My old ipod classic will charge but will no longer sync to my itunes. My computer does not recoginze that it is plugged in. Is it time to replace it?

My old ipod classic will charge when I plug it it in but my computer will no longer recognize that it is plugged in and Itunes will not pop up. Is it time to retire this 5 year old classic?

Hello, a.higgins.
Thank you for visiting Apple Support Communities.
Here are some troubleshooting steps in the article below that I would recommend going through.
iTunes: iPod not recognized in iTunes and Mac desktop
http://support.apple.com/kb/ts1410
Cheers,
Jason H.

Similar Messages

Ipod Nano will charge but will not play on dock

Hi,
My ipod nano (1st Gen) will charge but will not play on my philips DS7550/05 Docking station.
When i phoned Apple support they told me maybe it was because my ipod was not compatable with the Docking station but to follow that up i checked the system requirements and my ipod is perfectly compatable with this docking station.
Other ipods do work on this Dock. I tried resetting my ipod but that did not work. My ipod works fine through headphones, syncs through my computer and charges fine when i plug it into the dock but simply will not play music!
Any ideas would be greatly appreciated!!
Thanks

Not in particular. The fact that the iPod does not play when connected to any other docks could mean either the 1G Nano does not have the ability to output sound via it's dock connector port or yours in particular has gone bad.
B-rock

Using my old ipod classic 5g charger on the new ipod touch 3g?

is it possible to use my old ipod classic 5g charger on the new ipod touch 3g? thanks

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get aCode 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any Apple Software Updateentries and click "Remove", as per the following screenshot:
Next, select any Bonjour entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install using an iTunesSetup.exe (or iTunes64Setup.exe) downloaded from the Apple Website:
http://www.apple.com/itunes/download/
Does it go through properly this time?

Generally when creating a Word file from either a Mac or Win7 pc and opening it on two different machines (either one first) it always prompts that the file is open and will be opened as read only. However opening a CSS file does not prompt that it is alr

Generally when creating a Word file from either a Mac or Win7 pc and opening it on two different machines (either one first) it always prompts that the file is open and will be opened as read only.
However opening a CSS file does not prompt that it is already open on or from any machine which is causing code edits to be lost.
What we found from out testing:
- The file can be saved from one user to the server and WILL NOT PROMPT on other machines until the saving machine has the Dreamweaver program closed completely
- The file can be closed and Dreamweaver minimised to the launch bar but it still will not register on other machines that it has been changed.
- Also, until the Dreamweaver program is closed on the machines, it will continue to open it's saved version of the file.
Example Scenario:
- User 1 opens test.css (which is 2000 lines) and adds some code to the end of the file to bring it up to 2500 lines
- Meanwhile User 2 opens test.css as well (opens as 2000 lines as User 1’s edits have not yet been saved) and adds in code to bring it to 2300 lines
- User 1 saves his file and closes it - but Dreamweaver is still open.
- User 2 also saves his file and leaves Dreamweaver open.
- The server will report the size and last edit of the file the same as User 2 as he was the last person to save it (and if you open from the Win7 Machine it will show as User 2’s 2300 line version)
- If User 1 then open's the file again (from either the 'recent' in Dreamweaver OR clicking on the file directly in Finder...which version opens.... The version that User 1 saved! Not the true version on the server, but the version that User 1 edited and saved with 2500 lines in it.
- Same for User 2, he will open 'his' version with 2300 lines in.
Other information:
- Files are opened directly from the server
- Sometimes the users will save incrementally and re-open
- Most of the time users will save incrementally and keep the files open
- The users will never not save incrementally and just save when closing the file once finished
- The users are usually working on the files all day
- It is always the bottom lines of code that are lost. It could be a case of the two versions being mixed up and cutting off the newly added lines based on the line count (possibly).
It is as if Dreamweaver is holding a cache of the version locally and then only properly looking back to the server when it has been completely closed. It is very difficult to see how the server is causing such an impact on these files, there are very few logs which are giving any indication to the root cause of the problems.
Anyone know if this is a known issue?
Is there a way that there can be a featured implemented on the server that doesn't allow another user to open a file if it is already open on another machine?
Thanks

Your server file handling has nothing, and really nothing to do with Adobe software. If files don't get locked for (over-)writing and/or lose connection to the program opening them, then your server is misconfigured. It's as plain and simple and that. Anything from "known file types"/ file associations not being set correctly, MIME types being botched, crooked user privileges and file permissions, missing Mac server extensions, delayed file writing on the server, generic network timeout issues and what have you. Either way, you have written a longwinded post with no real value since you haven't bothered to provide any proper technical info, most notably about the alleged server. Either way, the only way you can "fix" it is by straightening out your server and network configuration, not some magic switch in Adobe's software.
Mylenium

Why will my new iPad no longer sync my non-iTunes TV shows?

