colours [ZEBRA] as shown above. The cr

  • IMac display problems (twice now)

    I am wondering if anyone has run into the problems I have dealt with. I bought an iMac Core Duo 20inch two weeks ago. I got home, set it up and immediately noticed 7 dead pixels. I called up apple and complained to four different reps until they fina

  • Can someone do my graphics for me

    basically i need someone to make my animal bend down using different amount of pictures to do it. let me know if you can for free

  • Is there any other alternative instead of using of WAIT UP TO X SECONDS?

    Hello I am developing a inteface function module that gets iits input data from another system (HR system), in that I am using WAIT UP TO 5 SECONDS statement, but my lead is not OK for using it, pls. let me know can I achieve the same by using any ot