My new mac mini (3 month) didn't start up,all that appeared was a white screen and a flashing folder with a question mark inside it.
My new Mac mini (3 month) didn't start up, all that appeared was a white screen and a flashing folder with a question mark inside it.
I followed by recommendations from 'Everything Mac': "shut it down by pressing and holding the power button for about 5 seconds.
Then hold down the Option key and press the power button again to start up the Mac mini. Keep holding down the Option key until
the Mac mini starts up."
But I got a Wi-Fi button only to chose and connect the local network. I connected to my network and I can't use this connection
becouse no icons.
Could you please help me?
Your Mini (running 10.6.4) should have come with grey-colored install disks. Now is the time to put them into service. Turn on your computer so that there is power to accept disk #1 into the optical drive. Once the disk is in the drive, shut off the computer by holding the start button down until it powers off. Then turn it on this time holding down the "C" key to make the computer boot from the disk. The question mark that you saw indicates that the computer cannot find a bootable volume. This can happen due to corrupted system files or an improper shutdown etc. Once you are in the "Installer" you can choose Disk Utility from the Utilities Menu in the menu bar. Use it to repair the disk and to see if that can solve your trouble.
Similar Messages
-
I got a flashing folder with a question mark. I got a new hard drive and upgraded to 4 gigs and can't open anything or reload the operating system? Help? FYI: I have been using boot camp with windows 7 and started getting a kernal_data_Page_error and it would reboot windows, i was trying to do a chkdsk on the next reboot, but thats when i started getting this issue. I have put in a new hard drive and went from 2 gigs to 4. I can not get the computer to do anything, even the monitor does not show anything now????
Prep your new drive:
Drive Preparation
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs,) then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
After formatting has completed quit DU and return to the installer. Install OS X. -
So I came to this problem a while ago. M ycomputer basically froze so I was forced to shut down by holding the button down. When I started it up I got the flashing folder with a question mark. I started it up holding down the command and r keys which brought me to disk utility. Although my computer doesn't read that I have a hard drive to start it up. When I click on the disk utility app, I cannot verify or repair anything either. The buttons won't allow me to click on them. It also shows "Mac OSX Base System" which shows I have files and what not saved. I had been told that I need a new hard drive so I bought and manually installed a OWC SSD 240GB drive and when i booted the computer up it booted up yo the operating system fine with all my files and what not on there. After about twenty minutes, it froze again. I forced a shut down, restarted and the same thing happened. I am not able to choose my SSD to boot up, although thats probably because it doesn't have an operating system installed on it??
i have a Macbook Pro 13" 2011
any help would be great, I'm overall confused.ryansaint11,
this isn’t Apple support; this is a user-to-user forum. We’re just fellow users of Apple products here.
If you want to boot from your SSD, then you should put the SSD where your HDD currently is, and put the HDD into the optical bay. (That setup will also get you the best performance.) At the moment, you’re still booting from your HDD. Note that you will need to format your SSD in Disk Utility [with the “Mac OS X Extended (Journaled)” format] so that you can install OS X onto it.
Since you have an Early 2011 model, it might or might not have originally come with grey installation DVDs. You will be able to find out whether it did or not by trying to use OS X Internet Recovery to install OS X onto your SSD. If it does not work, or if the installed OS turns out to be Snow Leopard, then it will have originally come with the DVDs, and you should purchase a replacement pair of DVDs from Apple or iFixit; those discs will have your MacBook Pro’s Apple Hardware Test and its iLife apps. If the installed OS turns out to be Lion, then it will not originally have come with the grey installation DVDs, and your Apple Hardware Test will be installed along with Lion, and your iLife apps will be downloadable from the Mac App Store. -
Hello, can someone help me: my eMac G4 700 MHz. I can not boot it. If he starts appears on the screen, only a small "folder with a question mark." The Mac was not used 1 year.
Question 1: Problem = hard drive?
Question 2: Problem = PRAM battery?
the
What can I do to boot?Restart with the Option key held down.
If the internal drive shows up, it's the PRAM battery.
If it doesn't, insert a compatible Mac OS 9 or X install disk, click the button with the circular arrow, and either repair the internal drive or install a new OS on it. If it doesn't show up in Disk First Aid(9) or the Disk Utility(X), it's either not plugged in or needs to be replaced.
(97530) -
On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder
Welcome to Apple Support Communities. We're users here and do not speak for "Apple Inc."
Power on the computer and insert the DVD immediately.
Hold down the 'C' key to boot from the Snow Leopard DVD.
http://support.apple.com/kb/ht1533
After selecting the appropriate language, if necessary, select Utilities, and Disk Utility.
