My new T410 will not charge battery! Bizarre

Hello, Today I recieved a T410 laptop I purchased from ebay. (perhaps a mistake)
The laptop appears to work fine while plugged into ac, however the battery will not take a charge. Lenovo power manager says the batter is at 15% capacity and "charging", however this never increases and the laptop dies instantly when the power cable is removed. It does not turn on without ac power. When it is plugged in and closed, the battery charging LED is illuminated, however it blinks (i'm not sure if it is supposed to do this?). It is solid orange for 4 second and then one quick blink.
I have updated the bios, completely removed the power manager software and driver and reinstalled it. This has not helped my issue.
One concern I have is that I purchaed this laptop refurbished from the states. I am located in canada. I hope I am eligible for warranty service.

Sounds like the battery is defective. You should be able to get it replaced if the laptop is still within the first year of warranty. Whether or not Lenovo will acknowledge your request depends on where the warranty applies.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Similar Messages

T410 Will not charge battery!

I have a T410 which does not charge the battery. I have installed the latest BIOS and Power Management software without any thing changing. I noticed that even with a fully charged battery if unplugged from the AC adapter it will die instantly as though the battery is dead! Could this be the system board? I'm not sure what else to try in diagnosing this issue.

lead_org wrote:
it could be an issue with the battery. Call service support and they should direct you on what to do.
Well it appears it's not the battery or the software because I had another new still in the box T410, Type 2522-22U of which I used to interchange batteries and power adapter with. One last thing I tried was switching hard drives with the factory fresh image on it and I found that O/S to behave the same way in this laptop. Still reports the battery at the same charge and not charging. Looks like its the system board. Apparently there is a circuit on it that regulates the charging process. That same battery in the NIB laptop charges just fine!

Palm Pre crazy symptoms: "phone offline", will not charge battery, will not start, error message "an error has occured that cannot be resolved"

This is a long description of a series of problems with my new Palm Pre. You may wish to search the text to find your specific issue(s). There is no solution in my post. Look for possible answers in the responses to come.
I bought my Palm Pre 4 days ago and it arrived 2 days ago. Phone worked great. Last night I plugged in the phone and updated the OS. After completion, I selected "Done" and went to bed.
- First Series of Issues: "Phone Offline", will not charge battery -
In upper lefthand corner of the phone there is the message "phone offline". Although the phone has been charging all night it reads "26% battery". I called the general Sprint tech support number and we tried the following things:
1) Restart phone (press and hold power button, then select "turn off". after power down, press and hold power button to power on.)
2) Reset the phone (several different ways - call tech support so that you do this correctly)
The individual at Sprint then sent me to another tech support person, presumably 2nd tier.
- Second Series of Issues: Error message "an error has occured that cannot be resolved" -
Sprint tech support person #2 also had me restart and reset the phone in a number of ways. In her words "we've tried every palm pre trick I know" and each time the phone was unresponsive. Often we received the error message "phone is offline". We did a full erase and after that the phone would no longer restart. At this point the error message came up saying "an error has occured that cannot be resolved" which referred me to www.palm.com for assistance. I think it's important to note here that this was not the typical error message (black screen with white letters) but rather the blue sky background with a semitransparent box over it with white text.
Sprint tech support person #2 then connected me with Palm support and the dance continued. Again we tried a whole bunch of resetting and restarting and erasing options. Palm support instructed me to go to: www.palm.com/rom to download WebOS Doctor, which I did. I downloaded the file. While that was happening he had me hold the "volume up" button and plug the phone into the charger. This caused a USB symbol to appear on the phone. When the file was complete I received an error message that the file couldn't run. Palm tech support person seemed surprised. I mentioned that I was on a Mac and he said he couldn't help me. He then transferred me to another Palm support person who works with Mac users.
Palms tech support person #2 then informed me that I should have selected the "mac" download option on www.palm.com/rom. I verbally walked her through the whole series of webpages, telling her that it says that you need Windows (version whatever) or Mac (version whatever) but that at no time was there an option to download a different WebOS Doctor for different operating systems. After some more discussion she told me she would have to have someone call me back tomorrow.
- Third Series of Issues: phone stuck on USB symbol -
So at the moment the phone is completely useless. Not fantastic. I booted up the mac in Windows 7 and downloaded WebOS Doc and received the same error. I also ran Windows Vista virtually and received the same error. Later this afternoon I'm heading into work to try the same thing on Windows XP.
In the meantime, I got onto this forum and located a thread that provided a direct link to the necessary file:
palm.cdnetworks.net/staging/rom/webosdoctorp100ewwsprint.jar
After downloading that file, which I realized could totally be a virus, I was able to get WebOS Doc working on my computer. It required that I recharge the phone completely before beginning and now it's on the screen that says "Don't disconnect your phone" and the file is at 3% complete. Only... it's been at 3% complete for almost 30 minutes.
I am hoping that Palm will follow up with me tomorrow, but I'm leaving at 7am on a business trip and would love to have the thing working. Any suggestions are welcome, even if you can just tell me how to get the think disconnected safely before my flight tomorrow. I don't fancy getting through security with my phone wired to my laptop.
Thanks.
Post relates to: Pre p100eww (Sprint)
This question was solved.
View Solution.

