My new I pad three connects to the internet but only for a brief period of time. I then have to restart it only to get the same results.

My new Ipad 3 connects to the internet but only for a brief period of time. I then have to reboot only to get hte same results. Any suggestions?

You are correct.  Syncing should transfer any purchased media, including videos, from your device to your iTunes library provided your computer is authorized for the Apple ID used to make these purchases.  You mentioned that you have uninstalled iTunes before, but if you didn't follow this guide exactly, uninstalling iTunes and all of its components in the order specified, it may not have been successful so you should try again:  Windows XP or Windows Vista/7.

Similar Messages

  • HT3964 i have a iphone 4 that was dropped in water for a short period of time. it then was put in rice to dry it out. and now i'm trying to restore the iphone and it will not restore. what do i do now?

    i would like to know what i need to do?

    If the iPhone was in water, the dry rice for a week trick sometimes works, sometimes does not work.  If it does not work your only choice is to take it to an Apple store genius bar and see about a replacement.  For an iPhone 4 the out-of-warranty replacement is $149 in the US.

  • Two computers connected in the same port dot1x in 3750 in different time.

    I have the following consultation.
    I have a "computer A" connected to a port of switch 3750, configured with: dot1x port-control auto
    dot1x timeout quiet-period 5
    The "computer A" is authorized.
    When I disconnect the "computer A" and I connect a "Computer B", this is not connected, but when I connect the "computer A" again if is connected.
    How many time I should expect to be able to connect the "computer B" in the same port of the 3750?

    When the switch cannot authenticate the client, the switch remains idle for a set period of time and then tries again. The dot1x timeout quiet-period interface configuration command controls the idle period. A failed authentication of the client might occur because the client provided an invalid password. You can provide a faster response time to the user by entering a number smaller than the default.
    The value after the quiet-period is in seconds, so in your case, the switch will wait five seconds before it re-tries for another authentication for the new device connected.
    Please rate helpful posts.

  • FIM 2010 CM and FIM CM 2010 R2 in the same Domain and connecting to the same PKI

    Hi,
    I have a requirement to upgrade my FIM CM setup from FIM 2010 to FIM 2010 R2 SP1. I am not looking for an in place upgrade, instead I would like to have a new parallel setup (new FIM 2010 R2 servers, new SQL 2012 servers), connecting to the same AD and PKI.
    Thank You.

    Hi JPM
    Yes, you can do a parallel setup, but keep the following things in mind:
    1) Do you plan to manage the existing certificates, if so, then you need to make a cut-off and migrate the FIMCM database to the new SQL server. If you keep two instances, you will have certs that cannot be managed in each.
    2) You will need to migrate the clmKRAgent, clmAgent, and clmEnrollagent certs to the new FIM CM server
    3) You should use the same SCP (to maintain permissions)
    4) I would migrate any changes in web.config to the new server
    I would not use the previous FIM CM setup after the migration is complete. Keep it for roll back during the upgrade. but do not allow connectivity afterwards
    Brian

  • HT201263 I completed the steps outlined above for recovery.  after completion I see the same screen showing the "connect to iTunes". step 4.  Again I went through the recovery with the same result.

    I need help with restore on my iPad 2.  After updating the OS to 7.0.4 I see a screen showing that I need to connec to iTunes on my computer.  After resrore is complete the same screen appears,  I disconnected the iPad the re-connected with the same result.  I used restore twice and am still getting the same result.

    Your iPad is in recovery mode.
    http://support.apple.com/kb/HT1808

  • Every time I try to update the creative cloud desktop I lose my taskbar etc - have to restart windows explorer to get that back, but I cannot update the desktop app

    Every time I launch the creative cloud desktop app it says I need to update.  When I follow the prompts to update I lose my taskbar, etc on my windows 7 machine.  I then have to restart windows explorer to get the desktop back, but the app still now says I have to update.  Circular problem - please help.

    Repeated updates http://helpx.adobe.com/creative-cloud/kb/updates-repeatedly-applied-cc.html
    or
    Creative Cloud chat support (all Creative Cloud customer service issues)
    http://helpx.adobe.com/x-productkb/global/service-ccm.html

  • I am using Windows 7 Pro, 64 bit on a brand new PC, and cannot connect to the iTunes store using iTunes version 10.  HELP!!