You'll likely need to partition and format the new drive before it's recognized.
http://manuals.info.apple.com/MANUALS/0/MA161/en_US/MacBook_13inch_HardDrive_DIY .pdf
(Yes, these instructions ARE 7 years old, but the procedure is the same for installing from DVD media.) -
when i starst my mac i get a flashing folder with a question mark. i tried rebooting and holding the option button then i get 2 boxes, one with a refresh arrow and one with a forward arrow neither of them seem to do anything. now what
Here is an article that describes what it is supposed to do:
Startup Manager: How to select a startup volume
If no Volumes are shown, it is telling you there are no potentailly bootable Volumes attached. That means your boot drive has died or the bootable image on it is unrecognizable.
What Mac Pro ? by year, GHz, number of processors, screen size?
What Mac OS X ? -
When I start my Mac air I get a flashing folder with a question mark
I am trying to start my Mac air and I get a flashing folder with a question mark. When I turn the power of it shuts down but wen starting it comes back
Just being clear about your situation. When you hold down Option during boot it does not show a system volume or a recovery volume from which to boot. At that point if you select a network boot and you do not see a spinning globe that persists there a good while as it loads the recovery partition over the network. True?
A couple of more thinks to try:
Disconnect all of your external devices.
Reset PRAM
Boot with the option key again.
Standard things to try (which is sounds like you already have attempted) A flashing question mark appears when you start your Mac -
I just booted my mac book pro and it is at a blue screen with a flashing folder with a question mark in the middle of it. How do I get out of it?
Click here and follow the instructions. If the computer was running Mac OS X 10.6.8 or earlier and you reach the third set of steps, insert a Mac OS X install disk.
(126818) -
I have the mac book air and when I turn it on its a light blue screen with a flashing folder with question mark on it. Any one know how to get past it?
The MBA is trying to tell you that it is not able to find a bootable system
Either the file is corrupt or access to the storrage has failed
I would start by seeing if it will boot with Command + R depressed -
Hi I was wondering if anyone has experienced probs with the ios7 on iphone 4s, as mine keeps going white screen and wont turn on reboot unless im lucky. When, if it comes on it blurrs and fades out after a couple of minutes the screen also jitters and dies often. I dont know if this is due to the software update or a faulty screen etc... any thoughts?
Sno problems here at all.
-
After the screen turned white and the folder popped up, it just kept flashing. After a few minutes the screen just turned white completely and I could hear the noise of the drive. It just sat there still with the noise for a good few hours until the battery died and then my mac just shut down completely. I tried to see if the computer could charge, and it does charge. I just can not turn the computer on no matter what. It is dead. It might be the logic board or the drive...I'm hoping it won't cost me a new computer because I just got this 5 months ago....
Do not attempt to charge as that will only make the damage worse. You need to take the MacBook Air to an Apple store genius bar and have the technicians check and see what repair work is necessary. It only takes a very small amount of liquid to cause short circuits and damage.
-
I had to install a new hard drive for my macbook after my last one had obviously crashed and was making clicking noises. The problem is I can't install OSX on my new one and I'm getting extremely frustrated. What could be going wrong? I've reset PRAM and done everything I could find suggested online.
Have you tried inserting the Snow Leopard Install disc and using Startup Manager to select the Snow Leopard disc as the startup disk? Once you get started up from the Snow Leopard Install disc, the rest of the instructions can be found in the manual for your MacBook Pro. Here are the ones for mine:
Installing Mac OS X and Applications — New Hard Drive
from http://manuals.info.apple.com/en_US/MacBook_13inch_HardDrive_DIY.pdf
To install Mac OS X and the applications that came with your computer, follow these steps:
1. Start up from the Mac OS X Install Disc 1 that came with your computer, and choose your language.
2. From the menu bar, choose Utilities > Disk Utility.
3. Open Disk Utility and select the new drive in the list to the left. Note: If you are formatting the primary drive, use the Disk Utility program on the Install disc.
4. Click the Partition tab.
5. Click on Options, and verify GUID is selected if this is the startup drive.
6. Name the volume “Macintosh HD.”
7. Apply the change by clicking the Partition button.
8. At this point, either
• Quit the Disk Utility application, and proceed with the Mac OS X installation. Follow the
onscreen instructions. After selecting the destination disk for installation, continue following the onscreen instructions. Your computer may restart and ask you to insert the next Mac OS X Install Disc 2.
or
• Leave the Disk Utility application open, and restore the backed up files from the image
you created before removing the hard drive.