Hello and welcome to the forums;
Our phone support is open every day Monday through Sunday, although there are different hours of operation for the weekend. If after a webOS Doctor reset you are still experiencing the same problems, I would likely recommend replacement, either in a local store for your carrier or through our technical support department.
There may be additional technical support offered or suggested over the phone, this would need to be done first before a replacement could be issued.
Hope this helps,
TreoAide

My brand new PB will not charge when in standby or when on

I played with a number of PB's so far and finally have my own but... My brand new PB will not charge when in standby or when on; as soon as I plug the charger into the USB port it detects it and brings the screen up (if in standby) showing the lighting bolt on the battery but it does not charge; the lighting bolt stays but the % charge does not change (or hopefully increase) at all; it will actually decrease (??); the only way I can charge it is when I attach the charger and the PB is powered off… the PB brings the red (or green can't remember) LED on and starts to flash it on off and charges; tried the hard reset with no change; I am running the latest OS release 1.0.8.6067. Has anyone seen this? Is it h/w or f/w? Any Fix?

Here's a final update on this... the units goes back to its maker or the store sometimes tomorrow... Why? First I tried to understand if this was s/w or h/w related or maybe both before calling support which in the end I did; so I did try a different charger, hard resetting the unit, discharging and recharging etc; nothing helped or fixed the charging in standby; the unit continued to charge only after being turned off and then plugged into the charger. Here's what I learned:
1. Going through the initial setup and OS update it is quite possible for the unit to NOT load the OS image correctly i.e. it appears that it loaded the OS and displays the OS version as if it loaded properly when in fact it did not and the image loaded is corrupt. I found this out during a live session with support when they were looking at my PC screen while the PB was connected to the PC only to point out that the Desktop Manager was showing a s/w update being available (1.0.8 bundle 6067) while the unit was reporting 1.0.0 bundle 0. Strange, I thought I already had 1.0.8.6067... after accepting the update, which takes a bit to load, I started more testing, charging, discharging, hard reset (i.e. Volume Up + Power) etc with no positive results to report. This also proved that the USB port is working, both data (PC to PB communication alright) and power (PB displays the plug over the battery bar when the power contact work)
2. The charger I have works and it is the correct one: P/N PSM09A-050RIM; make sure it is not one of the incorrectly rated chargers some received.
3. In order to reduce the amount of current the unit consumes when on, you have to run the Video Chat app at least once and acknowledge the (c) page; otherwise this remains as a background app that take more CPU cycles on the battery. After doing this I did notice a slight improvement in the sense that PB did charge some instead of discharging. The problem is that it only charged to about 60% and did not move higher no matter how long I waited (yes I did reset just to make sure it is not the s/w acting up and deciding to not update the power bar)
4. The way the RIM RMA works is like this: they start the process for you to return the unit back for repair which I understand may take 10 days; you may get a unit to use for this time if so desired, it will be charged to your CC; your unit may get repaired if possible; if not possible to repair, your new unit will be replaced with a refurbished unit; once you get some unit back you need to send the “10 day replacement unit” to RIM to get your CC charge cleared. I find that this program is good for when you can not return the unit to the place you purchased it from. Otherwise it is not good as I do not like getting a refurb for something I consider brand new (not to mention that you may get a unit with a few bright or dark pixels)
5. Throughout this process I looked at three (3) Playbooks: 2 had bright pixels and were returned immediately; this last one does not charge correctly. No win for me!
6. The battery lasts approx 4 hours with the unit playing a video clip in a loop and WiFi on with a WEB pulled stop watch running as well (had to allow multi tasking in setup/general).
Finally, my theory about this problem is that it is h/w related and that it is caused by the noise the board or the display is making when the unit is either on or in standby; a component not soldered properly (cold joint) or out of spec may be the culprit; for example a resistor in resistor divider monitoring the battery voltage or a decoupling capacitor missing or not soldered...