My original iPad, as well as my iPhone 4S, synced perfectly with iTunes 10.6. I usually use the option Sync 3 Oldest Unwatched for the TV Shows that I add myself, but this no longer works for my new iPad; it does not recognize non-iTunes TV shows in my sync settings, and refuses to sync any of them unless I manually select the episodes. What could be the problem here?

Thank you for your reply and your suggestion. I did try using a different cable. The original cable was one that had been working perfectly well just last week. ITunes is still not styncing.

I want to give my old ipod to a friend, but I no longer have the serial #

I gave my old ipod to a friend, but we are both unsure if he can use it. I reased all of my songs, so it was blank. HIs wife has itunes but he is afraid to plug it in for fear that it will somehow affect her ipod. Do I need to somehow find the serial # (no idea how to do that) so he can register th ipod on itunes?

He does not need to register it and it will not affect her iPod. Just don't connect both of them at the same time. The serial number is on the iPod and when he connects it to his computer he can also click on the iPod in iTunes, move to the Summary tab to the right and the serial number will be displayed.

IPod Classic plays music, but will not show in iTuens or My computer

My ipod was working perfectly fine until 2 nights ago. I never had a problem with it then it just randomly disconnected from iTunes. I I safely removed it then plugged it back in and it froze iTunes, and didn't show in My Computer. After repeating the 5R's several times, I finally got the iPod to show, but it shows on My Computer as a drive that needs to be reformatted (both in normal and in disk mode) and I can't access it at all, when I click the ipod icon, the folder freezes for about 5-10 minutes then goes back to normal and tells me it can;t be accessed and needs to be reformatted. It will randomly show in iTunes but it will tell me that it needs to be restored to factory settings, which iTunes will not do for me.
The iPod itself works perfectly fine when its not hooked into my pc. It does everything its supposed to do. I tried hooking it in other PC's with different OS (all Windows) and I get the same result.
I also noticed that when I go into the iPod settings, it tells me that 28mb is free, when there should be about 30-40gb free. I have tried to use software like copy trans, stellar Phoenix and others but any program that tries to access the drive will freeze, lock up the pc or get a windows error.
I'm using an 80GB iPod Classic, running XP. The iPod, when hooked in, shows the typical connected logo with the two half circle arrows spinning. I get no error codes or messages other than Windows telling me it needs to be reformatted and iTunes telling me to restore it. I have no way--that I know of--to access any data on it. There is nothing in the iPod except for music and 2 videos, I haven't added any extra files to it in 2 weeks.

Same problem here - 80 gb classic and same thing happened to me this week - plays fine alone - when hooked to computer says it needs to be reformatted and then when i try to reformat i get error 1415 can't reformat - this is bs and im not shelling out for another ipod - why would it work fine but when connecting it to windows suddenly not work> I think Itunes 10 has got some issues

What can i do if my ipod 4g is charging but will not turn on?, what can i do if my ipod 4g is charging but will not turn on?

Hey guys!! Well i left my ipod outside for like 5 min. In the sun but then i went to get it and it said that the tempeture was too hot so i left it cool off for a minute. Then i turned it on and it was working fine but it ran out of battery and it turned off. I went to put it to charge and it said it was charging so i waited for it to turn on by itself but it never did. It just kept saying low battery charging. I left it to charge ALL night and when i woke up it still said low battery charging!! What can i do to fix this someone please help!!! Reseting it work, ? And how to reset?? THANKS!!!!!

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Ipod Classic 20gb charging, but "Unknown" to the computer

My Ipod Classic 20gb is charging when i plug it into the computer, but the computer will not see it as a device. I have tried putting it into disk mode, but the computer just says "Unknown USB Device." All I am trying to do is wipe the Ipod so I can put in a bunch of new music onto it so I am willing to wipe it.