Installing Applications
To install just the applications that came with your computer, follow the steps below. Your computer must have Mac OS X already installed.
1. Back up your essential files, if possible.
2. Insert the Mac OS X Install Disc 1 that came with your computer.
3. Double-click “Install Bundled Software Only.”
4. Follow the onscreen instructions.
5. After selecting the destination disk for installation, continue following the onscreen instructions. Your computer may restart and ask you to insert the next Mac OS X Install Disc 2
6. Restore the data by reinstalling the backed up files from your backup to the new drive. -
Turned my mac book pro on and a folder with a question mark just flashes
TTurned my Mac book pro laptop on and all I get is a flashing folder with a question mark on the screen
Have you tried to boot in Safe Mode (keep the Shift key down while booting, until the Apple grey backdrop, spinning gear and progress bar appear)?
If you can boot that way, it means some third-party software is causing problems.
If not, try to boot in Single User mode (press the Command/Apple and S keys on startup), then type "fsck -y" (no quotes), press Enter.
You should get a return such as:
fsck_hfs: Volume is journaled. No checking performed.
fsck_hfs: Use the -f option to force checking
If you do, then your startup volume is accessible. Type "restart" (no quotes...), then press Enter.
If not, you can try the following command:
mount -u/w /
(there's a space between mount and the dash, no space between the dash and u/w, and a space between u/w and the slash sign).
There shouldn't be any visible return on screen after that command, but if you wait a few seconds, you could then enter the following command:
systemstarter
Then press Enter.
That could suffice to boot your system, but still not the graphical user interface.
When the prompt sign (#) returns, type "restart" (again, without the quotes), and press Enter.
Tell us how it went. -
Hi I installed a new hard drive in my Mac mini osx lion an when I turn it on I get a flashing file with a question mark. I tried holding command and R keys when turning it on but the recovery fails to work. I can hold the option key at start up and choose my network, then Internet recovery shows up with an arrow pointing up. When I click on the arrow Internet recovery fails and all I get is a globe with a triangle on it with an exclamation mark on it, and under that it says
apple.com/support
-6002F
Does any one know how I can fix this without a recovery disc? ThanksI just want to add to this, in case someone else searches for this error on Apple Support (google doesnt cover apple support.. how clever is that?)
I had the same error. And i had a Computer that had worked, with a SSD drive and 16GB upgrade done by the owner himself.
I tried swapping with a Mechinal Harddrive, no luck.
Kept the Mechanical drive in, and tried with some other Ram, it worked..
So for me this error and after reading the other responses can be boiled down to a Harddrive problem or Ram issue.
It was Ram for me.. -
From the little research l have done, l have been convinced l may be having a dead hard drive though after having tried all the other troubleshooting tips found here, when trying to boot l get the grey screen and folder with the question mark suggesting it can not find the files neccessary to boot hence l tried booting with the disc and the message l get is that mac OS X can not be installed on this computer, though after doing the hardware check etc they all say okay. I've even tried erasing the drive and trying to instal the OS afresh with no luck. Any ideas or l must just get a new hard drive?
Pretty sure BGreg hit the nail on the head. If your hard drive was failing, you would still be able to at least attempt an install, provided your ard drive was mounting. You usually get that message when the disk is incompatible with the computer. If it is the proper disk, you might try erasing the disk (provided your info is backed up) using Disk Utility (under Utilities in the menubar) and choose the Mac OSX Extended (Journaled) format.
Maybe you are looking for
-
Hello All, we are unable to do goods receipt in SRM. we are using SRM 5.0 When we try to post confirmation (BBPCF03), we could select the PO and when we click on "create confirmation" icon, nothing is happening. what are we missing? Thanks in advance
-
How to increase the number of scrollable shell/terminal lines?
Hi guys, I've just run "pacman -Syu" and got hundreds of error lines. When I tried to scroll up to the first one by pressing "shift-pageup" I noticed, that I could only go back a couple of lines. So apparently my terminal "forgot" the first few lines
-
How to Create Function Module BAPI_GETGLACCPERIODBALANCES Carry Forward
Dear All, In SAP there is a Function Module BAPI_GETGLACCPERIODBALANCES to carry forward balance GL account. But in this case GL account (Balance Sheet) that i used (BS200150) using IO Number as is cost object, I want to know if there is a function
-
Hello, I just received the news that Data Modeler went in production which is great news! The bad news is that it isn't free ;-) Where can I find clear information about it's pricing? Is it user or company based? Thanks, Matthias
-
How does an OS command level encryption is different from the Adapter Module encrytption Technique? thanks