Since my I upgraded to ios7 my iPhone 4 will not charge, battery completely dead. Any ideas

Since my I upgraded to ios7 my iPhone 4 will not charge, battery completely dead. Any ideas

I updated my iphone 4 to ios7 three days ago. It now will only charge if connected to a computer USB port, either Mac or windows. It no longer charges on any wall mounted USB cable, like it did before the upgrade. The wall mounted cables still work just fine with an iPhone 4S and a new iPad retina display but not at all with the iPhone 4. Took it to a genius at apple store and they checked the battery. It still charges to 80% of original. They were clueless and suggested I replace the unit. It seemed to be related to ios7

My new iphone5 will not charge,any suggestions

Hello, my new iphone5 will not charge, when I plugged it in to recharge, it was making beeping sounds for about 5 minutes then stopped, any suggestions? thanks

First of all, you'd probably want to move this question out of iPod classic category to iPod touch one.
Try reconnecting your cable. Try connecting to your computer instead of wall socket, or vice versa.
Try resetting, restoring, restoring from backup. Make sure there's nothing wrong with your cable and try another one. The problem might be in your connector or the cable, if so — you might want to ask for a repair in your local Apple Store or Apple Authorised Reseller.

T43 1875-D6U will not charge battery or power on.

I have a T43 1875-D6U that has a power issue.
I replaced the A/C input jack and purchased a new genuine battery but the system will not charge the battery. I have tested, with a multimeter, the wall outlet, the a/c power adapter, the power jack connection opening and the connection to the board, and i have tested the battery terminals at the board --- everything checks out as getting power.
When i received the new battery, there was 5% battery life because the OS booted and i could see the battery indicator on the SYS tray but system would still not charge the battery. Now the battery is dead and I am back to "square one".
I have disassembled this laptop 5 times now trying to troubleshoot this issue.
PLEASE ADVISE!
[email protected]
Sean Doran
[email protected]

Hi, I am having the same problem. But as yet no-one seems able to provide a solution. Have you made any more progress with this?

Brand new phone will not charge

Just got my new 4S. It will not charge. Apple logo appears when pressing home button, but suddenly disappears or phone goes dead during initial config. Tried different chargers. Have tried charging for hours. Defect battery on a brand new phone?!

On your Manage Connections screen, click on the Services Status.
What is the status of the BlackBerry Internet Service?
Do you see the BlackBlerry dots logo at the top right of the home screen next to the signal bar indicator?
If not, and if the BIS status is not connected, could be the plan is not yet provisioned by Tesco.
Then, try this:
On your BlackBerry device, go to:
1. On OS5 devices: Options > Advanced > Host Routing Table > Menu > Register. On OS6 devices: Options > Device > Advanced > Host Routing Table
2. Resend your service books from your carrier BIS site:
From your handheld device:   http://www.blackberry.com/btsc/KB15402
Go to the Personal Email Set Up icon and log in. Then under Help!, select Service Books, then select Send service Books.From your desktop PC: http://www.blackberry.com/btsc/KB02830
North American Carriers - scroll down to select your carrier
WorldWide Carriers - Find your carrier on the list
3. With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot. This reboot, even if you have already done this, is often needed to install the service books.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

HT1476 upgraded my IPOD 5 to iOS 7.0.2 and will not charge battery. when plugged in gives message "This cable or accessory is not certified and may not work reliably with this IPOD".

Just Upgraded my IPOD 5 to iOS 7.0.2 and it will not charge the battery anymore.
When I plug it in, it now gives the message "This cable or accessory is not certified and may not work reliably with this IPOD".
Anyone else have this issue after they upgraded the iOS system?
Thanks,

- See:
iPod touch: Hardware troubleshooting
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Hi my new ipad will not charge in mains or PC??

hi I have had my brand new ipad for about a month and i can't seem to get it to charge it charges when it wants so to speak, I've tryed it in the mains in about 10 different plug sockets and on 3 PC's one been a laptop and it doen't charge when you want it to. what help can you give me?????

When you plug into a computer, it may say "not Charging", but it will charge but slowly. If this is the case, the cable is good. Therefore, the wall charger must be defective.
Take it to an Apple Store for evaluation.
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/
FYI
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
And this - Unplug the charger from the iPad and then replug. May resume charging.
Or - Recalibrate the battery. See link below.
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

Power book will not charge, battery just replaced.

