My newer IPhone gets a weaker cell signal at the same time and place as my wife's older one. Help

My newer IPhone gets a weaker cell phone signal at the same time and place as my wife's older IPhone. Help!

What is the signal the difference?
Follow this guide and record the numbers you see...
http://lifehacker.com/5929546/see-the-actual-signal-strength-on-your-iphone-with -this-quick-tweak
If the difference is within ~10db there's not much to worry about.
Now if you see -130 and -80 that is an issue. (talk to your carrier)
But if you see -60 and -75, both phones are operating normally.
What are the iPhones in question?
Are you both on the same network? (what network(s) are you on?)
What data connection is available on each phone? (3G/4G/LTE)
Are the iOS and Carrier settings up-to-date?

Similar Messages

Generat two signals at the same time and reading voltage

Hii
i have try to generate two signals at the same time and read voltage from another port on the board(not have to be at the same time), i have not alot of expriens in labview
and i based my code of example(http://zone.ni.com/devzone/cda/epd/p/id/5197) from yours site and try to suit to my needs
now my problem is when i generat the 2 signals(that work perfect) i canot read voltage from another port on my CB-68LP
i can not find the problem and make it over i hope there is away to figer out and fix it.
i have two cards 6229, and two CB-68LP board.
labview 8.5.
my code is look like this - http://img142.imageshack.us/my.php?image=scrennshot2no2.png
(this works perfect).
and this is my code after suit to my need - http://img183.imageshack.us/my.php?image=scrennshotfl5.png,there is error exception at the right side.
the exception-
Possible reason(s):
Specified route cannot be satisfied, because it requires resources that are currently in use by another route.
Property: RefClk.Src
Source Device: Dev1
Source Terminal: 10MHzRefClock
Required Resources in Use by
Task Name: _unnamedTask<0>
Source Device: Dev1
Source Terminal: None
Destination Device: Dev1
Destination Terminal: RefClock
Task Name: _unnamedTask<1>
eyal

sorry...
The AO tasks is very important they will be synchronize ,it is very importent the two tasks will start at the same time
and after it run at synchronize mode i will need to make reading of voltage
i gust try to make simulation of machin (i give that machin AO and reading from it voltage that all)
first of all i make the two signals(synchronize signals).
and after it i will need to reading voltage.
i can make two signals synchronize together.
i can make reading voltage
but i can't make two signals synchronize together with reading voltage
it throw to me this error message.
i am looking for away to figer this out.
thank's for any help
eyal
Attachments:
test11.vi ‏130 KB

Can airport express send a G and a N signal at the same time?

I have two macs with wireless N in my home, and two pc's with wireless G. Can the airport express broadcast a wireless G and N signal at the same time? or does it need to be one or the other?

I purchased 2 airport expresses today and the answer to this is yes

Im trying to restore my iphone 3gs to its factory setting at the same time updating to a newer version 6.1.2. while restoring, itunes states"We're sorry, we are unable to continue with your activition at this time." i cant open my phone, what does it mean

Im trying to restore my iphone 3gs to its factory setting at the same time updating to a newer version 6.1.2. while restoring, itunes states"We're sorry, we are unable to continue with your activition at this time." i cant open my phone, what does it mean

99.9% of the time, the cause of this issue is the fact the phone was jailbroken/hacked to unlock it for use on networks other than the network the phone was originally locked to. Apple maintains a database of officially unlocked iPhones, and when Apple's servers detect phones such as yours, activation stops & you get the message you got.
So, either get a sim card from the carrier your phone was originally locked to, or get it officially unlocked, because it appears that it was not officially unlocked.

Since i got the new Iphone 4s it constantly drops calls. Apple have replaced the phone with another new iphone 4s but i am still having the same problem. I have checked with vodapohe that there is no issue from there end, given a new sim, still drops out

Since i got the new Iphone 4s it constantly drops calls. Apple have replaced the phone with another new iphone 4s but i am still having the same problem. I have checked with vodapohe that there is no issue from there end, given a new sim, still drops out