To be of any assistance, I need the following info
Which version of itUnes are you using?
What is your iPod software version, as shown in the Itunes summary page? 1.1.2 or 2.0.4
Are you running Mac or Windows?
Have you tried the Hard Reset?
After charging till full charge, at least 2 hours (preferably 4 hours)
Toggle the Hold switch, make sure you dont see the red mark when you do the next step
Reset the iPod -> Press Menu and Center button simultaneously for about 10 secs or till the Apple Logo comes ON
Then release the buttons
Select your preferred language.
Here is the Apple support Article on the 5Rs
http://www.apple.com/support/ipod/five_rs/classic/
Have a nice day!

Why does my iPhone 4 not charge correctly? Problem is definitely with the phone and not charges or chords. Phone will charge but very slowly and no icon comes on. Computer and iTunes doesn't recognize it a being connected.

My iPhone 4 quit charging correctly. It does charge but very slowly and icon doesn't indicate it as charging. I've checked cables and charges and the problem is definetily with the phone. My car stereo no longer recognizes it as a device. Neither does the computer. The real strange thing to me is that when I plug it into my old klispch speaker dock it will play songs. My battery life is good when it is charged so I don't think its the battery. I've tried resetting the phone and cleaning the charging port. I'm out of warranty.
Would disconnecting the battery possibly reset it from some glitch or is the charging port got some bad contacts?

I checked with the Genius Bar. It was a new dilema to the lady that was helping me. She took it to a back room and worked on it but it came out the same. She gave me some options for repair or credit for replacement.
I just kept the phone and put up with slowly charging it by plugging it in and then turning it off.
I couldn't transfer anything from itunes.
I finally got fed up and bought a new charging port for $10. and a toolkit for $3. I looked up a video on youTube for the replacement and did it.
That solved all the problems, it was the charging port, must have been some bad pins or something because it patially worked.

My MacBook will charge but will not turn on

I have a 2010 MacBook that will charge and the light glows when it is shut but otherwise will not turn on. Any suggestions?

Hold the power button down for 10 seconds and then try to boot.
Try resetting NVRAM and SMC:
1. Reset PRAM. http://support.apple.com/kb/PH4405
2. Reset SMC. http://support.apple.com/kb/HT3964

Itunes and computer does not recognize Ipod USB connection

First off, I know this has been discussed over and over, but I am not getting any difinative answers so, I will start a new post. I have a Ipod mini and have had it for some time without any problems. Recently I added new music to Itunes and wanted to transfer it to my Ipod, but when I connect the USB cable it does will light up the screen to let me know that it has been connected, but it will not update the ipod and itunes will not recognize it and only a few times has it even charged the battery. I have tried to update itunes, update ipod (which didn't do any good since it is not being recognized), restored my ipod with play/menu, tried different usb outlets, and today I am going to get my sister's cable and try it. What am I doing wrong?!?!?!? I am going crazy about this. Thanks for any other suggestions.

Finally, I got it to work again. This is what I did. I doubt this is what changed anything but I reset all of my settings back to factory settings on the Ipod as far as backlight, shuffle, ect. I don't think this is what helped, but who knows with these things. Then I plugged it into the computer and it did show that it was charging (usually it did not even recognize enough to charge). Then I tried a different USB cable from my sister's Ipod and the first thing it did was ask to update Ipod and I did (I had to to plug it in to the wall to complete update) then I plugged it back in my computer and it finally worked! My husband thought I was an idiot because I was cheering every time it recognized something until I was basically jumping up and down when everything was updated. For now everything is back to normal so I love my Ipod again. Although my sister will get my old USB cable back seeing that she dropped her Ipod in water and hers does not work at all. Which reminds me to start another post about that. Thanks for all the support.

My ipod is fully charged but will not work it is telling to visit website support

Not sure what the model name is but it is an IPOD a1136...I had it charging went to turn it on and and an error message with an exclamation and a sad face advising to contact online support but I dont see anything online regarding the problem and how to fix it...Please help!