    Ok, so after purchasing a new computer, with windows 7 pro, 64 bit, I tried downloading the newest iTunes, which at the time was 10.2.1 (i believe).  After installation, everything seemed to work, except that iTunes was unable to securely connect to the internet, use home sharing, or validate my computer.
    As troubleshooting, I first ran msconfig, and then turned OFF all programs that boot at start up EXCEPT itunes and quicktime.  After a restart, i opened itunes again, and got the same result.  That led me to believe that iTunes was NOT being blocked by another program on my machine.  I am currently running itunes 10.7 successfully on a Windows 7 32 machine at work.  Anyhow, for grins, I tried to install version 9 on the new computer, and it installed perfectly, and immediately connected to the itunes store, leading me to believe that there is nothing wrong with my software configuration (not sure if this is a safe assumption or not).  I then tried to let iTunes update itself using the automated update function.  It tried to update itself to the most current version, then 10.6.  Again, iTunes was unable to connect to the iTunes store.  I HAVE tried disabling the anti-virus software (AVG), but that made no difference. 
    I have since gone back and reinstalled iTunes 9.  Here's the catch though.  When I reinstalled using version 9, I had to redo all my library files.  I'm about 1/2 way through my CD's, and now have a substantial library file going.  The last time I let iTunes update itself to 10.6, once I realized that it was not going to connect to the store, I uninstalled iTunes, and reinstalled ver. 9.  However, when I did this, it told me it could no longer open the library file, because it was a newer .itl or .xml (i believe it was one of those two extensions) library file.  At that point, I basically started everything over again, using version 9, and have been importing CD's like a madman at night.
    Here are my questions:
    1) Is there a way to make a copy of the files that store my library info, so that if my upgrade to ver 10 IS NOT SUCCESSFUL, I can restore ver 9, but still have all of the album art work, playlists (when I import music, I create a playlist with the artists' name, and store things that way), etc. in tact? 
    2) What else can I try (firewall settings, internet options, etc.) to try and get version to to successfully install?  I would really like to get all the benfits of the newer versions.
    3) When I tried to get apple tech support before, they wanted me to pay a ridiculous 69$ fee for phone support.  I just bought an iphone 5....this should entitle me to a fresh 90 days of phone support, right?  The reason I ask here is that I could hardly understand the "tech" that answered the phone when I called for tech support last time, and to be honest, it really ****** me off that they wanted to try and milk me for another 69 bucks....I've purchased every iPhone since the 3Gs came out (pre-ordered at that), and have nearly gone broke purchasing music from their iTunes store....heck, maybe they're doing me me a favor not letting me into the store, huh?
    Any help or ideas would be greatly appreciated,
    -Brian

    Many thanks.
    With those symptoms, I'd try the following document:
    Apple software on Windows: May see performance issues and blank iTunes Store
    (If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.)

  • HT1338 Does anyone have a fix for the error message "Because a USB device was drawing too much power from your computer one or more of your USB devices have been disabled" - this is a brand new machine with nothing connected to the USB ports - i've done u

    Hi
    does anyone know how to fix the message on my iMac:
    "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled."
    This is a brand new machine and did not have anything attached to the USB ports"
    Thanks for any help

    If you are getting that message on a brand new Mac with nothing connected to the USB ports, take it back. It is broken.

  • HT4437 I bought a brand new iPad 3 and an Apple TV, both connected to the same wpa protected wifi network from home. It worked for a day, but when I woke up, the Apple TV couldn't be found anymore by neither iPad, MacBook or iPhone. Any clue? Thanks!

    I bought a brand new iPad 3 and an Apple TV, both connected to the same wpa protected wifi network from home. It worked for a day, but when I woke up, the Apple TV couldn't be found anymore by either iPad, MacBook or iPhone. Anybody a solution for this?

    Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
    Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
    Thanks again!

  • I have a new Epson wireless printer connected and the iPad recognizes it but it won't print. What is AirPrint and how do I connect it?

    I have a new Epson wireless printer connected and the iPad recognizes it but it still won't print.  What is AirPrint & how do I connect to it?