Recently the power adapter or the power connector on my computer would easily disconnect from each other.
This morning I noticed that it was not charging at all, played around with it trying to jiggle it into place yet it does not have any connection.
Before I go and spend $100 on a new charger,or $200 on a service bill, is there a way to tell if it is the adapter or the connector on the powerbook.
I noticed on the cylindrical plug that the silver tube has seperated and was wondering if that would have to be sealed in order to maintain a ground.
I know it is not the battery as I was able to get one on warranty, through apple care, and it charged full last night, which it is showing 4 hours left.
Thanks
-jim

is there a way to tell if it is the adapter or the connector on the powerbook.
The easiest thing to do is go to an Apple store where they will have a working power adapter, or if you have a friend with one, use it. It sounds like the female socket itself may be shot, which would require replacing the DC-in card, which is around a $75+ part, plus labor to install.

TS3274 My brand new iPad will not charge. What is wrong? What should I do?

Just took it out of the box. It's the best one. It remains at 41% after being plugged in overnight.

The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
Since you are a new iPad owner .....
You can download a complete iPad User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
Apple - iPad - Guided Tours
http://www.apple.com/ipad/videos/
Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
How to - Articles & User Guides & Tutorials
http://www.iphone-mac.com/index.php/Index/howto/id/4/type/select
iPad How-Tos http://ipod.about.com/lr/ipad_how-tos/903396/1/
You can download this guide to your iPad.
iPad User Guide for iOS 5
http://itunes.apple.com/us/book/ipad-user-guide-for-ios-5/id470308101?mt=11
 Cheers, Tom

Brand new cord will not charge it?

Okay, so this morning when my mac was charging my dad moved it from the couch to the table, and in the process moved the extension cable it was connected to to the floor, my 15 week old rabbit decided that my lovely white power adapter looked tasty and decided to chew it. I came back to my computer and picked up the long white cord because i was going to move it so my rabbit wouldnt chew it and discovered he already had by the big chew marks he had made where the wires were exposed were sparking. Long story short, i took it to my local apple store they told me it wasnt covered, i payed $89AUD for a new one and got on with my life. I used my mac this afternoon without it plugged in as it was allready charged from this morning. I plugged it in tonight and realised that it wasnt charging. On my bar it says (Not Charging) and then on the drop menu it says.
Battery Is Not Charging
Power Source; Power Adapter
Its keeping it working, but it isnt charging it? My old one and my new one are both 60W. I have tried plugging it into many different places none work. What do you think is wrong?

There have been a lot of variants of the MacBook Pro since its introduction in 2006. One variant (can't remember which), required a software solution to work with the newer "L" shaped power connectors. Without knowing which you have, the best thing is to see if Software Updates offers you a patch.
There are also reports of some of the older, silver-key MBPs having a problem with the fit of the new adaptors.
Lacking that, I'd take the computer and the new adaptor to an Apple Store or AASP and stand there until they can provide an adaptor that works. Leave the rabbit at home.
Man! I though cats were tough on computer cables!

My iPhone 4s will not charge battery

my iphone 4s left 5% battery last time i use it but somehow dead and I try charge bettry but not charge at all

I cant understand! :((
Can you explain more.…?

Brand new phone will not charge after battery low

My daughter has had her phone 4 days and it has only today died completely it had icon in corner saying off so I put it on charge. But where the battery icon was there was no sign to say it was charging. I left it an hour and nothing so I did a battery pull and it rebooted but then died completely. Still no light on to say charging. I also read on another forum to plug charger in while battery removed but still nothing at all. Also before this when she put her simcard in which is a contract bb sim it was saying it wasn't connected to bb Internet and bbm was not working. Please help

On your Manage Connections screen, click on the Services Status.
What is the status of the BlackBerry Internet Service?
Do you see the BlackBlerry dots logo at the top right of the home screen next to the signal bar indicator?
If not, and if the BIS status is not connected, could be the plan is not yet provisioned by Tesco.
Then, try this:
On your BlackBerry device, go to:
1. On OS5 devices: Options > Advanced > Host Routing Table > Menu > Register. On OS6 devices: Options > Device > Advanced > Host Routing Table
2. Resend your service books from your carrier BIS site:
From your handheld device:   http://www.blackberry.com/btsc/KB15402
Go to the Personal Email Set Up icon and log in. Then under Help!, select Service Books, then select Send service Books.From your desktop PC: http://www.blackberry.com/btsc/KB02830
North American Carriers - scroll down to select your carrier
WorldWide Carriers - Find your carrier on the list
3. With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot. This reboot, even if you have already done this, is often needed to install the service books.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

My new T410 will not charge battery! Bizarre

Similar Messages

Maybe you are looking for