Have a look at this it might help
http://support.apple.com/kb/TS4148

Can't get 2 firewires to mount at the same time

i just bought 2 500 gb externals to set up a raid, and i can get either one to show individually, but not at the same time- either by daisy chaining or using separate ports. the second will even show up if the first is off when they are daisied. i don't know for sure that i've ever used 2 at once, but am fairly certain i have. the ports all work individually- both 400's and the 800. i tried 1 800 and 1 400 at the same time, and daisied with 800 main + 400 daisy and 800 main + 800 daisy, all to no avail. nothing wrong with the cables- i cross checked. it's flakey mounting and dismounting, too (for instance, stuff disappears once dismounted and won't reappear til i reboot, even if i restart the device).
i reformatted both drives to mac journalled. i searched and have followed the instructs to reset the firewire ports, repaired permissions (many times) zapped the pram, and shut down the comp for 15 mins, inc the power, without any other devices attached to troubleshoot each drive, all to no avail. one strange thing- even the 400 ports showed as 800's in the profiler. only one at a time will show there, as well- whatever is mounted (or the first i mount; the second doesn't show). i should note i had a drive go bad on the 800 port not once but twice in the past year, and assumed it was the drive (it was used), but now i'm wondering if the port's funky. do they go bad and how hard are they to replace?
i don't really want to have to reload my system- i have an awful lot of software loaded and am in the middle of a busy time, plus i suck at that. i'm getting ready to add a couple gigs of ram to speed things up, too. it should be here tomorrow. i'm a retoucher and work on big files that need backed up regularly, which is why i'd like to do the raid and just work off it. i'm not on tiger- have been waiting for leopard, and was so mad when they pushed it back, since it means i have to wait on cs3, too, which really hurts my business. but i'll be darned if i upgrade now and then have to pay again in 3 months. i wish they'd offer the upgrades at half price this close (or do like other co's do and upgrade for free within a reasonable amount of time- not 7 days). any advice i haven't tried? please?
G5 Mac OS X (10.3.9) dual 1.7 mh; 1GB ram; 2, 250's hard drive

ok- i will try to answer what i can, but bear with me- i'm really good at what i do, but this ain't it. some of what you asked i don't know where to find the answers to. to start, the drives are western digital my book pros, 500 gb each. they support firewire 400, 800 & usb. the old drive that failed twice was a lacie 500 gb, too (with the metal case- don't know the official name off the top). i have pro friends who have similar setups with no issues (and am seeking advice from them as well).
i have a 1.8 mh dual, but i do have 8 ram slots, and i wouldn't want to deal with a mac book pro. retouching just doesn't work well with laptops, and i don't travel so i'd have no need. when i'm ready to get a new system, i want an intel quad. hoping i can push that off a year or 2, with the ram additions and raid.
i'm not using pci fw800 card adapter. my friend says he thinks a hardware raid solution like the la cies that run off a SATA card would work better, but he was curious if i can do what i want with the PCI-X card and the drives i have (since i don't want to return them or spend huge amounts more of moolah). so, do you know if i did get one if it would make the raid work? or would a 400 card be better? i'm not a photog filling a tb with each job (which my other refs are) so i don't need the huge volume of space that they do. but i do work on some pretty big files at times, and it can add up quickly. i think a terabyte raid would hold me for quite a while- which is why i did the 2 500's.
when i unplugged the machine and left it down for 15 mins, i unplugged everything, inc power cord, except the mouse and monitor cable, per instructions i found through the apple site.
normally i don't care to be on the bleeding edge and wait a little while to get new software, but it seems like i've waited so long, and leopard has so many features i think would be great. my buds agrees with you that getting the stable os is the best bet, and that i'm being too cheap. i guess that's the next step then, huh?
here's what the profiler says in general: Machine Model: Power Mac G5
CPU Type: PowerPC 970 (2.2)
Number Of CPUs: 2
CPU Speed: 1.8 GHz
L2 Cache (per CPU): 512 KB
Memory: 1 GB
Bus Speed: 900 MHz
Boot ROM Version: 5.1.4f0
Serial Number: ********
and specifically about the firewire:
FireWire Bus:
Speed: 800 Mb/sec Speed
External HDD Device:
Capacity: 465.76 GB
Manufacturer: WD
Model: External HDD Device
Removable Media: No
Detachable Drive: Yes
BSD Name: disk2
OS9 Drivers: No
Speed: 800 Mb/sec Speed
Unit Spec Id: 12512
Firmware Revision: 107a
Unit Software Version: 484944
let me know if i answered what you wanted, and if there are more ?'s. i haven't had a chance to try both 400's at once yet since i'm mid-job that i can't close right now.
thanks so much for your advice.

Two new external FW drives won't mount at the same time

Hi
I've just purchased two 250Gb external FW hard drives for my eMac. I already have a 60Gb external FW hard drive.
I also purchased a 6-port Belkin FW hub to hook them all up.
I've been having problems getting the three drives to mount simultaneously.
Initially I thought the problem was with the hub, or the FW cables, but the cables are fine, and if I take the hub out of the equation, and just try to mount two drives using the eMac's two FW ports, I still have problems.
Either of the two new 250Gb drives will mount fine with the old 60Gb drive, but if I try to mount the two 250Gb drives simultaneously, only one will mount (which ever I plugged in first).
The only way to get both 250Gb drives mounted at the same time is to use FW for one and USB for the other (way too slow).
The 250Gb drives are Hitachi Deskstars in enclosures with the Oxford chipset.
I've searched the internet for answers, but haven't found much, except, maybe, for this comment:
'While this cannot solve all FireWire issues, I've spent a lot of time debugging multiple FireWire enclosures on the same computer. Apparently there is a unique hardware ID (similar to a MAC address in an Ethernet card) that some manufacturers are not making unique. Any time you have two or more drives with the same ID, you'll have problems.'
Any ideas?
Thank you.