    Patti-
    Is your Epson printer on Apple's list of AirPrint capable printers?  See <http://support.apple.com/kb/ht4356>.
    If it is an AirPrint printer, then your WiFi router may not correctly handle Bonjour data required by AirPrint.  Contact the router's manufacturer to see if there is a change to its setup or a firmware update, that will make it work.
    One other possibility is that there could be a print job stuck in the iPad's print queue.  Double click the iPad's Home button and a row of recent Apps will appear along the bottom of the screen.  Scroll across and see if the Print Center is there.
    Fred

  • I have downloaded itunes on my new computer and connected my classic ipod, but only the tunes that I purchaes from  Itunes appear. How can do I transfer all my other songs over without  deleting them all

    I have downloaded itunes onto a new computer and connected my ipod classic, but only the tunes purched from Apple appear. How can Itransfer all my ipod library onto the copmter without deleting them

    See:
    Recovering your iTunes library from your iPod or iOS device: Apple Support Communities
    If further problem post in the iPod Classic forum. This is the iPod touch forum

  • TS1470 Hi we are all connected to the same iTunes account . My daughter and I received new phones yesterday and now can not connect. When we put our apple ID password in it then asks us to answer our security questions. Which was the ones we did not selec

    Hi my daughter and I both received new phones yesterday. We are both connected to the same ITunes account . When we now go in to buy a song or app it is asking us to complete a security questions but the questions it is asking is not the ones either of us selected in the first place.my daugher has the iPhone 4 and I have the new 5

    Hello, Dannielle.
    This article will help you reset your security questions as long as a rescue e-mail is added to the account.  If one is not attached then contact us at https://expresslane.apple.com/. 
    Rescue email address and how to reset Apple ID security questions
    http://support.apple.com/kb/HT5312
    Cheers,
    Jason H. 

  • HT4061 Got new router my samsung galaxy will connect to my printer and eprint but Ipad won't connect keep saying connect to the same network  this ipad connected before but now it won't

    I had upgrade of new router my samsung galaxy can connect to my printer and eprint but my ipad won't  it says connect to the same network my printer is hp deskjet 3550A printer my ipad connected to my last router

    Hi Pvclayton,
    If you are having issues with AirPrint on your iPad, you may find the following article helpful:
    Apple Support: AirPrint Basics
    http://support.apple.com/kb/HT4356
    Regards,
    - Brenden

  • New-Pssession client cannot connect to the destination specified

    I've used the following cmdlets to connect powershell to our tenant for months and now I cannot open a possession with the same commands.
    I've searched on some of the error text show below without any great progress. We have a pair of Hybrid servers and we get the same result on either.
    Any suggestions are appreciated.
    Bruce
    Import-module msonline
    $O365Cred = Get-Credential
    $O365Session = New-PSSession –ConfigurationName Microsoft.Exchange -ConnectionUri https://ps.outlook.com/powershell -Credential $O365Cred -Authentication Basic -AllowRedirection
    Import-PSSession $O365Session
    Connect-MsolService –Credential $O365Cred
    [email protected]
    working password at the MicrosoftOnline Portal
    $O365Session = New-PSSession -ConfigurationName Microsoft.Exchange -ConnectionUri https://ps.outlook.com/powershell -Credential $O365Cred -Authentication Basic –AllowRedirection
    WARNING: Your connection has been redirected to the following URI:
    https://pod51038psh.outlook.com/powershell-liveid?PSVersion=4.0
    New-PSSession : [pod51038psh.outlook.com] Connecting to remote server pod51038psh.outlook.com failed with the following error message : The client cannot connect to the destination specified
    in the request. Verify that the service on the destination is running and is accepting requests. Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or WinRM. If the destination is the WinRM service,
    run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". For more information, see the about_Remote_Troubleshooting Help topic.
    + $O365Session = New-PSSession -ConfigurationName Microsoft.Exchange -ConnectionUr ...
    + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [New-PSSession], PSRemotingTransportException + FullyQualifiedErrorId : CannotConnect,PSSessionOpenFailed
    Import-PSSession $O365Session
    Import-PSSession : Cannot validate argument on parameter 'Session'. The argument is null. Provide a valid value for the argument, and then try running the command again.
    At line:1 char:18
    + Import-PSSession $O365Session
    +                 
    ~~~~~~~~~~~~
    + CategoryInfo         
    : InvalidData: (:) [Import-PSSession], ParameterBindingValidationException
    + FullyQualifiedErrorId : ParameterArgumentValidationError,Microsoft.PowerShell.Commands.ImportPSSessionCommand
    Connect-MsolService -Credential $O365Cred

    You are using the outdated URI string, which is known to cause problems. Should be: https://outlook.office365.com/powershell-liveid/
    Just follow the instructions in the TechNet article:
    https://technet.microsoft.com/en-us/library/jj984289(v=exchg.150).aspx

  • My new ipad does not connect to the 3G network

    my new ipad does not connect to the 3G network, only the network edge. what to do in this case (no 3G connection available in my location, even did tests with modems and cell phones)?

    connection exists, because I connected with the iPad, but two weeks is not connecting more ...

Maybe you are looking for