See Here > Device Not Recognised http://support.apple.com/kb/TS1538

Computer does not notice that my iPod is connected

Whenever I plug my iPod into my computer, My iPod will light up, but iTunes doesn't notice it is there, and neither does my computer, it will not charge or sync music which is very annoying, seeing as I just got it for Christmas...
Help me please, any ideas are welcome,
Thanks in advance

Have you had a chance to look at these troubleshooting pages? They may be of some help:
iPod missing in My Computer and in iTunes
iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
If you are using a laptop, this page might help: iPod not recognized when connected to Windows laptop over USB

IPod does not respond at all when plugged in

Alright, this topic is for people who have had this exact problem only. I don't want to get this confused with other problems and have people trying to help troubleshoot multiple problems and get things mixed up. Here's the problem.
After updating to v1.1.2 of the iPod software, the iPod does not respond when plugged in. The iPod still works fine when not plugged in. It plays music and both the standard and shuffle play modes work accordingly. The problem is when you plug the iPod in, it doesn't charge and it doesn't mount. The orange blinking light does not come on. While plugged in, it works the same way as it does when you're listening to music with it. It's as if the iPod's USB connector is dead. Here is my original post and description of the problem.
Alright, so here's my story. I bought my 512MB Shuffle in April. It has worked perfectly fine since I got it. Last night, I updated to v1.1.2 of the iPod software, clicked no when it asked if I wanted to restart, added some songs to the iPod, then restarted. As of this morning, I went to listen to some music while out for a bike ride, and I was greeted with the red battery light. I thought it was a bit odd since I had left it plugged in overnight. I figured, what the heck, I'll just plug it in and let it charge when I get back. When I got back, I plugged it into my PC and left for a while. I came back later and went to grab my Shuffle and I noticed it was cold, which was unusual after charging for a couple hours. I plugged it back in, a bit frustrated, and it never came up in Windows. I looked at the iPod plugged into the back of my PC (a high powered USB port) and sure enough, no orange light. No lights at all. I can still slide the switch to one of the play modes (standard play or shuffle) and play music for a couple seconds before it stops and says the battery's dead again. It works.. I mean it turns on and plays music, it's just not charging or mounting when I plug it in. I tried multiple computers and USB ports, none of which worked. I would really like some help with this considering it IS my only source of portable music and I'm not going to go pay $50 to talk to tech support or have it sent in for repairs. That's half of what it's worth.
I've tried uninstalling all iTunes/iPod related software from the PC I normally use it on and reinstalling it. That didn't work. I also tried uninstalling again and installing the last known working version of the iPod software, still no results. The only thing I havn't tried is giving it a good beating... Not that I would. Anyways, I hope there's a solution to this that doesn't involve buying a new one.
Here's a rundown of the computers I tested it with.
500MHZ G4 Cube (384MB RAM/Mac OSX Tiger)
400MHZ G3 iMac (384MB RAM/Mac OSX Tiger)
4.2GHZ AMD 64-Bit running Windows XP Service Pack 2 (my PC)
515MHZ Dell running Windows 2000 (256MB RAM)
UPDATE: The BIOS won't recognize the iPod, so it has nothing to do with my computer. Somehow, installing v1.1.2 of the iPod software made it so the iPod itself has USB problems. The iPod works to the extent of playing music and showing the battery charge level. I get no response at all when I plug it in, from the computer or the iPod.
I'm going to have to agree with Philip Harhay on this one. The original 10GB iPod I bought 3 years ago came with a full one-year warranty, no extra charges. I am disappointed to see the Shuffle only coming with a three-month warranty.
------------------------------------------------------------------

Help! I just purchase an iPod Shuffle for my son's birthday and I cannot get the darn thing to show up on my iMac G5. I am running OS 10.4.2 and I have downloaded the latest iPod and iTunes software. When I try to restore my iPod to the factory settings it tells me to plug the iPod into the computer, but it is plugged in. I have tried different USB ports, too. I'm running out of ideas and so is the trouble shooting Apple site. I was hoping someone out there might have some ideas.
It showed up at first and I transferred a few songs from the iTunes to the iPod but I couldn't get them to play, so I plugged it back into the USB and the icon never came up.

My old ipod classic will charge but will no longer sync to my itunes. My computer does not recoginze that it is plugged in. Is it time to replace it?

Similar Messages

Maybe you are looking for