FWIW, I've tried to mount both drives on a friend's iBook, and the problem remains the same: it's one drive, or the other - both drives will not mount simultaneously.
I updated to 10.3.9, but that hasn't fixed anything.
Any ideas?

I can't measure many signals at the same time using the DAQCard-AI-16XE-50.

I'm using a Compaq Presario 1655 laptop with a DAQCard-AI-16XE-50 on the PCMCIA slot, and LabVIEW 6i and MAX 2.0.
I have a SCXI-1001 Chassis with SCXI-1122 and its terminal block SCXI-1322 installed (I have others too).
I'm trying to measure some signals at the same time, for instance, measuring 2 load cells signals, and a frequency of an indutive sensor (using the analog way with the "Extract Single Tone Information.vi").
I realized that I can't measure at the same time my signals, neither the load cells - a 10608 error occurrs "NI-DAQ LV: No transfer in progress for the specified resource".
What's the problem?
Some DAQCard limitation? Configuration?
Thanks!

Hello;
By your description I'm assuming you are trying to read those analog inputs in parallel. The SCXI-1122 doesn't have that feature. All the analog inputs will be multiplexed to one single Analog Input channel on your DAQ board. If you need to make measurements in parallel, you need to use one of the SCXI modules that allows that operation. For more information on what modules support that operation, you can always refer to our home page at www.ni.com.
Hope this helps.
Filipe
Applications Engineer
National Instruments

How can I get rid of multiple pictures at the same time?

how can I get rid of multiple pictures at the same time?

Adobe Bridge, lightroom and your file browser (windows explorer or Mac Finder) can select multiple pictures at once and then delete. If you are looking for more than that for information, you will need to be more specific at what your doing, what OS you have, and version of software your using. If necessary post screen shots so we can see what your doing. The more information we have the more detailed of an explaination can can give back to you.

How do I get 2 layers to move at the same time?

How do you get 2 layers to move at the same time?

Thanks for the help folks, sorry I've been away.
I'd love help with the problem of why I only one track seems to accept clips to play. When I drag them to other tracks or create a track by dragging the clips are grayed out and won't play, but if I drag them to the one track where they're blue they play.

Send two signals at the same time to serial

Hi
I have a problem in that I want to control some relay boards by serial. The boards have an address byte (to determine which of the three relay boards) and a relay combination (four relays on each board). The .vi I will need to make will be sending data to the serial as a result of feedback from sensors (they are currently simply controlled by timers to simulate) so there is a good chance that there will be two relay addresses sent at the same time and consequently much confusion. The timed simulation demonstrates this possibility by switching all relays on at the start.
Is there a way of avoiding this? Any help would be much appreciated.
Many thanks
Alastair

Alastair,
When you say send to multiple boards "at the same time" exactly what to you mean? On a serial port only one byte at a time can be sent. You do not specify how many bytes are sent to each board to handle the addressing, the data, and any EOT (End of Transmission) characters.
I can think of two possibilities.
1. Relays are slow. If the transmission rate is fast enough, you could send messages to all relays sequentially over the serial port but still have the appearance of simultaneous activation of the relays. If the relays switch in 10 ms and each command contains 6 bytes, sending the data at 115 kilobaud would take about 1.5 ms for three boards. This would likely be close enough to simultaneous for relays.
2. Add a command similar to the GPIB GET (Group Execute Trigger). All devices on the bus respond to this command by executing a previously stored command. No addressing is used for this command. This does require that the relay boards be modified to respond to their address and to the common or group address and to store a command for later execution.
Lynn

How can I tether via USB my iPhone 4S with iOS 7.1.1 to my MacBook with Snow Leopard 10.6.8 and iTunes 11.2.2 ?? Please note that at the same time Personal Hotspot via both WiFi and Bluetooth works perfectly!

How can I tether via USB my iPhone 4S with iOS 7.1.1 to my MacBook with Snow Leopard 10.6.8 and iTunes 11.2.2 ?? Please note that at the same time Personal Hotspot via both WiFi and Bluetooth works perfectly!

Hello, lustige luka.
Thank you for visiting Apple Support Communities.
The Personal Hotspot feature using USB should be as simple as connecting the device to your Mac via the USB cable when Hotspot is enabled. Here is some more information regarding this feature and an article that will provide some troubleshooting steps if you are experiencing an issue.
iOS: Understanding Personal Hotspot
http://support.apple.com/kb/ht4517
iOS: Troubleshooting Personal Hotspot
http://support.apple.com/kb/TS2756
Cheers,
Jason H.

Whenever I open a new tab a new window is also opening at the same time, and when i close that tab thet window is also closing. what to do?

Whenever I open a new tab a new window is also opening at the same time, and when i close that tab that window is also closing. what to do?

Swarnava, thank you very much! that did it and I am Bing-less . . . OH HAPPY DAY!! WOOHOO!!!! thank you, thank you, thank you!

When i open my firefox browser i get alot of windows opening at the same time

when i open my firefox browser i get alot of windows opening at the same time , this just started a couple of days ago , it is really annoying how do i fix this problem? this is the website that attacks my browser ... http://hosting.adjug.com/AdJugSearch/Results.aspx?ivi=V5PU&aid=1591&slid=116515&CacheBuster=81841886
== This happened ==
Every time Firefox opened
== july 1st 2010

The site adjug.com is a hosting site for advertising. See: http://www.robtex.com/r/x?q=adjug.com
Check your home page settings to see if they are correct: http://support.mozilla.com/en-US/kb/How+to+set+the+home+page
You may have been infected by some malware.
'''Check for Malware'''
Install, update and run these programs in this order. They are all free for personal use, but some have limited functionality in the "free mode", but those are features you really don't need to find and remove the problem that you have. ('''Not all programs detect the same Malware.''')
Malwarebytes' Anti-Malware - http://www.malwarebytes.org/mbam.php
SuperAntispyware - http://www.superantispyware.com/
AdAware - http://www.lavasoftusa.com/software/adaware/
Spybot Search & Destroy - http://www.safer-networking.org/en/index.html
Windows Defender - http://www.microsoft.com/windows/products/winfamily/defender/default.mspx
Dr. Web Cureit - http://www.freedrweb.com/cureit/
If these don't find it or can't clear it, post in one of these forums for specialized malware removal help:
http://bleepingcomputer.com
http://www.spywareinfoforum.com/
http://www.spywarewarrior.com/index.php
http://forum.aumha.org/
'''''Other Issues''''': ~~red:You have installed plug-ins with known security issues. You should update them immediately.~~
'''You''' ~~red:'''MAY'''~~ '''need to Update Adobe Reader for Firefox (aka Adobe PDF Plug-In For Firefox)''': your ver. N/A; current ver. 9.3.3 (important security update release 06-29-2010; see: http://www.adobe.com/support/security/bulletins/apsb10-15.html)
~~red:Check your version here~~: http://www.mozilla.com/en-US/plugincheck/
See: http://support.mozilla.com/en-US/kb/Using+the+Adobe+Reader+plugin+with+Firefox#Installing_and_updating_Adobe_Reader
''You may be able to update from the Adobe Reader installed on your system'' instead of going to the Adobe site and downloading. Start > Program Files, find and click Adobe Reader to open, click Help, click Check for Updates.
''If you go to the Adobe site to download the current Adobe Reader:''
-'''use Firefox to download''' and '''SAVE to your hard drive''' (save to Desktop for easy access)
~~red:-See the images at the bottom left of this post to see the steps to take on the Adobe site~~
-exit Firefox (File > Exit)
-check to see that Firefox is completely closed (''Ctrl+Alt+Del, choose Task Manager, click Processes tab, if "firefox.exe" is on the list, right-click "firefox.exe" and choose End process, close the Task Manager window'')
-double-click on the Adobe Reader installer you just downloaded to install/update Adobe Reader
*'''NOTE: On Vista and Windows 7''' you may need to run the plugin installer as Administrator by starting the installer via the right-click context menu if you do not get an UAC prompt to ask for permission to continue (i.e nothing seems to happen). See this: http://vistasupport.mvps.org/run_as_administrator.htm
*'''NOTE for IE:''' Firefox and most other browsers use a Plugin. IE uses an ActiveX version. To install/update the IE ActiveX version, same instructions as above, except use IE to download the ActiveX installer.
*Also see: http://kb.mozillazine.org/Adobe_Reader ~~red:'''''AND'''''~~ [[How do I edit options to add Adobe to the list of allowed sites]]

HT1430 my iphone 4 stopped working suddenly....i held the on button and the home button at the same time and it cam on...is this a fault as i cant have my phone switching off randomly?

my iphone 4 stopped working suddenly....it wouldnt charge or anything...i was told to push the on button and the home button at the same time and it came back on.
is this a fault with the iphone????
i cant have my phone switching off randomly...any help please...thankyou.

sometimes it happens, a hard reset will sometimes solve the issue.
If the issue starts happening more often, I would consider restoring the device to factory settings to install clean software. If the issue still persists after that, the device might need a hardware repair.
More info on backing up and restoring the software: http://support.apple.com/kb/HT4137
Good luck
Stijn

My newer IPhone gets a weaker cell signal at the same time and place as my wife's older one. Help

Similar Messages

Maybe you are looking for